[U-Boot] [PATCH v2 03/16] ARM: remove broken "edb93xx" boards
Wolfgang Denk
wd at denx.de
Fri Aug 26 14:25:35 CEST 2011
Remove edb9301, edb9302, edb9302a, edb9307, edb9307a, edb9312,
edb9315 and edb9315a boards.
Signed-off-by: Wolfgang Denk <wd at denx.de>
---
MAKEALL | 8 --
Makefile | 10 --
board/edb93xx/Makefile | 50 --------
board/edb93xx/config.mk | 33 -----
board/edb93xx/early_udelay.h | 34 ------
board/edb93xx/edb93xx.c | 110 -----------------
board/edb93xx/flash_cfg.c | 38 ------
board/edb93xx/pll_cfg.c | 58 ---------
board/edb93xx/pll_cfg.h | 72 -----------
board/edb93xx/sdram_cfg.c | 146 -----------------------
board/edb93xx/sdram_cfg.h | 144 ----------------------
doc/README.scrapyard | 8 ++
include/configs/edb93xx.h | 269 ------------------------------------------
13 files changed, 8 insertions(+), 972 deletions(-)
delete mode 100644 board/edb93xx/Makefile
delete mode 100644 board/edb93xx/config.mk
delete mode 100644 board/edb93xx/early_udelay.h
delete mode 100644 board/edb93xx/edb93xx.c
delete mode 100644 board/edb93xx/flash_cfg.c
delete mode 100644 board/edb93xx/pll_cfg.c
delete mode 100644 board/edb93xx/pll_cfg.h
delete mode 100644 board/edb93xx/sdram_cfg.c
delete mode 100644 board/edb93xx/sdram_cfg.h
delete mode 100644 include/configs/edb93xx.h
diff --git a/MAKEALL b/MAKEALL
index 63315fb..289cd8b 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -318,14 +318,6 @@ LIST_ARM9=" \
aspenite \
da830evm \
da850evm \
- edb9301 \
- edb9302 \
- edb9302a \
- edb9307 \
- edb9307a \
- edb9312 \
- edb9315 \
- edb9315a \
edminiv2 \
guruplug \
imx27lite \
diff --git a/Makefile b/Makefile
index 676dc29..6cafb99 100644
--- a/Makefile
+++ b/Makefile
@@ -851,16 +851,6 @@ tx25_config : unconfig
@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
@$(MKCONFIG) $@ arm arm926ejs tx25 karo mx25
-edb9301_config \
-edb9302_config \
-edb9302a_config \
-edb9307_config \
-edb9307a_config \
-edb9312_config \
-edb9315_config \
-edb9315a_config: unconfig
- @$(MKCONFIG) -n $@ -t $(@:_config=) edb93xx arm arm920t edb93xx - ep93xx
-
#########################################################################
## XScale Systems
#########################################################################
diff --git a/board/edb93xx/Makefile b/board/edb93xx/Makefile
deleted file mode 100644
index dcaed06..0000000
--- a/board/edb93xx/Makefile
+++ /dev/null
@@ -1,50 +0,0 @@
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS := edb93xx.o flash_cfg.o pll_cfg.o sdram_cfg.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(call cmd_link_o_target, $(OBJS) $(SOBJS))
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak .depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/edb93xx/config.mk b/board/edb93xx/config.mk
deleted file mode 100644
index fab59ef..0000000
--- a/board/edb93xx/config.mk
+++ /dev/null
@@ -1,33 +0,0 @@
-LDSCRIPT := $(SRCTREE)/arch/arm/cpu/arm920t/ep93xx/u-boot.lds
-
-ifdef CONFIG_EDB9301
-CONFIG_SYS_TEXT_BASE = 0x05700000
-endif
-
-ifdef CONFIG_EDB9302
-CONFIG_SYS_TEXT_BASE = 0x05700000
-endif
-
-ifdef CONFIG_EDB9302A
-CONFIG_SYS_TEXT_BASE = 0xc5700000
-endif
-
-ifdef CONFIG_EDB9307
-CONFIG_SYS_TEXT_BASE = 0x01f00000
