[U-Boot] [PATCH v5 1/2] ARMV7: Add support for Samsung ORIGEN board

Chander Kashyap chander.kashyap at linaro.org
Fri Aug 19 10:37:19 CEST 2011


Origen board is based upon S5PV310 SoC which is similiar to
S5PC210 SoC.

Signed-off-by: Chander Kashyap <chander.kashyap at linaro.org>
---
Changes for v2:
	- None
Changes for v3:
	- Board entry added Alphabetically in boards.cfg
	- Used get_Ram_size function to calculate ram size
Changes for v4:
	- CONFIG_MACH_TYPE defined to initialise MACH_TYPE in generic way
	- Used s5p_gpio_* functions for gpio operations
Changes for v5:
	- Used Symbolic names for hard-coded macros
	- Used get_ram_size() while initialising gd->bd->bi_dram[].size

 MAINTAINERS                          |    1 +
 board/samsung/origen/Makefile        |   46 +++
 board/samsung/origen/lowlevel_init.S |  357 ++++++++++++++++++++++
 board/samsung/origen/mem_setup.S     |  421 ++++++++++++++++++++++++++
 board/samsung/origen/origen.c        |  109 +++++++
 board/samsung/origen/origen_setup.h  |  546 ++++++++++++++++++++++++++++++++++
 boards.cfg                           |    1 +
 include/configs/origen.h             |  160 ++++++++++
 8 files changed, 1641 insertions(+), 0 deletions(-)
 create mode 100644 board/samsung/origen/Makefile
 create mode 100644 board/samsung/origen/lowlevel_init.S
 create mode 100644 board/samsung/origen/mem_setup.S
 create mode 100644 board/samsung/origen/origen.c
 create mode 100644 board/samsung/origen/origen_setup.h
 create mode 100644 include/configs/origen.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 6e6affa..8526642 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -709,6 +709,7 @@ Minkyu Kang <mk7.kang at samsung.com>
 
 Chander Kashyap <k.chander at samsung.com>
 
+	origen			ARM ARMV7 (S5PC210 SoC)
 	SMDKV310		ARM ARMV7 (S5PC210 SoC)
 
 Torsten Koschorrek <koschorrek at synertronixx.de>
diff --git a/board/samsung/origen/Makefile b/board/samsung/origen/Makefile
new file mode 100644
index 0000000..65eff91
--- /dev/null
+++ b/board/samsung/origen/Makefile
@@ -0,0 +1,46 @@
+#
+# Copyright (C) 2011 Samsung Electronics
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+SOBJS	:= mem_setup.o
+SOBJS	+= lowlevel_init.o
+COBJS	+= origen.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+all:	 $(obj).depend $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/samsung/origen/lowlevel_init.S b/board/samsung/origen/lowlevel_init.S
new file mode 100644
index 0000000..ddca1e2
--- /dev/null
+++ b/board/samsung/origen/lowlevel_init.S
@@ -0,0 +1,357 @@
+/*
+ * Lowlevel setup for ORIGEN board based on S5PV310
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+#include "origen_setup.h"
+/*
+ * Register usages:
+ *
+ * r5 has zero always
+ * r7 has GPIO part1 base 0x11400000
+ * r6 has GPIO part2 base 0x11000000
+ */
+
+_TEXT_BASE:
+	.word	CONFIG_SYS_TEXT_BASE
+
+	.globl lowlevel_init
+lowlevel_init:
+	push	{lr}
+
+	/* r5 has always zero */
+	mov	r5, #0
+	ldr	r7, =S5PC210_GPIO_PART1_BASE
+	ldr	r6, =S5PC210_GPIO_PART2_BASE
+
+	/* check reset status */
+	ldr	r0, =(S5PC210_POWER_BASE + INFORM1_OFFSET)
+	ldr	r1, [r0]
+
+	/* AFTR wakeup reset */
+	ldr	r2, =S5P_CHECK_DIDLE
+	cmp	r1, r2
+	beq	exit_wakeup
+
+	/* LPA wakeup reset */
+	ldr	r2, =S5P_CHECK_LPA
+	cmp	r1, r2
+	beq	exit_wakeup
+
+	/* Sleep wakeup reset */
+	ldr	r2, =S5P_CHECK_SLEEP
+	cmp	r1, r2
+	beq	wakeup_reset
+
+	/*
+	 * If U-boot is already running in ram, no need to relocate U-Boot.
+	 * Memory controller must be configured before relocating U-Boot
+	 * in ram.
+	 */
+	ldr	r0, =0x0ffffff		/* r0 <- Mask Bits*/
+	bic	r1, pc, r0		/* pc <- current addr of code */
+					/* r1 <- unmasked bits of pc */
+	ldr	r2, _TEXT_BASE		/* r2 <- original base addr in ram */
+	bic	r2, r2, r0		/* r2 <- unmasked bits of r2*/
+	cmp	r1, r2			/* compare r1, r2 */
+	beq	1f			/* r0 == r1 then skip sdram init */
+
+	/* init system clock */
+	bl system_clock_init
+
+	/* Memory initialize */
+	bl mem_ctrl_asm_init
+
+1:
+	/* for UART */
+	bl uart_asm_init
+	bl tzpc_init
+	pop	{pc}
+
+wakeup_reset:
+	bl system_clock_init
+	bl mem_ctrl_asm_init
+	bl tzpc_init
+
+exit_wakeup:
+	/* Load return address and jump to kernel */
+	ldr	r0, =(S5PC210_POWER_BASE + INFORM0_OFFSET)
+
+	/* r1 = physical address of s5pc210_cpu_resume function */
+	ldr	r1, [r0]
+
+	/* Jump to kernel*/
+	mov	pc, r1
+	nop
+	nop
+
+/*
+ * system_clock_init: Initialize core clock and bus clock.
