[U-Boot] [RFC 1/3][v4] mmc: checking status after commands with R1b response

Marek Vasut marek.vasut at gmail.com
Sat Aug 6 14:07:42 CEST 2011


On Friday, March 11, 2011 01:18:15 PM Lei Wen wrote:
> On Fri, Mar 11, 2011 at 8:01 PM, Raffaele Recalcati
> 
> <lamiaposta71 at gmail.com> wrote:
> > From: Raffaele Recalcati <raffaele.recalcati at bticino.it>
> > 
> > It is recommended to check card status after these kind of commands.
> > This is done using CMD13 (SEND_STATUS) JEDEC command until
> > the card is ready.
> > In case of error the card status field is displayed.
> > 
> > Signed-off-by: Raffaele Recalcati <raffaele.recalcati at bticino.it>
> > ---
> >  drivers/mmc/mmc.c |   60
> > ++++++++++++++++++++++++++++++++++++++++++++++++++-- include/mmc.h     |
> >    4 +++
> >  2 files changed, 61 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c
> > index 6805b33..fc1792a 100644
> > --- a/drivers/mmc/mmc.c
> > +++ b/drivers/mmc/mmc.c
> > @@ -48,6 +48,40 @@ int mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
> > struct mmc_data *data) return mmc->send_cmd(mmc, cmd, data);
> >  }
> > 
> > +int mmc_send_status(struct mmc *mmc, int timeout)
> > +{
> > +       struct mmc_cmd cmd;
> > +       int err;
> > +       int status;
> > +
> > +       cmd.cmdidx = MMC_CMD_SEND_STATUS;
> > +       cmd.resp_type = MMC_RSP_R1;
> > +       cmd.cmdarg = 0;
> > +       cmd.flags = 0;
> > +
> > +       do {
> > +               err = mmc_send_cmd(mmc, &cmd, NULL);
> > +               if (err)
> > +                       return err;
> > +               else if (cmd.response[0] & MMC_STATUS_RDY_FOR_DATA)
> > +                       break;
> > +
> > +               udelay(1000);
> > +
> > +               if (cmd.response[0] & MMC_STATUS_MASK) {
> > +                       printf("Status Error: 0x%08X\n",
> > cmd.response[0]); +                       return COMM_ERR;
> > +               }
> > +       } while (timeout--);
> > +
> > +       if (!timeout) {
> > +               printf("Timeout waiting card ready\n");
> > +               return TIMEOUT;
> > +       }
> > +
> > +       return 0;
> > +}
> > +
> >  int mmc_set_blocklen(struct mmc *mmc, int len)
> >  {
> >        struct mmc_cmd cmd;
> > @@ -82,6 +116,7 @@ mmc_write_blocks(struct mmc *mmc, ulong start,
> > lbaint_t blkcnt, const void*src) {
> >        struct mmc_cmd cmd;
> >        struct mmc_data data;
> > +       int timeout = 1000;
> > 
> >        if ((start + blkcnt) > mmc->block_dev.lba) {
> >                printf("MMC: block number 0x%lx exceeds max(0x%lx)\n",
> > @@ -121,6 +156,9 @@ mmc_write_blocks(struct mmc *mmc, ulong start,
> > lbaint_t blkcnt, const void*src) printf("mmc fail to send stop cmd\n");
> >                        return 0;
> >                }
> > +
> > +               /* Waiting for the ready status */
> > +               mmc_send_status(mmc, 1000);
> >        }
> > 
> >        return blkcnt;
> > @@ -158,6 +196,7 @@ int mmc_read_blocks(struct mmc *mmc, void *dst, ulong
> > start, lbaint_t blkcnt) {
> >        struct mmc_cmd cmd;
> >        struct mmc_data data;
> > +       int timeout = 1000;
> > 
> >        if (blkcnt > 1)
> >                cmd.cmdidx = MMC_CMD_READ_MULTIPLE_BLOCK;
> > @@ -189,6 +228,9 @@ int mmc_read_blocks(struct mmc *mmc, void *dst, ulong
> > start, lbaint_t blkcnt) printf("mmc fail to send stop cmd\n");
> >                        return 0;
> >                }
> > +
> > +               /* Waiting for the ready status */
> > +               mmc_send_status(mmc, 1000);
> >        }
> > 
> >        return blkcnt;
> > @@ -369,15 +411,23 @@ int mmc_send_ext_csd(struct mmc *mmc, char
> > *ext_csd) int mmc_switch(struct mmc *mmc, u8 set, u8 index, u8 value)
> >  {
> >        struct mmc_cmd cmd;
> > +       int timeout = 1000;
> > +       int ret;
> > 
> >        cmd.cmdidx = MMC_CMD_SWITCH;
> >        cmd.resp_type = MMC_RSP_R1b;
> >        cmd.cmdarg = (MMC_SWITCH_MODE_WRITE_BYTE << 24) |
> > -               (index << 16) |
> > -               (value << 8);
> > +                                (index << 16) |
> > +                                (value << 8);
> >        cmd.flags = 0;
> > 
> > -       return mmc_send_cmd(mmc, &cmd, NULL);
> > +       ret = mmc_send_cmd(mmc, &cmd, NULL);
> > +
> > +       /* Waiting for the ready status */
> > +       mmc_send_status(mmc, 1000);
> > +
> > +       return ret;
> > +
> >  }
> > 
> >  int mmc_change_freq(struct mmc *mmc)
> > @@ -610,6 +660,7 @@ int mmc_startup(struct mmc *mmc)
> >        u64 cmult, csize;
> >        struct mmc_cmd cmd;
> >        char ext_csd[512];
> > +       int timeout = 1000;
> > 
> >        /* Put the Card in Identify Mode */
> >        cmd.cmdidx = MMC_CMD_ALL_SEND_CID;
> > @@ -722,6 +773,9 @@ int mmc_startup(struct mmc *mmc)
> >        cmd.flags = 0;
> >        err = mmc_send_cmd(mmc, &cmd, NULL);
> > 
> > +       /* Waiting for the ready status */
> > +       mmc_send_status(mmc, 1000);
> > +
> >        if (err)
> >                return err;
> > 
> > diff --git a/include/mmc.h b/include/mmc.h
> > index fcd0fd1..4ee8e1c 100644
> > --- a/include/mmc.h
> > +++ b/include/mmc.h
> > @@ -94,6 +94,10 @@
> >  #define OCR_BUSY       0x80000000
> >  #define OCR_HCS                0x40000000
> > 
> > +#define MMC_STATUS_MASK                (~0x0206BF7F)
> > +#define MMC_STATUS_RDY_FOR_DATA (1<<8)
> > +#define MMC_STATUS_CURR_STATE  (0xf<<9)
> > +
> >  #define MMC_VDD_165_195                0x00000080      /* VDD voltage
> > 1.65 - 1.95 */ #define MMC_VDD_20_21          0x00000100      /* VDD
> > voltage 2.0 ~ 2.1 */ #define MMC_VDD_21_22          0x00000200      /*
> > VDD voltage 2.1 ~ 2.2 */ --
> > 1.7.0.4
> 
> Works fine on Pantheon board. (armv5)
> Tested-by:Lei Wen <leiwen at marvell.com>

Hi,

have you tested this with cards operating in SPI mode ?

> 
> Best regards,
> Lei
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot


More information about the U-Boot mailing list