-endif
-
-ifdef CONFIG_EDB9307A
-CONFIG_SYS_TEXT_BASE = 0xc1f00000
-endif
-
-ifdef CONFIG_EDB9312
-CONFIG_SYS_TEXT_BASE = 0x01f00000
-endif
-
-ifdef CONFIG_EDB9315
-CONFIG_SYS_TEXT_BASE = 0x01f00000
-endif
-
-ifdef CONFIG_EDB9315A
-CONFIG_SYS_TEXT_BASE = 0xc1f00000
-endif
diff --git a/board/edb93xx/early_udelay.h b/board/edb93xx/early_udelay.h
deleted file mode 100644
index 185283d..0000000
--- a/board/edb93xx/early_udelay.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * Copyright (C) 2009 Matthias Kaehlcke <matthias at kaehlcke.net>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-/* delay execution before timers are initialized */
-static inline void early_udelay(uint32_t usecs)
-{
- /* loop takes 4 cycles at 5.0ns (fastest case, running at 200MHz) */
- register uint32_t loops = usecs * (1000 / 20);
-
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
diff --git a/board/edb93xx/edb93xx.c b/board/edb93xx/edb93xx.c
deleted file mode 100644
index dde30ff..0000000
--- a/board/edb93xx/edb93xx.c
+++ /dev/null
@@ -1,110 +0,0 @@
-/*
- * Copyright (C) 2009 Matthias Kaehlcke <matthias at kaehlcke.net>
- *
- * (C) Copyright 2002 2003
- * Network Audio Technologies, Inc. <www.netaudiotech.com>
- * Adam Bezanson <bezanson at netaudiotech.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/arch/ep93xx.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define MAX_BANK_SIZE 0x04000000 /* 64 MB */
-
-static ulong const bank_addr[CONFIG_NR_DRAM_BANKS] = {
- PHYS_SDRAM_1,
-#ifdef PHYS_SDRAM_2
- PHYS_SDRAM_2,
-#endif
-#ifdef PHYS_SDRAM_3
- PHYS_SDRAM_3,
-#endif
-#ifdef PHYS_SDRAM_4
- PHYS_SDRAM_4
-#endif
-};
-
-int board_init(void)
-{
- struct syscon_regs *syscon = (struct syscon_regs *)SYSCON_BASE;
-
- icache_enable();
-
-#ifdef USE_920T_MMU
- dcache_enable();
-#endif
-
- /*
- * set UARTBAUD bit to drive UARTs with 14.7456MHz instead of
- * 14.7456/2 MHz
- */
- uint32_t value = readl(&syscon->pwrcnt);
- value |= SYSCON_PWRCNT_UART_BAUD;
- writel(value, &syscon->pwrcnt);
-
- /* Enable the uart in devicecfg */
- value = readl(&syscon->devicecfg);
- value |= 1<<18 /* U1EN */;
- writel(0xAA, &syscon->sysswlock);
- writel(value, &syscon->devicecfg);
-
- /* Machine number, as defined in linux/arch/arm/tools/mach-types */
- gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- /* We have a console */
- gd->have_console = 1;
-
- return 0;
-}
-
-int board_eth_init(bd_t *bd)
-{
- return ep93xx_eth_initialize(0, MAC_BASE);
-}
-
-int dram_init(void)
-{
- unsigned int *src, *dst;
- int i;
-
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
- const ulong bank_size = get_ram_size((long *)bank_addr[i],
- MAX_BANK_SIZE);
- if (bank_size) {
- gd->bd->bi_dram[i].start = bank_addr[i];
- gd->bd->bi_dram[i].size = bank_size;
- }
- }
-
- /* copy exception vectors */
- src = (unsigned int *)_armboot_start;
- dst = (unsigned int *)PHYS_SDRAM_1;
- memcpy(dst, src, 16 * sizeof(unsigned int));
-
- return 0;
-}
diff --git a/board/edb93xx/flash_cfg.c b/board/edb93xx/flash_cfg.c
deleted file mode 100644
index a4c2048..0000000
--- a/board/edb93xx/flash_cfg.c
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * Flash setup for Cirrus edb93xx boards