+ * void system_clock_init(void)
+ */
+system_clock_init:
+	push	{lr}
+	ldr	r0, =S5PC210_CLOCK_BASE
+
+	/* APLL(1), MPLL(1), CORE(0), HPM(0) */
+	ldr	r1, =CLK_SRC_CPU_VAL
+	ldr	r2, =CLK_SRC_CPU_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x10000
+2:	subs	r1, r1, #1
+	bne	2b
+
+	ldr	r1, =CLK_SRC_TOP0_VAL
+	ldr	r2, =CLK_SRC_TOP0_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =CLK_SRC_TOP1_VAL
+	ldr	r2, =CLK_SRC_TOP1_OFFSET
+	str	r1, [r0, r2]
+
+	/* DMC */
+	ldr	r1, =CLK_SRC_DMC_VAL
+	ldr	r2, =CLK_SRC_DMC_OFFSET
+	str	r1, [r0, r2]
+
+	/*CLK_SRC_LEFTBUS */
+	ldr	r1, =CLK_SRC_LEFTBUS_VAL
+	ldr	r2, =CLK_SRC_LEFTBUS_OFFSET
+	str	r1, [r0, r2]
+
+	/*CLK_SRC_RIGHTBUS */
+	ldr	r1, =CLK_SRC_RIGHTBUS_VAL
+	ldr	r2, =CLK_SRC_RIGHTBUS_OFFSET
+	str	r1, [r0, r2]
+
+	/* SATA: SCLKMPLL(0), MMC[0:4]: SCLKMPLL(6) */
+	ldr	r1, =CLK_SRC_FSYS_VAL
+	ldr	r2, =CLK_SRC_FSYS_OFFSET
+	str	r1, [r0, r2]
+
+	/* UART[0:4] */
+	ldr	r1, =CLK_SRC_PERIL0_VAL
+	ldr	r2, =CLK_SRC_PERIL0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x10000
+3:	subs	r1, r1, #1
+	bne	3b
+
+	/* CLK_DIV_CPU0 */
+	ldr	r1, =CLK_DIV_CPU0_VAL
+	ldr	r2, =CLK_DIV_CPU0_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_CPU1 */
+	ldr	r1, =CLK_DIV_CPU1_VAL
+	ldr	r2, =CLK_DIV_CPU1_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_DMC0 */
+	ldr	r1, =CLK_DIV_DMC0_VAL
+	ldr	r2, =CLK_DIV_DMC0_OFFSET
+	str	r1, [r0, r2]
+
+	/*CLK_DIV_DMC1 */
+	ldr	r1, =CLK_DIV_DMC1_VAL
+	ldr	r2, =CLK_DIV_DMC1_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_LEFTBUS */
+	ldr	r1, =CLK_DIV_LEFTBUS_VAL
+	ldr	r2, =CLK_DIV_LEFTBUS_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_RIGHTBUS */
+	ldr	r1, =CLK_DIV_RIGHTBUS_VAL
+	ldr	r2, =CLK_DIV_RIGHTBUS_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_TOP */
+	ldr	r1, =CLK_DIV_TOP_VAL
+	ldr	r2, =CLK_DIV_TOP_OFFSET
+	str	r1, [r0, r2]
+
+	/* MMC[0:1] */
+	ldr	r1, =CLK_DIV_FSYS1_VAL		/* 800(MPLL) / (15 + 1) */
+	ldr	r2, =CLK_DIV_FSYS1_OFFSET
+	str	r1, [r0, r2]
+
+	/* MMC[2:3] */
+	ldr	r1, =CLK_DIV_FSYS2_VAL		/* 800(MPLL) / (15 + 1) */
+	ldr	r2, =CLK_DIV_FSYS2_OFFSET
+	str	r1, [r0, r2]
+
+	/* MMC4 */
+	ldr	r1, =CLK_DIV_FSYS3_VAL		/* 800(MPLL) / (15 + 1) */
+	ldr	r2, =CLK_DIV_FSYS3_OFFSET
+	str	r1, [r0, r2]
+
+	/* CLK_DIV_PERIL0: UART Clock Divisors */
+	ldr	r1, =CLK_DIV_PERIL0_VAL
+	ldr	r2, =CLK_DIV_PERIL0_OFFSET
+	str	r1, [r0, r2]
+
+	/* Set PLL locktime */
+	ldr	r1, =PLL_LOCKTIME
+	ldr	r2, =APLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =PLL_LOCKTIME
+	ldr	r2, =MPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =PLL_LOCKTIME
+	ldr	r2, =EPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	ldr	r1, =PLL_LOCKTIME
+	ldr	r2, =VPLL_LOCK_OFFSET
+	str	r1, [r0, r2]
+
+	/* APLL_CON1 */
+	ldr	r1, =APLL_CON1_VAL
+	ldr	r2, =APLL_CON1_OFFSET
+	str	r1, [r0, r2]
+
+	/* APLL_CON0 */
+	ldr	r1, =APLL_CON0_VAL
+	ldr	r2, =APLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* MPLL_CON1 */
+	ldr	r1, =MPLL_CON1_VAL
+	ldr	r2, =MPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+
+	/* MPLL_CON0 */
+	ldr	r1, =MPLL_CON0_VAL
+	ldr	r2, =MPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* EPLL */
+	ldr	r1, =EPLL_CON1_VAL
+	ldr	r2, =EPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+
+	/* EPLL_CON0 */
+	ldr	r1, =EPLL_CON0_VAL
+	ldr	r2, =EPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* VPLL_CON1 */
+	ldr	r1, =VPLL_CON1_VAL
+	ldr	r2, =VPLL_CON1_OFFSET
+	str	r1, [r0, r2]
+
+	/* VPLL_CON0 */
+	ldr	r1, =VPLL_CON0_VAL
+	ldr	r2, =VPLL_CON0_OFFSET
+	str	r1, [r0, r2]
+
+	/* wait ?us */
+	mov	r1, #0x30000
+4:	subs	r1, r1, #1
+	bne	4b
+
+	pop	{pc}
+/*
+ * uart_asm_init: Initialize UART in asm mode, 115200bps fixed.
+ * void uart_asm_init(void)
+ */
+	.globl uart_asm_init
+uart_asm_init:
+
+	/* setup UART0-UART3 GPIOs (part1) */
+	mov	r0, r7
+	ldr	r1, =S5PC210_GPIO_A0_CON_VAL
+	str	r1, [r0, #S5PC210_GPIO_A0_CON_OFFSET]
+	ldr	r1, =S5PC210_GPIO_A1_CON_VAL
+	str	r1, [r0, #S5PC210_GPIO_A1_CON_OFFSET]
+
+	ldr r0, =S5PC210_UART_BASE
+	add r0, r0, #S5PC210_DEFAULT_UART_OFFSET
+
+	ldr	r1, =ULCON_VAL
+	str	r1, [r0, #ULCON_OFFSET]
+	ldr	r1, =UCON_VAL
+	str	r1, [r0, #UCON_OFFSET]
+	ldr	r1, =UFCON_VAL
+	str	r1, [r0, #UFCON_OFFSET]
+	ldr	r1, =UBRDIV_VAL
+	str	r1, [r0, #UBRDIV_OFFSET]
+	ldr	r1, =UFRACVAL_VAL
+	str	r1, [r0, #UFRACVAL_OFFSET]
+	mov	pc, lr
+	nop
+	nop
+	nop
+
+/* Setting TZPC[TrustZone Protection Controller] */
+tzpc_init:
+	ldr	r0, =TZPC0_BASE
+	mov	r1, #R0SIZE
+	str	r1, [r0]
+	mov	r1, #DECPROTXSET
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC1_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC2_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC3_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC4_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	ldr	r0, =TZPC5_BASE
+	str	r1, [r0, #TZPC_DECPROT0SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT1SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT2SET_OFFSET]
+	str	r1, [r0, #TZPC_DECPROT3SET_OFFSET]
+
+	mov	pc, lr
diff --git a/board/samsung/origen/mem_setup.S b/board/samsung/origen/mem_setup.S