- *
- * Copyright (C) 2009 Matthias Kaehlcke <matthias at kaehlcke.net>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/arch/ep93xx.h>
-#include <asm/io.h>
-
-#define SMC_BCR6_VALUE (2 << SMC_BCR_IDCY_SHIFT | 5 << SMC_BCR_WST1_SHIFT | \
- SMC_BCR_BLE | 2 << SMC_BCR_WST2_SHIFT | \
- 1 << SMC_BCR_MW_SHIFT)
-
-void flash_cfg(void)
-{
- struct smc_regs *smc = (struct smc_regs *)SMC_BASE;
-
- writel(SMC_BCR6_VALUE, &smc->bcr6);
-}
diff --git a/board/edb93xx/pll_cfg.c b/board/edb93xx/pll_cfg.c
deleted file mode 100644
index a687af0..0000000
--- a/board/edb93xx/pll_cfg.c
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * PLL setup for Cirrus edb93xx boards
- *
- * Copyright (C) 2009 Matthias Kaehlcke <matthias at kaehlcke.net>
- *
- * Copyright (C) 2006 Dominic Rath <Dominic.Rath at gmx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include "pll_cfg.h"
-#include "early_udelay.h"
-
-void pll_cfg(void)
-{
- struct syscon_regs *syscon = (struct syscon_regs *)SYSCON_BASE;
-
- /* setup PLL1 */
- writel(CLKSET1_VAL, &syscon->clkset1);
-
- /*
- * flush the pipeline
- * writing to CLKSET1 causes the EP93xx to enter standby for between
- * 8 ms to 16 ms, until PLL1 stabilizes
- */
- asm("nop");
- asm("nop");
- asm("nop");
- asm("nop");
- asm("nop");
-
- /* setup PLL2 */
- writel(CLKSET2_VAL, &syscon->clkset2);
-
- /*
- * the user's guide recommends to wait at least 1 ms for PLL2 to
- * stabilize
- */
- early_udelay(1000);
-}
diff --git a/board/edb93xx/pll_cfg.h b/board/edb93xx/pll_cfg.h
deleted file mode 100644
index 0b6f469..0000000
--- a/board/edb93xx/pll_cfg.h
+++ /dev/null
@@ -1,72 +0,0 @@
-/*
- * PLL register values for Cirrus edb93xx boards
- *
- * Copyright (C) 2009 Matthias Kaehlcke <matthias at kaehlcke.net>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <asm/arch/ep93xx.h>
-
-#if defined(CONFIG_EDB9301) || defined(CONFIG_EDB9302) || \
- defined(CONFIG_EDB9302A)
-/*
- * fclk_div: 2, nbyp1: 1, hclk_div: 5, pclk_div: 2
- * pll1_x1: 294912000.000000, pll1_x2ip: 36864000.000000,
- * pll1_x2: 331776000.000000, pll1_out: 331776000.000000
- */
-#define CLKSET1_VAL (7 << SYSCON_CLKSET_PLL_X2IPD_SHIFT | \
- 8 << SYSCON_CLKSET_PLL_X2FBD2_SHIFT | \
- 19 << SYSCON_CLKSET_PLL_X1FBD1_SHIFT | \
- 1 << SYSCON_CLKSET1_PCLK_DIV_SHIFT | \
- 3 << SYSCON_CLKSET1_HCLK_DIV_SHIFT | \
- SYSCON_CLKSET1_NBYP1 | \
- 1 << SYSCON_CLKSET1_FCLK_DIV_SHIFT)
-#elif defined(CONFIG_EDB9307) || defined(CONFIG_EDB9307A) || \
- defined CONFIG_EDB9312 || defined(CONFIG_EDB9315) || \
- defined(CONFIG_EDB9315A)
-/*
- * fclk_div: 2, nbyp1: 1, hclk_div: 4, pclk_div: 2
- * pll1_x1: 3096576000.000000, pll1_x2ip: 129024000.000000,
- * pll1_x2: 3999744000.000000, pll1_out: 1999872000.000000
- */
-#define CLKSET1_VAL (23 << SYSCON_CLKSET_PLL_X2IPD_SHIFT | \
- 30 << SYSCON_CLKSET_PLL_X2FBD2_SHIFT | \
- 20 << SYSCON_CLKSET_PLL_X1FBD1_SHIFT | \
- 1 << SYSCON_CLKSET1_PCLK_DIV_SHIFT | \
- 2 << SYSCON_CLKSET1_HCLK_DIV_SHIFT | \
- SYSCON_CLKSET1_NBYP1 | \
- 1 << SYSCON_CLKSET1_FCLK_DIV_SHIFT)
-#else
-#error "Undefined board"
-#endif
-
-/*
- * usb_div: 4, nbyp2: 1, pll2_en: 1
- * pll2_x1: 368640000.000000, pll2_x2ip: 15360000.000000,
- * pll2_x2: 384000000.000000, pll2_out: 192000000.000000
- */
-#define CLKSET2_VAL (23 << SYSCON_CLKSET_PLL_X2IPD_SHIFT | \
- 24 << SYSCON_CLKSET_PLL_X2FBD2_SHIFT | \
- 24 << SYSCON_CLKSET_PLL_X1FBD1_SHIFT | \
- 1 << SYSCON_CLKSET_PLL_PS_SHIFT | \
- SYSCON_CLKSET2_PLL2_EN | \
- SYSCON_CLKSET2_NBYP2 | \
- 3 << SYSCON_CLKSET2_USB_DIV_SHIFT)
diff --git a/board/edb93xx/sdram_cfg.c b/board/edb93xx/sdram_cfg.c
deleted file mode 100644
index 440ad11..0000000
--- a/board/edb93xx/sdram_cfg.c
+++ /dev/null
@@ -1,146 +0,0 @@
-/*
- * Copyright (C) 2009, 2010 Matthias Kaehlcke <matthias at kaehlcke.net>
- *
- * Copyright (C) 2006 Dominic Rath <Dominic.Rath at gmx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <asm/io.h>
-#include "sdram_cfg.h"
-#include "early_udelay.h"
-
-#define PROGRAM_MODE_REG(bank) (*(volatile uint32_t *) \
- (SDRAM_BASE_ADDR | SDRAM_BANK_SEL_##bank | SDRAM_MODE_REG_VAL))
-
-#define PRECHARGE_BANK(bank) (*(volatile uint32_t *) \
- (SDRAM_BASE_ADDR | SDRAM_BANK_SEL_##bank)) = 0
-
-static void precharge_all_banks(void);
-static void setup_refresh_timer(void);
-static void program_mode_registers(void);
-
-void sdram_cfg(void)
-{
- struct sdram_regs *sdram = (struct sdram_regs *)SDRAM_BASE;
-
- writel(SDRAM_DEVCFG_VAL, &sdram->SDRAM_DEVCFG_REG);
-
- /* Issue continous NOP commands */
- writel(GLCONFIG_INIT | GLCONFIG_MRS | GLCONFIG_CKE, &sdram->glconfig);
-
- early_udelay(200);
-
- precharge_all_banks();
-
- setup_refresh_timer();
-
- program_mode_registers();
-
- /* Select normal operation mode */
- writel(GLCONFIG_CKE, &sdram->glconfig);
-}
-
-static void precharge_all_banks(void)
-{
- struct sdram_regs *sdram = (struct sdram_regs *)SDRAM_BASE;
-
- /* Issue PRECHARGE ALL commands */
- writel(GLCONFIG_INIT | GLCONFIG_CKE, &sdram->glconfig);
-
- /*
- * Errata of most EP93xx revisions say that PRECHARGE ALL isn't always
- * issued
- *
- * Cirrus proposes a workaround which consists in performing a read from
- * each bank to force the precharge. This causes some boards to hang.
- * Writing to the SDRAM banks instead of reading has the same
- * side-effect (the SDRAM controller issues the necessary precharges),
- * but is known to work on all supported boards
- */
-
- PRECHARGE_BANK(0);
-
-#if (CONFIG_NR_DRAM_BANKS >= 2)
- PRECHARGE_BANK(1);
-#endif
-
-#if (CONFIG_NR_DRAM_BANKS >= 3)
- PRECHARGE_BANK(2);
-#endif
-
-#if (CONFIG_NR_DRAM_BANKS == 4)
- PRECHARGE_BANK(3);
-#endif
-}
-
-static void setup_refresh_timer(void)
-{
- struct sdram_regs *sdram = (struct sdram_regs *)SDRAM_BASE;
-
- /* Load refresh timer with 10 to issue refresh every 10 cycles */
- writel(0x0a, &sdram->refrshtimr);
-
- /*
- * Wait at least 80 clock cycles to provide 8 refresh cycles
- * to all SDRAMs
- */
- early_udelay(1);
-
- /*
- * Program refresh timer with normal value
- * We need 8192 refresh cycles every 64ms
- * at 15ns (HCLK >= 66MHz) per cycle:
- * 64ms / 8192 = 7.8125us
- * 7.8125us / 15ns = 520 (0x208)
- */
- /*
- * TODO: redboot uses 0x1e0 for the slowest possible device
- * but i don't understand how this value is calculated
- */
- writel(0x208, &sdram->refrshtimr);
-}
-
-static void program_mode_registers(void)
-{
- struct sdram_regs *sdram = (struct sdram_regs *)SDRAM_BASE;