new file mode 100644
index 0000000..a798848
--- /dev/null
+++ b/board/samsung/origen/mem_setup.S
@@ -0,0 +1,421 @@
+/*
+ * Memory setup for ORIGEN board based on S5PV310
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include "origen_setup.h"
+#define SET_MIU
+
+	.globl mem_ctrl_asm_init
+mem_ctrl_asm_init:
+	/*
+	 * Async bridge configuration at CPU_core:
+	 * 1: half_sync
+	 * 0: full_sync
+	 */
+	ldr r0, =ASYNC_CONFIG
+	mov r1, #1
+	str r1, [r0]
+
+#ifdef SET_MIU
+	ldr	r0, =S5PC210_MIU_BASE
+	/* Interleave: 2Bit, Interleave_bit1: 0x21, Interleave_bit2: 0x7 */
+	ldr	r1, =0x20001507
+	str	r1, [r0, #APB_SFR_INTERLEAVE_CONF_OFFSET]
+
+	/* Update MIU Configuration */
+	ldr	r1, =0x00000001
+	str	r1, [r0, #APB_SFR_ARBRITATION_CONF_OFFSET]
+#endif
+	/* DREX0 */
+	ldr	r0, =S5PC210_DMC0_BASE
+
+	/*
+	 * DLL Parameter Setting:
+	 * Termination: Enable R/W
+	 * Phase Delay for DQS Cleaning: 180' Shift
+	 */
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/*
+	 * ZQ Calibration
+	 * Termination: Disable
+	 * Auto Calibration Start: Enable
+	 */
+	ldr	r1, =0xE3855703
+	str	r1, [r0, #DMC_PHYZQCONTROL]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+1:	subs	r2, r2, #1
+	bne	1b
+
+	/*
+	 * Update DLL Information:
+	 * Force DLL Resyncronization
+	 */
+	ldr	r1, =0xe000008e
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/* Reset Force DLL Resyncronization */
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/* Enable Differential DQS, DLL Off*/
+	ldr	r1, =0x71101008
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Activate PHY DLL: DLL On */
+	ldr	r1, =0x7110100A
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Set DLL Parameters */
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/* DLL Start */
+	ldr	r1, =0x7110100B
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	ldr	r1, =0x00000000
+	str	r1, [r0, #DMC_PHYCONTROL2]
+
+	/* Set Clock Ratio of Bus clock to Memory Clock */
+	ldr	r1, =0x0FFF301a
+	str	r1, [r0, #DMC_CONCONTROL]
+
+	/*
+	 * Memor Burst length: 8
+	 * Number of chips: 2
+	 * Memory Bus width: 32 bit
+	 * Memory Type: DDR3
+	 * Additional Latancy for PLL: 1 Cycle
+	 */
+	ldr	r1, =0x00312640
+	str	r1, [r0, #DMC_MEMCONTROL]
+
+	/*
+	 * Memory Configuration Chip 0
+	 * Address Mapping: Interleaved
+	 * Number of Column address Bits: 10 bits
+	 * Number of Rows Address Bits: 14
+	 * Number of Banks: 8
+	 */
+	ldr	r1, =0x20e01323
+	str	r1, [r0, #DMC_MEMCONFIG0]
+
+	/*
+	 * Memory Configuration Chip 1
+	 * Address Mapping: Interleaved
+	 * Number of Column address Bits: 10 bits
+	 * Number of Rows Address Bits: 14
+	 * Number of Banks: 8
+	 */
+	ldr	r1, =0x40e01323
+	str	r1, [r0, #DMC_MEMCONFIG1]
+
+	/* Config Precharge Policy */
+	ldr	r1, =0xff000000
+	str	r1, [r0, #DMC_PRECHCONFIG]
+
+	/*
+	 * TimingAref, TimingRow, TimingData, TimingPower Setting:
+	 * Values as per Memory AC Parameters
+	 */
+	ldr	r1, =0x000000BB
+	str	r1, [r0, #DMC_TIMINGAREF]
+	ldr	r1, =0x4046654f
+	str	r1, [r0, #DMC_TIMINGROW]
+	ldr	r1, =0x46400506
+	str	r1, [r0, #DMC_TIMINGDATA]
+	ldr	r1, =0x52000A3C
+	str	r1, [r0, #DMC_TIMINGPOWER]
+
+	/* Chip0: NOP Command: Assert and Hold CKE to high level */
+	ldr	r1, =0x07000000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+2:	subs	r2, r2, #1
+	bne	2b
+
+	/* Chip0: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	ldr	r1, =0x00020000
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00030000
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00010002
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00000328
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+3:	subs	r2, r2, #1
+	bne	3b
+
+	/* Chip0: ZQINIT */
+	ldr	r1, =0x0a000000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+4:	subs	r2, r2, #1
+	bne	4b
+
+	/* Chip1: NOP Command: Assert and Hold CKE to high level */
+	ldr	r1, =0x07100000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+5:	subs	r2, r2, #1
+	bne	5b
+
+	/* Chip1: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	ldr	r1, =0x00120000
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00130000
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00110002
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00100328
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+6:	subs	r2, r2, #1
+	bne	6b
+
+	/* Chip1: ZQINIT */
+	ldr	r1, =0x0a100000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+7:	subs	r2, r2, #1
+	bne	7b
+
+	ldr	r1, =0xe000008e
+	str	r1, [r0, #DMC_PHYCONTROL1]
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+8:	subs	r2, r2, #1
+	bne	8b
+
+	/* DREX1 */
+	ldr	r0, =S5PC210_DMC1_BASE	@0x10410000
+
+	/*
+	 * DLL Parameter Setting:
+	 * Termination: Enable R/W
+	 * Phase Delay for DQS Cleaning: 180' Shift
+	 */
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/*
+	 * ZQ Calibration:
+	 * Termination: Disable
+	 * Auto Calibration Start: Enable
+	 */
+	ldr	r1, =0xE3855703
+	str	r1, [r0, #DMC_PHYZQCONTROL]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+1:	subs	r2, r2, #1
+	bne	1b
+
+	/*
+	 * Update DLL Information:
+	 * Force DLL Resyncronization