-
- /* Select mode register update mode */
- writel(GLCONFIG_MRS | GLCONFIG_CKE, &sdram->glconfig);
-
- /*
- * The mode registers are programmed by performing a read from each
- * SDRAM bank. The value of the address that is read defines the value
- * that is written into the mode register
- */
-
- PROGRAM_MODE_REG(0);
-
-#if (CONFIG_NR_DRAM_BANKS >= 2)
- PROGRAM_MODE_REG(1);
-#endif
-
-#if (CONFIG_NR_DRAM_BANKS >= 3)
- PROGRAM_MODE_REG(2);
-#endif
-
-#if (CONFIG_NR_DRAM_BANKS == 4)
- PROGRAM_MODE_REG(3);
-#endif
-}
diff --git a/board/edb93xx/sdram_cfg.h b/board/edb93xx/sdram_cfg.h
deleted file mode 100644
index 757b63c..0000000
--- a/board/edb93xx/sdram_cfg.h
+++ /dev/null
@@ -1,144 +0,0 @@
-/*
- * Copyright (C) 2009 Matthias Kaehlcke <matthias at kaehlcke.net>
- *
- * Copyright (C) 2006 Dominic Rath <Dominic.Rath at gmx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <asm/arch/ep93xx.h>
-
-#define SDRAM_BASE_ADDR PHYS_SDRAM_1
-
-#ifdef CONFIG_EDB93XX_SDCS0
-#define SDRAM_DEVCFG_REG devcfg0
-#elif defined(CONFIG_EDB93XX_SDCS3)
-#define SDRAM_DEVCFG_REG devcfg3
-#else
-#error "SDRAM bank configuration"
-#endif
-
-#if defined(CONFIG_EDB9301) || defined(CONFIG_EDB9302) || \
- defined(CONFIG_EDB9302A)
-/*
- * 1x Samsung K4S561632C-TC/L75 4M x 16bit x 4 banks SDRAM
- *
- * CLK cycle time min:
- * @ CAS latency = 3: 7.5ns
- * @ CAS latency = 2: 10ns
- * We're running at 66MHz (15ns cycle time) external bus speed (HCLK),
- * so it's safe to use CAS latency = 2
- *
- * RAS-to-CAS delay min:
- * 20ns
- * At 15ns cycle time, we use RAS-to-CAS delay = 2
- *
- * SROMLL = 1: Swap BA[1:0] with A[13:12], making the SDRAM appear
- * as four blocks of 8MB size, instead of eight blocks of 4MB size:
- *
- * EDB9301/EDB9302:
- *
- * 0x00000000 - 0x007fffff
- * 0x01000000 - 0x017fffff
- * 0x04000000 - 0x047fffff
- * 0x05000000 - 0x057fffff
- *
- *
- * EDB9302a:
- *
- * 0xc0000000 - 0xc07fffff
- * 0xc1000000 - 0xc17fffff
- * 0xc4000000 - 0xc47fffff
- * 0xc5000000 - 0xc57fffff
- *
- * BANKCOUNT = 1: This is a device with four banks
- */
-
-#define SDRAM_DEVCFG_VAL (SDRAM_DEVCFG_BANKCOUNT | \
- SDRAM_DEVCFG_SROMLL | \
- SDRAM_DEVCFG_CASLAT_2 | \
- SDRAM_DEVCFG_RASTOCAS_2 | \
- SDRAM_DEVCFG_EXTBUSWIDTH)
-
-/*
- * 16 bit ext. bus
- *
- * A[22:09] is output as SYA[13:0]
- * CAS latency: 2
- * Burst type: sequential
- * Burst length: 8 (required for 16 bit ext. bus)
- * SYA[13:0] = 0x0023
- */
-#define SDRAM_MODE_REG_VAL 0x4600
-
-#define SDRAM_BANK_SEL_0 0x00000000 /* A[22:21] = b00 */
-#define SDRAM_BANK_SEL_1 0x00200000 /* A[22:21] = b01 */
-#define SDRAM_BANK_SEL_2 0x00400000 /* A[22:21] = b10 */
-#define SDRAM_BANK_SEL_3 0x00600000 /* A[22:21] = b11 */
-
-#elif defined(CONFIG_EDB9307) || defined(CONFIG_EDB9307A) || \
- defined CONFIG_EDB9312 || defined(CONFIG_EDB9315) || \
- defined(CONFIG_EDB9315A)
-/*
- * 2x Samsung K4S561632C-TC/L75 4M x 16bit x 4 banks SDRAM
- *
- * CLK cycle time min:
- * @ CAS latency = 3: 7.5ns
- * @ CAS latency = 2: 10ns
- * We're running at 100MHz (10ns cycle time) external bus speed (HCLK),
- * so it's safe to use CAS latency = 2
- *
- * RAS-to-CAS delay min:
- * 20ns