+	 */
+	ldr	r1, =0xe000008e
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/* Reset Force DLL Resyncronization */
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/* Enable Differential DQS, DLL Off*/
+	ldr	r1, =0x71101008
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Activate PHY DLL: DLL On */
+	ldr	r1, =0x7110100A
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	/* Set DLL Parameters */
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/* DLL Start */
+	ldr	r1, =0x7110100B
+	str	r1, [r0, #DMC_PHYCONTROL0]
+
+	ldr	r1, =0x00000000
+	str	r1, [r0, #DMC_PHYCONTROL2]
+
+	/* Set Clock Ratio of Bus clock to Memory Clock */
+	ldr	r1, =0x0FFF301a
+	str	r1, [r0, #DMC_CONCONTROL]
+
+	/*
+	 * Memor Burst length: 8
+	 * Number of chips: 2
+	 * Memory Bus width: 32 bit
+	 * Memory Type: DDR3
+	 * Additional Latancy for PLL: 1 Cycle
+	 */
+	ldr	r1, =0x00312640
+	str	r1, [r0, #DMC_MEMCONTROL]
+
+	/*
+	 * Memory Configuration Chip 0
+	 * Address Mapping: Interleaved
+	 * Number of Column address Bits: 10 bits
+	 * Number of Rows Address Bits: 14
+	 * Number of Banks: 8
+	 */
+	ldr	r1, =0x20e01323
+	str	r1, [r0, #DMC_MEMCONFIG0]
+
+	/*
+	 * Memory Configuration Chip 1
+	 * Address Mapping: Interleaved
+	 * Number of Column address Bits: 10 bits
+	 * Number of Rows Address Bits: 14
+	 * Number of Banks: 8
+	 */
+	ldr	r1, =0x40e01323
+	str	r1, [r0, #DMC_MEMCONFIG1]
+
+	/* Config Precharge Policy */
+	ldr	r1, =0xff000000
+	str	r1, [r0, #DMC_PRECHCONFIG]
+
+	/*
+	 * TimingAref, TimingRow, TimingData, TimingPower Setting:
+	 * Values as per Memory AC Parameters
+	 */
+	ldr	r1, =0x000000BB
+	str	r1, [r0, #DMC_TIMINGAREF]
+	ldr	r1, =0x4046654f
+	str	r1, [r0, #DMC_TIMINGROW]
+	ldr	r1, =0x46400506
+	str	r1, [r0, #DMC_TIMINGDATA]
+	ldr	r1, =0x52000A3C
+	str	r1, [r0, #DMC_TIMINGPOWER]
+
+	/* Chip0: NOP Command: Assert and Hold CKE to high level */
+	ldr	r1, =0x07000000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+2:	subs	r2, r2, #1
+	bne	2b
+
+	/* Chip0: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	ldr	r1, =0x00020000
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00030000
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00010002
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00000328
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+3:	subs	r2, r2, #1
+	bne	3b
+
+	/* Chip 0: ZQINIT */
+	ldr	r1, =0x0a000000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+4:	subs	r2, r2, #1
+	bne	4b
+
+	/* Chip1: NOP Command: Assert and Hold CKE to high level */
+	ldr	r1, =0x07100000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+5:	subs	r2, r2, #1
+	bne	5b
+
+	/* Chip1: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	ldr	r1, =0x00120000
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00130000
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00110002
+	str	r1, [r0, #DMC_DIRECTCMD]
+	ldr	r1, =0x00100328
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+6:	subs	r2, r2, #1
+	bne	6b
+
+	/* Chip1: ZQINIT */
+	ldr	r1, =0x0a100000
+	str	r1, [r0, #DMC_DIRECTCMD]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+7:	subs	r2, r2, #1
+	bne	7b
+
+	ldr	r1, =0xe000008e
+	str	r1, [r0, #DMC_PHYCONTROL1]
+	ldr	r1, =0xe0000086
+	str	r1, [r0, #DMC_PHYCONTROL1]
+
+	/* Wait ?us*/
+	mov	r2, #0x100000
+8:	subs	r2, r2, #1
+	bne	8b
+
+	/* turn on DREX0, DREX1 */
+	ldr	r0, =S5PC210_DMC0_BASE
+	ldr	r1, =0x0FFF303a
+	str	r1, [r0, #DMC_CONCONTROL]
+
+	ldr	r0, =S5PC210_DMC1_BASE
+	ldr	r1, =0x0FFF303a
+	str	r1, [r0, #DMC_CONCONTROL]
+
+	mov	pc, lr
diff --git a/board/samsung/origen/origen.c b/board/samsung/origen/origen.c
new file mode 100644
index 0000000..8882646
--- /dev/null
+++ b/board/samsung/origen/origen.c
@@ -0,0 +1,109 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+struct s5pc210_gpio_part1 *gpio1;
+struct s5pc210_gpio_part2 *gpio2;
+
+int board_init(void)
+{
+	gpio1 = (struct s5pc210_gpio_part1 *) S5PC210_GPIO_PART1_BASE;
+	gpio2 = (struct s5pc210_gpio_part2 *) S5PC210_GPIO_PART2_BASE;
+
+	gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size	= get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE)
+			+ get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE);
+
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, \
+							PHYS_SDRAM_1_SIZE);
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, \
+							PHYS_SDRAM_2_SIZE);
+	gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
+	gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, \
+							PHYS_SDRAM_3_SIZE);
+	gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
+	gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, \
+							PHYS_SDRAM_4_SIZE);
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+	printf("\nBoard: ORIGEN\n");
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+	int i, err;
+
+	/*
+	 * MMC2 SD card GPIO:
+	 *
+	 * GPK2[0]	SD_2_CLK(2)
+	 * GPK2[1]	SD_2_CMD(2)
+	 * GPK2[2]	SD_2_CDn
+	 * GPK2[3:6]	SD_2_DATA[0:3](2)
+	 */
+	for (i = 0; i < 7; i++) {
+		/* GPK2[0:6] special function 2 */
+		s5p_gpio_cfg_pin(&gpio2->k2, i, GPIO_FUNC(0x2));
+
+		/* GPK2[0:6] drv 4x */
+		s5p_gpio_set_drv(&gpio2->k2, i, GPIO_DRV_4X);
+
+		/* GPK2[0:1] pull disable */
+		if (i == 0 || i == 1) {
+			s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_NONE);
+			continue;
+		}
+
+		/* GPK2[2:6] pull up */
+		s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_UP);
+	}
+
+	err = s5p_mmc_init(2, 4);
+	return err;
+}
+#endif
diff --git a/board/samsung/origen/origen_setup.h b/board/samsung/origen/origen_setup.h
new file mode 100644
index 0000000..63d85d8
--- /dev/null
+++ b/board/samsung/origen/origen_setup.h
@@ -0,0 +1,546 @@
+/*
+ * Machine Specific Values for ORIGEN board based on S5PV310
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _ORIGEN_SETUP_H
+#define _ORIGEN_SETUP_H
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+
+/* Offsets of clock registers (sources and dividers) */
+#define CLK_SRC_CPU_OFFSET	0x14200
+#define CLK_DIV_CPU0_OFFSET	0x14500
+#define CLK_DIV_CPU1_OFFSET	0x14504
+
+#define CLK_SRC_DMC_OFFSET	0x10200
+#define CLK_DIV_DMC0_OFFSET	0x10500
+#define CLK_DIV_DMC1_OFFSET	0x10504
+
+#define CLK_SRC_TOP0_OFFSET	0xC210
+#define CLK_SRC_TOP1_OFFSET	0xC214
+#define CLK_DIV_TOP_OFFSET	0xC510
+
+#define CLK_SRC_LEFTBUS_OFFSET	0x4200
+#define CLK_DIV_LEFTBUS_OFFSET	0x4500
+
+#define CLK_SRC_RIGHTBUS_OFFSET	0x8200
+#define CLK_DIV_RIGHTBUS_OFFSET	0x8500
+
+#define CLK_SRC_FSYS_OFFSET	0xC240
+#define CLK_DIV_FSYS1_OFFSET	0xC544
+#define CLK_DIV_FSYS2_OFFSET	0xC548
+#define CLK_DIV_FSYS3_OFFSET	0xC54C
+
+#define CLK_SRC_PERIL0_OFFSET	0xC250
+#define CLK_DIV_PERIL0_OFFSET	0xC550
+
+#define APLL_LOCK_OFFSET	0x14000
+#define MPLL_LOCK_OFFSET	0x14008
+#define APLL_CON0_OFFSET	0x14100
+#define APLL_CON1_OFFSET	0x14104
+#define MPLL_CON0_OFFSET	0x14108
+#define MPLL_CON1_OFFSET	0x1410C
+
+#define EPLL_LOCK_OFFSET	0xC010
+#define VPLL_LOCK_OFFSET	0xC020
+#define EPLL_CON0_OFFSET	0xC110
+#define EPLL_CON1_OFFSET	0xC114
+#define VPLL_CON0_OFFSET	0xC120
+#define VPLL_CON1_OFFSET	0xC124
+
+/* DMC: DRAM Controllor Register offsets */
+#define DMC_CONCONTROL		0x00
+#define DMC_MEMCONTROL		0x04
+#define DMC_MEMCONFIG0		0x08
+#define DMC_MEMCONFIG1		0x0C
+#define DMC_DIRECTCMD		0x10
+#define DMC_PRECHCONFIG		0x14
+#define DMC_PHYCONTROL0		0x18
+#define DMC_PHYCONTROL1		0x1C
+#define DMC_PHYCONTROL2		0x20
+#define DMC_TIMINGAREF		0x30
+#define DMC_TIMINGROW		0x34
+#define DMC_TIMINGDATA		0x38
+#define DMC_TIMINGPOWER		0x3C
+#define DMC_PHYZQCONTROL	0x44
+
+/* Bus Configuration Register Address */
+#define ASYNC_CONFIG		0x10010350
+
+/* MIU Config Register Offsets*/
+#define APB_SFR_INTERLEAVE_CONF_OFFSET	0x400
+#define APB_SFR_ARBRITATION_CONF_OFFSET		0xC00
+
+/* Offset for inform registers */
+#define INFORM0_OFFSET			0x800
+#define INFORM1_OFFSET			0x804
+
+/* GPIO Offsets for UART: GPIO Contol Register */
+#define S5PC210_GPIO_A0_CON_OFFSET	0x00
+#define S5PC210_GPIO_A1_CON_OFFSET	0x20
+
+/* UART Register offsets */
+#define ULCON_OFFSET		0x00
+#define UCON_OFFSET		0x04
+#define UFCON_OFFSET		0x08
+#define UBRDIV_OFFSET		0x28
+#define UFRACVAL_OFFSET		0x2C
+
+/* TZPC : Register Offsets */
+#define TZPC0_BASE		0x10110000
+#define TZPC1_BASE		0x10120000
+#define TZPC2_BASE		0x10130000
+#define TZPC3_BASE		0x10140000
+#define TZPC4_BASE		0x10150000
+#define TZPC5_BASE		0x10160000
+
+#define TZPC_DECPROT0SET_OFFSET	0x804
+#define TZPC_DECPROT1SET_OFFSET	0x810
+#define TZPC_DECPROT2SET_OFFSET	0x81C
+#define TZPC_DECPROT3SET_OFFSET	0x828
+
+/* CLK_SRC_CPU */
+#define MUX_HPM_SEL_MOUTAPLL		0x0
+#define MUX_HPM_SEL_SCLKMPLL		0x1
+#define MUX_CORE_SEL_MOUTAPLL		0x0
+#define MUX_CORE_SEL_SCLKMPLL		0x1
+#define MUX_MPLL_SEL_FILPLL		0x0
+#define MUX_MPLL_SEL_MOUTMPLLFOUT	0x1
+#define MUX_APLL_SEL_FILPLL		0x0
+#define MUX_APLL_SEL_MOUTMPLLFOUT	0x1
+#define CLK_SRC_CPU_VAL			((MUX_HPM_SEL_MOUTAPLL << 20) \
+					| (MUX_CORE_SEL_MOUTAPLL << 16) \
+					| (MUX_MPLL_SEL_MOUTMPLLFOUT << 8)\
+					| (MUX_APLL_SEL_MOUTMPLLFOUT << 0))
+
+/* CLK_DIV_CPU0 */
+#define APLL_RATIO		0x0
+#define PCLK_DBG_RATIO		0x1
+#define ATB_RATIO		0x3
+#define PERIPH_RATIO		0x3
+#define COREM1_RATIO		0x7
+#define COREM0_RATIO		0x3
+#define CORE_RATIO		0x0
+#define CLK_DIV_CPU0_VAL	((APLL_RATIO << 24) \
+				| (PCLK_DBG_RATIO << 20) \
+				| (ATB_RATIO << 16) \
+				| (PERIPH_RATIO << 12) \
+				| (COREM1_RATIO << 8) \
+				| (COREM0_RATIO << 4) \
+				| (CORE_RATIO << 0))
+
+/* CLK_DIV_CPU1 */
+#define HPM_RATIO		0x0
+#define COPY_RATIO		0x3
+#define CLK_DIV_CPU1_VAL	((HPM_RATIO << 4) | (COPY_RATIO))
+
+/* CLK_SRC_DMC */
+#define MUX_PWI_SEL_XXTI		0x0
+#define MUX_PWI_SEL_XUSBXTI		0x1
+#define MUX_PWI_SEL_SCLK_HDMI24M	0x2
+#define MUX_PWI_SEL_SCLK_USBPHY0	0x3
+#define MUX_PWI_SEL_SCLK_USBPHY1	0x4
+#define MUX_PWI_SEL_SCLK_HDMIPHY	0x5
+#define MUX_PWI_SEL_SCLKMPLL		0x6
+#define MUX_PWI_SEL_SCLKEPLL		0x7
+#define MUX_PWI_SEL_SCLKVPLL		0x8
+#define MUX_DPHY_SEL_SCLKMPLL		0x0
+#define MUX_DPHY_SEL_SCLKAPLL		0x1
+#define MUX_DMC_BUS_SEL_SCLKMPLL	0x0
+#define MUX_DMC_BUS_SEL_SCLKAPLL	0x1
+#define CLK_SRC_DMC_VAL			((MUX_PWI_SEL_XUSBXTI << 16) \