- * At 10ns cycle time, we use RAS-to-CAS delay = 2
- *
- * EDB9307, EDB9312, EDB9315:
- *
- * 0x00000000 - 0x01ffffff
- * 0x04000000 - 0x05ffffff
- *
- *
- * EDB9307a, EDB9315a:
- *
- * 0xc0000000 - 0xc1ffffff
- * 0xc4000000 - 0xc5ffffff
- */
-
-#define SDRAM_DEVCFG_VAL (SDRAM_DEVCFG_BANKCOUNT | \
- SDRAM_DEVCFG_SROMLL | \
- SDRAM_DEVCFG_CASLAT_2 | \
- SDRAM_DEVCFG_RASTOCAS_2)
-
-/*
- * 32 bit ext. bus
- *
- * A[23:10] is output as SYA[13:0]
- * CAS latency: 2
- * Burst type: sequential
- * Burst length: 4
- * SYA[13:0] = 0x0022
- */
-#define SDRAM_MODE_REG_VAL 0x8800
-
-#define SDRAM_BANK_SEL_0 0x00000000 /* A[23:22] = b00 */
-#define SDRAM_BANK_SEL_1 0x00400000 /* A[23:22] = b01 */
-#define SDRAM_BANK_SEL_2 0x00800000 /* A[23:22] = b10 */
-#define SDRAM_BANK_SEL_3 0x00c00000 /* A[23:22] = b11 */
-#endif
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index e12208c..7bd445c 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,6 +11,14 @@ easily if here is something they might want to dig for...
Board Arch CPU removed Commit last known maintainer/contact
=============================================================================
+edb9301 arm arm920t - 2011-07-17
+edb9302 arm arm920t - 2011-07-17
+edb9302a arm arm920t - 2011-07-17
+edb9307 arm arm920t - 2011-07-17
+edb9307a arm arm920t - 2011-07-17
+edb9312 arm arm920t - 2011-07-17
+edb9315 arm arm920t - 2011-07-17
+edb9315a arm arm920t - 2011-07-17
B2 arm s3c44b0 - 2011-07-16 Andrea Scian <andrea.scian at dave-tech.it>
armadillo arm arm720t - 2011-07-16 Rowel Atienza <rowel at diwalabs.com>
trab arm S3C2400 - 2011-05-01 Gary Jennejohn <garyj at denx.de>
diff --git a/include/configs/edb93xx.h b/include/configs/edb93xx.h
deleted file mode 100644
index 19b7632..0000000
--- a/include/configs/edb93xx.h
+++ /dev/null
@@ -1,269 +0,0 @@
-/*
- * U-boot - Configuration file for Cirrus Logic EDB93xx boards
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#ifdef CONFIG_edb9301
-#define CONFIG_EDB9301
-#elif defined(CONFIG_edb9302)
-#define CONFIG_EDB9302
-#elif defined(CONFIG_edb9302a)
-#define CONFIG_EDB9302A
-#elif defined(CONFIG_edb9307)
-#define CONFIG_EDB9307
-#elif defined(CONFIG_edb9307a)
-#define CONFIG_EDB9307A
-#elif defined(CONFIG_edb9312)
-#define CONFIG_EDB9312
-#elif defined(CONFIG_edb9315)
-#define CONFIG_EDB9315
-#elif defined(CONFIG_edb9315a)
-#define CONFIG_EDB9315A
-#else
-#error "no board defined"
-#endif
-
-/* Initial environment and monitor configuration options. */
-#define CONFIG_BOOTDELAY 2
-#define CONFIG_CMDLINE_TAG 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_BOOTARGS "root=/dev/nfs console=ttyAM0,115200 ip=dhcp"
-#define CONFIG_BOOTFILE "edb93xx.img"
-
-#define CONFIG_SYS_HUSH_PARSER 1
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-#ifdef CONFIG_EDB9301
-#define CONFIG_EP9301
-#define CONFIG_MACH_TYPE MACH_TYPE_EDB9301
-#define CONFIG_SYS_PROMPT "EDB9301> "
-#define CONFIG_ENV_SECT_SIZE 0x00020000
-#elif defined(CONFIG_EDB9302)
-#define CONFIG_EP9302
-#define CONFIG_MACH_TYPE MACH_TYPE_EDB9302
-#define CONFIG_SYS_PROMPT "EDB9302> "
-#define CONFIG_ENV_SECT_SIZE 0x00020000
-#elif defined(CONFIG_EDB9302A)
-#define CONFIG_EP9302