+					| (MUX_DPHY_SEL_SCLKMPLL << 8) \
+					| (MUX_DMC_BUS_SEL_SCLKMPLL << 4))
+
+/* CLK_DIV_DMC0 */
+#define CORE_TIMERS_RATIO	0x1
+#define COPY2_RATIO		0x3
+#define DMCP_RATIO		0x1
+#define DMCD_RATIO		0x1
+#define DMC_RATIO		0x1
+#define DPHY_RATIO		0x1
+#define ACP_PCLK_RATIO		0x1
+#define ACP_RATIO		0x3
+#define CLK_DIV_DMC0_VAL	((CORE_TIMERS_RATIO << 28) \
+				| (COPY2_RATIO << 24) \
+				| (DMCP_RATIO << 20) \
+				| (DMCD_RATIO << 16) \
+				| (DMC_RATIO << 12) \
+				| (DPHY_RATIO << 8) \
+				| (ACP_PCLK_RATIO << 4)	\
+				| (ACP_RATIO << 0))
+
+/* CLK_DIV_DMC1 */
+#define DPM_RATIO		0x1
+#define DVSEM_RATIO		0x1
+#define PWI_RATIO		0x1
+#define CLK_DIV_DMC1_VAL	((DPM_RATIO << 24) \
+				| (DVSEM_RATIO << 16) \
+				| (PWI_RATIO << 8))
+
+/* CLK_SRC_TOP0 */
+#define MUX_ONENAND_SEL_ACLK_133	0x0
+#define MUX_ONENAND_SEL_ACLK_160	0x1
+#define MUX_ACLK_133_SEL_SCLKMPLL	0x0
+#define MUX_ACLK_133_SEL_SCLKAPLL	0x1
+#define MUX_ACLK_160_SEL_SCLKMPLL	0x0
+#define MUX_ACLK_160_SEL_SCLKAPLL	0x1
+#define MUX_ACLK_100_SEL_SCLKMPLL	0x0
+#define MUX_ACLK_100_SEL_SCLKAPLL	0x1
+#define MUX_ACLK_200_SEL_SCLKMPLL	0x0
+#define MUX_ACLK_200_SEL_SCLKAPLL	0x1
+#define MUX_VPLL_SEL_FINPLL		0x0
+#define MUX_VPLL_SEL_FOUTVPLL		0x1
+#define MUX_EPLL_SEL_FINPLL		0x0
+#define MUX_EPLL_SEL_FOUTEPLL		0x1
+#define MUX_ONENAND_1_SEL_MOUTONENAND	0x0
+#define MUX_ONENAND_1_SEL_SCLKVPLL	0x1
+#define CLK_SRC_TOP0_VAL		((MUX_ONENAND_SEL_ACLK_133 << 28) \
+					| (MUX_ACLK_133_SEL_SCLKMPLL << 24) \
+					| (MUX_ACLK_160_SEL_SCLKMPLL << 20) \
+					| (MUX_ACLK_100_SEL_SCLKMPLL << 16) \
+					| (MUX_ACLK_200_SEL_SCLKMPLL << 12) \
+					| (MUX_VPLL_SEL_FINPLL << 8) \
+					| (MUX_EPLL_SEL_FINPLL << 4)\
+					| (MUX_ONENAND_1_SEL_MOUTONENAND << 0))
+
+/* CLK_SRC_TOP1 */
+#define VPLLSRC_SEL_FINPLL	0x0
+#define VPLLSRC_SEL_SCLKHDMI24M	0x1
+#define CLK_SRC_TOP1_VAL	(VPLLSRC_SEL_FINPLL)
+
+/* CLK_DIV_TOP */
+#define ONENAND_RATIO		0x0
+#define ACLK_133_RATIO		0x5
+#define ACLK_160_RATIO		0x4
+#define ACLK_100_RATIO		0x7
+#define ACLK_200_RATIO		0x3
+#define CLK_DIV_TOP_VAL		((ONENAND_RATIO << 16)	\
+				| (ACLK_133_RATIO << 12)\
+				| (ACLK_160_RATIO << 8)	\
+				| (ACLK_100_RATIO << 4)	\
+				| (ACLK_200_RATIO << 0))
+
+/* CLK_SRC_LEFTBUS */
+#define MUX_GDL_SEL_SCLKMPLL	0x0
+#define MUX_GDL_SEL_SCLKAPLL	0x1
+#define CLK_SRC_LEFTBUS_VAL	(MUX_GDL_SEL_SCLKMPLL)
+
+/* CLK_DIV_LEFTBUS */
+#define GPL_RATIO		0x1
+#define GDL_RATIO		0x3
+#define CLK_DIV_LEFTBUS_VAL	((GPL_RATIO << 4) | (GDL_RATIO))
+
+/* CLK_SRC_RIGHTBUS */
+#define MUX_GDR_SEL_SCLKMPLL	0x0
+#define MUX_GDR_SEL_SCLKAPLL	0x1
+#define CLK_SRC_RIGHTBUS_VAL	(MUX_GDR_SEL_SCLKMPLL)
+
+/* CLK_DIV_RIGHTBUS */
+#define GPR_RATIO		0x1
+#define GDR_RATIO		0x3
+#define CLK_DIV_RIGHTBUS_VAL	((GPR_RATIO << 4) | (GDR_RATIO))
+
+/* CLK_SRS_FSYS: 6 = SCLKMPLL */
+#define SATA_SEL_SCLKMPLL	0
+#define SATA_SEL_SCLKAPLL	1
+
+#define MMC_SEL_XXTI		0
+#define MMC_SEL_XUSBXTI		1
+#define MMC_SEL_SCLK_HDMI24M	2
+#define MMC_SEL_SCLK_USBPHY0	3
+#define MMC_SEL_SCLK_USBPHY1	4
+#define MMC_SEL_SCLK_HDMIPHY	5
+#define MMC_SEL_SCLKMPLL	6
+#define MMC_SEL_SCLKEPLL	7
+#define MMC_SEL_SCLKVPLL	8
+
+#define MMCC0_SEL		MMC_SEL_SCLKMPLL
+#define MMCC1_SEL		MMC_SEL_SCLKMPLL
+#define MMCC2_SEL		MMC_SEL_SCLKMPLL
+#define MMCC3_SEL		MMC_SEL_SCLKMPLL
+#define MMCC4_SEL		MMC_SEL_SCLKMPLL
+#define CLK_SRC_FSYS_VAL	((SATA_SEL_SCLKMPLL << 24) \
+				| (MMCC4_SEL << 16) \
+				| (MMCC3_SEL << 12) \
+				| (MMCC2_SEL << 8) \
+				| (MMCC1_SEL << 4) \
+				| (MMCC0_SEL << 0))
+
+/* SCLK_MMC[0-4] = MOUTMMC[0-4]/(MMC[0-4]_RATIO + 1)/(MMC[0-4]_PRE_RATIO +1) */
+/* CLK_DIV_FSYS1 */
+#define MMC0_RATIO		0xF
+#define MMC0_PRE_RATIO		0x0
+#define MMC1_RATIO		0xF
+#define MMC1_PRE_RATIO		0x0
+#define CLK_DIV_FSYS1_VAL	((MMC1_PRE_RATIO << 24) \
+				| (MMC1_RATIO << 16) \
+				| (MMC0_PRE_RATIO << 8) \
+				| (MMC0_RATIO << 0))
+
+/* CLK_DIV_FSYS2 */
+#define MMC2_RATIO		0xF
+#define MMC2_PRE_RATIO		0x0
+#define MMC3_RATIO		0xF
+#define MMC3_PRE_RATIO		0x0
+#define CLK_DIV_FSYS2_VAL	((MMC3_PRE_RATIO << 24) \
+				| (MMC3_RATIO << 16) \
+				| (MMC2_PRE_RATIO << 8) \
+				| (MMC2_RATIO << 0))
+
+/* CLK_DIV_FSYS3 */
+#define MMC4_RATIO		0xF
+#define MMC4_PRE_RATIO		0x0
+#define CLK_DIV_FSYS3_VAL	((MMC4_PRE_RATIO << 8) \
+				| (MMC4_RATIO << 0))
+
+/* CLK_SRC_PERIL0 */
+#define UART_SEL_XXTI		0
+#define UART_SEL_XUSBXTI	1
+#define UART_SEL_SCLK_HDMI24M	2
+#define UART_SEL_SCLK_USBPHY0	3
+#define UART_SEL_SCLK_USBPHY1	4
+#define UART_SEL_SCLK_HDMIPHY	5
+#define UART_SEL_SCLKMPLL	6
+#define UART_SEL_SCLKEPLL	7
+#define UART_SEL_SCLKVPLL	8
+
+#define UART0_SEL		UART_SEL_SCLKMPLL
+#define UART1_SEL		UART_SEL_SCLKMPLL
+#define UART2_SEL		UART_SEL_SCLKMPLL
+#define UART3_SEL		UART_SEL_SCLKMPLL
+#define UART4_SEL		UART_SEL_SCLKMPLL
+#define CLK_SRC_PERIL0_VAL	((UART4_SEL << 16) \
+				| (UART3_SEL << 12) \
+				| (UART2_SEL << 8) \
+				| (UART1_SEL << 4) \
+				| (UART0_SEL << 0))
+
+/* SCLK_UART[0-4] = MOUTUART[0-4]/(UART[0-4]_RATIO + 1) */
+/* CLK_DIV_PERIL0 */