-#define CONFIG_MACH_TYPE MACH_TYPE_EDB9302A
-#define CONFIG_SYS_PROMPT "EDB9302A> "
-#define CONFIG_ENV_SECT_SIZE 0x00020000
-#elif defined(CONFIG_EDB9307)
-#define CONFIG_EP9307
-#define CONFIG_MACH_TYPE MACH_TYPE_EDB9307
-#define CONFIG_SYS_PROMPT "EDB9307> "
-#define CONFIG_ENV_SECT_SIZE 0x00040000
-#elif defined(CONFIG_EDB9307A)
-#define CONFIG_EP9307
-#define CONFIG_MACH_TYPE MACH_TYPE_EDB9307A
-#define CONFIG_SYS_PROMPT "EDB9307A> "
-#define CONFIG_ENV_SECT_SIZE 0x00040000
-#elif defined(CONFIG_EDB9312)
-#define CONFIG_EP9312
-#define CONFIG_MACH_TYPE MACH_TYPE_EDB9312
-#define CONFIG_SYS_PROMPT "EDB9312> "
-#define CONFIG_ENV_SECT_SIZE 0x00040000
-#elif defined(CONFIG_EDB9315)
-#define CONFIG_EP9315
-#define CONFIG_MACH_TYPE MACH_TYPE_EDB9315
-#define CONFIG_SYS_PROMPT "EDB9315> "
-#define CONFIG_ENV_SECT_SIZE 0x00040000
-#elif defined(CONFIG_EDB9315A)
-#define CONFIG_EP9315
-#define CONFIG_MACH_TYPE MACH_TYPE_EDB9315A
-#define CONFIG_SYS_PROMPT "EDB9315A> "
-#define CONFIG_ENV_SECT_SIZE 0x00040000
-#else
-#error "no board defined"
-#endif
-
-/* High-level configuration options */
-#define CONFIG_ARM920T 1 /* This is an ARM920T core... */
-#define CONFIG_EP93XX 1 /* in a Cirrus Logic 93xx SoC */
-
-#define CONFIG_SYS_CLK_FREQ 14745600 /* EP93xx has a 14.7456 clock */
-#define CONFIG_SYS_HZ 1000 /* decr freq: 1 ms ticks */
-#undef CONFIG_USE_IRQ /* Don't need IRQ/FIQ */
-
-/* Monitor configuration */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_XIMG
-
-#undef CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_JFFS2
-
-#define CONFIG_SYS_LONGHELP /* Enable "long" help in mon */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
-/* Print buffer size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-/* Boot argument buffer size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */
-
-/* Serial port hardware configuration */
-#define CONFIG_PL010_SERIAL
-#define CONFIG_CONS_INDEX 0
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
-#define CONFIG_SYS_SERIAL0 0x808C0000
-#define CONFIG_SYS_SERIAL1 0x808D0000
-#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \
- (void *)CONFIG_SYS_SERIAL1}
-
-/* Status LED */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED 1
-#define STATUS_LED_GREEN 0
-#define STATUS_LED_RED 1
-/* Green */
-#define STATUS_LED_BIT STATUS_LED_GREEN
-#define STATUS_LED_STATE STATUS_LED_ON
-#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-/* Red */
-#define STATUS_LED_BIT1 STATUS_LED_RED
-#define STATUS_LED_STATE1 STATUS_LED_OFF
-#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
-/* Optional value */
-#define STATUS_LED_BOOT STATUS_LED_BIT
-
-/* Network hardware configuration */
-#define CONFIG_DRIVER_EP93XX_MAC
-#define CONFIG_MII_SUPPRESS_PREAMBLE
-#define CONFIG_MII
-#define CONFIG_PHY_ADDR 1
-#define CONFIG_NET_MULTI
-#undef CONFIG_NETCONSOLE
-
-/* SDRAM configuration */
-#if defined(CONFIG_EDB9301) || defined(CONFIG_EDB9302)
-/*
- * EDB9301/2 has 4 banks of SDRAM consisting of 1x Samsung K4S561632E-TC75
- * 256 Mbit SDRAM on a 16-bit data bus, for a total of 32MB of SDRAM. We set
- * the SROMLL bit on the processor, resulting in this non-contiguous memory map.