+#define UART0_RATIO		7
+#define UART1_RATIO		7
+#define UART2_RATIO		7
+#define UART3_RATIO		7
+#define UART4_RATIO		7
+#define CLK_DIV_PERIL0_VAL	((UART4_RATIO << 16) \
+				| (UART3_RATIO << 12) \
+				| (UART2_RATIO << 8) \
+				| (UART1_RATIO << 4) \
+				| (UART0_RATIO << 0))
+
+/* Required period to generate a stable clock output */
+/* PLL_LOCK_TIME */
+#define PLL_LOCKTIME		0x1C20
+
+/* PLL Values */
+#define DISABLE			0
+#define ENABLE			1
+#define SET_PLL(mdiv, pdiv, sdiv)	((ENABLE << 31)\
+					| (mdiv << 16) \
+					| (pdiv << 8) \
+					| (sdiv << 0))
+
+/* APLL_CON0 */
+#define APLL_MDIV		0xFA
+#define APLL_PDIV		0x6
+#define APLL_SDIV		0x1
+#define APLL_CON0_VAL		SET_PLL(APLL_MDIV, APLL_PDIV, APLL_SDIV)
+
+/* APLL_CON1 */
+#define APLL_AFC_ENB		0x1
+#define APLL_AFC		0xC
+#define APLL_CON1_VAL		((APLL_AFC_ENB << 31) | (APLL_AFC << 0))
+
+/* MPLL_CON0 */
+#define MPLL_MDIV		0xC8
+#define MPLL_PDIV		0x6
+#define MPLL_SDIV		0x1
+#define MPLL_CON0_VAL		SET_PLL(MPLL_MDIV, MPLL_PDIV, MPLL_SDIV)
+
+/* MPLL_CON1 */
+#define MPLL_AFC_ENB		0x0
+#define MPLL_AFC		0x1C
+#define MPLL_CON1_VAL		((MPLL_AFC_ENB << 31) | (MPLL_AFC << 0))
+
+/* EPLL_CON0 */
+#define EPLL_MDIV		0x30
+#define EPLL_PDIV		0x3
+#define EPLL_SDIV		0x2
+#define EPLL_CON0_VAL		SET_PLL(EPLL_MDIV, EPLL_PDIV, EPLL_SDIV)
+
+/* EPLL_CON1 */
+#define EPLL_K			0x0
+#define EPLL_CON1_VAL		(EPLL_K >> 0)
+
+/* VPLL_CON0 */
+#define VPLL_MDIV		0x35
+#define VPLL_PDIV		0x3
+#define VPLL_SDIV		0x2
+#define VPLL_CON0_VAL		SET_PLL(VPLL_MDIV, VPLL_PDIV, VPLL_SDIV)
+
+/* VPLL_CON1 */
+#define VPLL_SSCG_EN		DISABLE
+#define VPLL_SEL_PF_DN_SPREAD	0x0
+#define VPLL_MRR		0x11
+#define VPLL_MFR		0x0
+#define VPLL_K			0x400
+#define VPLL_CON1_VAL		((VPLL_SSCG_EN << 31)\
+				| (VPLL_SEL_PF_DN_SPREAD << 29) \
+				| (VPLL_MRR << 24) \
+				| (VPLL_MFR << 16) \
+				| (VPLL_K << 0))
+/*
+ * UART GPIO_A0/GPIO_A1 Control Register Value
+ * 0x2: UART Function
+ */
+#define S5PC210_GPIO_A0_CON_VAL	0x22222222
+#define S5PC210_GPIO_A1_CON_VAL	0x222222
+
+/* ULCON: UART Line Control Value 8N1 */
+#define WORD_LEN_5_BIT		0x00
+#define WORD_LEN_6_BIT		0x01
+#define WORD_LEN_7_BIT		0x02
+#define WORD_LEN_8_BIT		0x03
+
+#define STOP_BIT_1		0x00
+#define STOP_BIT_2		0x01
+
+#define NO_PARITY			0x00
+#define ODD_PARITY			0x4
+#define EVEN_PARITY			0x5
+#define FORCED_PARITY_CHECK_AS_1	0x6
+#define FORCED_PARITY_CHECK_AS_0	0x7
+
+#define INFRAMODE_NORMAL		0x00
+#define INFRAMODE_INFRARED		0x01
+
+#define ULCON_VAL		((INFRAMODE_NORMAL << 6) \
+				| (NO_PARITY << 3) \
+				| (STOP_BIT_1 << 2) \
+				| (WORD_LEN_8_BIT << 0))
+
+/*
+ * UCON: UART Control Value
+ * Tx_interrupt Type: Level
+ * Rx_interrupt Type: Level
+ * Rx Timeout Enabled: Yes
+ * Rx-Error Atatus_Int Enable: Yes
+ * Loop_Back: No
+ * Break Signal: No
+ * Transmit mode : Interrupt request/polling
+ * Receive mode : Interrupt request/polling
+ */
+#define TX_PULSE_INTERRUPT	0
+#define TX_LEVEL_INTERRUPT	1
+#define RX_PULSE_INTERRUPT	0
+#define RX_LEVEL_INTERRUPT	1
+
+#define RX_TIME_OUT		ENABLE
+#define RX_ERROR_STATE_INT_ENB	ENABLE
+#define LOOP_BACK		DISABLE
+#define BREAK_SIGNAL		DISABLE
+
+#define TX_MODE_DISABLED	0X00
+#define TX_MODE_IRQ_OR_POLL	0X01
+#define TX_MODE_DMA		0X02
+
+#define RX_MODE_DISABLED	0X00
+#define RX_MODE_IRQ_OR_POLL	0X01
+#define RX_MODE_DMA		0X02
+
+#define UCON_VAL		((TX_LEVEL_INTERRUPT << 9) \
+				| (RX_LEVEL_INTERRUPT << 8) \
+				| (RX_TIME_OUT << 7) \
+				| (RX_ERROR_STATE_INT_ENB << 6) \
+				| (LOOP_BACK << 5) \
+				| (BREAK_SIGNAL << 4) \
+				| (TX_MODE_IRQ_OR_POLL << 2) \
+				| (RX_MODE_IRQ_OR_POLL << 0))
+
+/*
+ * UFCON: UART FIFO Control Value
+ * Tx FIFO Trigger LEVEL: 2 Bytes (001)
+ * Rx FIFO Trigger LEVEL: 2 Bytes (001)
+ * Tx Fifo Reset: No
+ * Rx Fifo Reset: No
+ * FIFO Enable: Yes
+ */
+#define TX_FIFO_TRIGGER_LEVEL_0_BYTES	0x00
+#define TX_FIFO_TRIGGER_LEVEL_2_BYTES	0x1
+#define TX_FIFO_TRIGGER_LEVEL_4_BYTES	0x2
+#define TX_FIFO_TRIGGER_LEVEL_6_BYTES	0x3
+#define TX_FIFO_TRIGGER_LEVEL_8_BYTES	0x4
+#define TX_FIFO_TRIGGER_LEVEL_10_BYTES	0x5
+#define TX_FIFO_TRIGGER_LEVEL_12_BYTES	0x6
+#define TX_FIFO_TRIGGER_LEVEL_14_BYTES	0x7
+
+#define RX_FIFO_TRIGGER_LEVEL_2_BYTES	0x0
+#define RX_FIFO_TRIGGER_LEVEL_4_BYTES	0x1
+#define RX_FIFO_TRIGGER_LEVEL_6_BYTES	0x2
+#define RX_FIFO_TRIGGER_LEVEL_8_BYTES	0x3
+#define RX_FIFO_TRIGGER_LEVEL_10_BYTES	0x4
+#define RX_FIFO_TRIGGER_LEVEL_12_BYTES	0x5
+#define RX_FIFO_TRIGGER_LEVEL_14_BYTES	0x6
+#define RX_FIFO_TRIGGER_LEVEL_16_BYTES	0x7
+
+#define TX_FIFO_TRIGGER_LEVEL		TX_FIFO_TRIGGER_LEVEL_2_BYTES
+#define RX_FIFO_TRIGGER_LEVEL		RX_FIFO_TRIGGER_LEVEL_4_BYTES
+#define TX_FIFO_RESET			DISABLE
+#define RX_FIFO_RESET			DISABLE
+#define FIFO_ENABLE			ENABLE
+#define UFCON_VAL			((TX_FIFO_TRIGGER_LEVEL << 8) \
+					| (RX_FIFO_TRIGGER_LEVEL << 4) \
+					| (TX_FIFO_RESET << 2) \
+					| (RX_FIFO_RESET << 1) \
+					| (FIFO_ENABLE << 0))
+/*
+ * Baud Rate Division Value
+ * 115200 BAUD:
+ * UBRDIV_VAL = SCLK_UART/((115200 * 16) - 1)
+ * UBRDIV_VAL = (800 MHz)/((115200 * 16) - 1)
+ */
+#define UBRDIV_VAL		0x35
+
+/*
+ * Fractional Part of Baud Rate Divisor:
+ * 115200 BAUD:
+ * UBRFRACVAL = ((((SCLK_UART*10/(115200*16) -10))%10)*16/10)
+ * UBRFRACVAL = ((((800MHz*10/(115200*16) -10))%10)*16/10)
+ */
+#define UFRACVAL_VAL		0x4
+
+/*
+ * TZPC Register Value :
+ * R0SIZE: 0x0 : Size of secured ram
+ */
+#define R0SIZE			0x0
+
+/*
+ * TZPC Decode Protection Register Value :
+ * DECPROTXSET: 0xFF : Set Decode region to non-secure
+ */
+#define DECPROTXSET		0xFF
+#endif
diff --git a/boards.cfg b/boards.cfg
index 5cfaa78..1009f1c 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -165,6 +165,7 @@ omap4_panda                  arm         armv7       panda               ti
 omap4_sdp4430                arm         armv7       sdp4430             ti             omap4
 s5p_goni                     arm         armv7       goni                samsung        s5pc1xx
 smdkc100                     arm         armv7       smdkc100            samsung        s5pc1xx
+origen			     arm	 armv7	     origen		 samsung	s5pc2xx
 s5pc210_universal            arm         armv7       universal_c210      samsung        s5pc2xx
 smdkv310		     arm	 armv7	     smdkv310		 samsung	s5pc2xx
 harmony                      arm         armv7       harmony             nvidia         tegra2
diff --git a/include/configs/origen.h b/include/configs/origen.h
new file mode 100644
index 0000000..e8252cc
--- /dev/null
+++ b/include/configs/origen.h
@@ -0,0 +1,160 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG ORIGEN (S5PV310) board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_SAMSUNG			1	/* SAMSUNG core */
+#define CONFIG_S5P			1	/* S5P Family */
+#define CONFIG_S5PC210			1	/* which is in a S5PC210 SoC */
+#define CONFIG_ORIGEN			1	/* working with ORIGEN*/
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Keep L2 Cache Disabled */
+#define CONFIG_L2_OFF			1
+#define CONFIG_SYS_DCACHE_OFF		1
+
+#define CONFIG_SYS_SDRAM_BASE		0x40000000
+#define CONFIG_SYS_TEXT_BASE		0x43E00000
+
+/* input clock of PLL: ORIGEN has 24MHz input clock */
+#define CONFIG_SYS_CLK_FREQ		24000000
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_EDITING
+
+/* MACH_TYPE_ORIGEN macro will be removed once added to mach-types */
+#define MACH_TYPE_ORIGEN		3455
+#define CONFIG_MACH_TYPE		MACH_TYPE_ORIGEN
+
+/* Power Down Modes */
+#define S5P_CHECK_SLEEP			0x00000BAD
+#define S5P_CHECK_DIDLE			0xBAD00000
+#define S5P_CHECK_LPA			0xABAD0000
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (1 << 20))
+
+/* select serial console configuration */
+#define CONFIG_SERIAL_MULTI		1
+#define CONFIG_SERIAL2			1	/* use SERIAL 2 */
+#define CONFIG_BAUDRATE			115200
+#define S5PC210_DEFAULT_UART_OFFSET	0x020000
+
+/* SD/MMC configuration */
+#define CONFIG_GENERIC_MMC		1
+#define CONFIG_MMC			1
+#define CONFIG_S5P_MMC			1
+
+/* PWM */
+#define CONFIG_PWM			1
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Command definition*/
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#define CONFIG_BOOTCOMMAND	"fatload mmc 0 40007000 uImage; bootm 40007000"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_PROMPT		"ORIGEN # "
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size*/
+#define CONFIG_SYS_PBSIZE		384	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC2,115200n8\0"
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x6000000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x3E00000)
+
+#define CONFIG_SYS_HZ			1000
+
+/* valid baudrates */
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+/* Stack sizes */
+#define CONFIG_STACKSIZE		(256 << 10)	/* 256KB */
+
+/* ORIGEN has 4 bank of DRAM */
+#define CONFIG_NR_DRAM_BANKS	4
+#define SDRAM_BANK_SIZE		(256UL << 20UL)	/* 256 MB */
+#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE
+#define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_2		(CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
+#define PHYS_SDRAM_2_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_3		(CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_3_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_4		(CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_4_SIZE	SDRAM_BANK_SIZE
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH		1
+#undef CONFIG_CMD_IMLS
+#define CONFIG_IDENT_STRING		" for ORIGEN"
+
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ		(4*1024)	/* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ		(4*1024)	/* FIQ stack */
+#endif
+
+#define CONFIG_CLK_1000_400_200
+
+/* MIU (Memory Interleaving Unit) */
+#define CONFIG_MIU_2BIT_21_7_INTERLEAVED
+
+#define CONFIG_ENV_IS_IN_MMC		1
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#define CONFIG_ENV_SIZE			(16 << 10)	/* 16 KB */
+#define RESERVE_BLOCK_SIZE		(512)
+#define BL1_SIZE			(16 << 10) /*16 K reserved for BL1*/
+#define CONFIG_ENV_OFFSET		(RESERVE_BLOCK_SIZE + BL1_SIZE)
+#define CONFIG_DOS_PARTITION		1
+
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE)
+#endif	/* __CONFIG_H */
-- 
1.7.4.1



More information about the U-Boot mailing list