- */
-#define CONFIG_NR_DRAM_BANKS 4
-#define PHYS_SDRAM_1 0x00000000
-#define PHYS_SDRAM_SIZE_1 0x00800000
-#define PHYS_SDRAM_2 0x01000000
-#define PHYS_SDRAM_SIZE_2 0x00800000
-#define PHYS_SDRAM_3 0x04000000
-#define PHYS_SDRAM_SIZE_3 0x00800000
-#define PHYS_SDRAM_4 0x05000000
-#define PHYS_SDRAM_SIZE_4 0x00800000
-#define CONFIG_EDB93XX_SDCS3
-#define CONFIG_SYS_MEMTEST_START 0x00100000
-#define CONFIG_SYS_MEMTEST_END 0x007fffff
-
-#elif defined(CONFIG_EDB9302A)
-/*
- * EDB9302a has 4 banks of SDRAM consisting of 1x Samsung K4S561632E-TC75
- * 256 Mbit SDRAM on a 16-bit data bus, for a total of 32MB of SDRAM. We set
- * the SROMLL bit on the processor, resulting in this non-contiguous memory map.
- */
-#define CONFIG_NR_DRAM_BANKS 4
-#define PHYS_SDRAM_1 0xc0000000
-#define PHYS_SDRAM_SIZE_1 0x00800000
-#define PHYS_SDRAM_2 0xc1000000
-#define PHYS_SDRAM_SIZE_2 0x00800000
-#define PHYS_SDRAM_3 0xc4000000
-#define PHYS_SDRAM_SIZE_3 0x00800000
-#define PHYS_SDRAM_4 0xc5000000
-#define PHYS_SDRAM_SIZE_4 0x00800000
-#define CONFIG_EDB93XX_SDCS0
-#define CONFIG_SYS_MEMTEST_START 0xc0100000
-#define CONFIG_SYS_MEMTEST_END 0xc07fffff
-
-#elif defined(CONFIG_EDB9307) || defined CONFIG_EDB9312 || \
- defined(CONFIG_EDB9315)
-/*
- * The EDB9307, EDB9312, and EDB9315 have 2 banks of SDRAM consisting of
- * 2x Samsung K4S561632E-TC75 256 Mbit on a 32-bit data bus, for a total of
- * 64 MB of SDRAM.
- */
-#define CONFIG_NR_DRAM_BANKS 2
-#define PHYS_SDRAM_1 0x00000000
-#define PHYS_SDRAM_SIZE_1 0x02000000
-#define PHYS_SDRAM_2 0x04000000
-#define PHYS_SDRAM_SIZE_2 0x02000000
-#define CONFIG_EDB93XX_SDCS3
-#define CONFIG_SYS_MEMTEST_START 0x00100000
-#define CONFIG_SYS_MEMTEST_END 0x01e00000
-
-#elif defined(CONFIG_EDB9307A) || defined(CONFIG_EDB9315A)
-/*
- * The EDB9307A and EDB9315A have 2 banks of SDRAM consisting of 2x Samsung
- * K4S561632E-TC75 256 Mbit on a 32-bit data bus, for a total of 64 MB of SDRAM.
- */
-#define CONFIG_NR_DRAM_BANKS 2
-#define PHYS_SDRAM_1 0xc0000000
-#define PHYS_SDRAM_SIZE_1 0x02000000
-#define PHYS_SDRAM_2 0xc4000000
-#define PHYS_SDRAM_SIZE_2 0x02000000
-#define CONFIG_EDB93XX_SDCS0
-#define CONFIG_SYS_MEMTEST_START 0xc0100000
-#define CONFIG_SYS_MEMTEST_END 0xc1e00000
-#endif
-
-/* Default load address */
-#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x01000000)
-
-/* Must match kernel config */
-#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
-
-/* Run-time memory allocatons */
-#define CONFIG_STACKSIZE (128 * 1024)
-
-#if defined(CONFIG_USE_IRQ)
-#define CONFIG_STACKSIZE_IRQ (4 * 1024)
-#define CONFIG_STACKSIZE_FIQ (4 * 1024)
-#endif
-
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
-
-/* -----------------------------------------------------------------------------
- * FLASH and environment organization
- *
- * The EDB9301 and EDB9302(a) have 1 bank of flash memory at 0x60000000
- * consisting of 1x Intel TE28F128J3C-150 128 Mbit flash on a 16-bit data bus,
- * for a total of 16 MB of CFI-compatible flash.
- *
- * The EDB9307(a), EDB9312, and EDB9315(a) have 1 bank of flash memory at
- * 0x60000000 consisting of 2x Micron MT28F128J3-12 128 Mbit flash on a 32-bit
- * data bus, for a total of 32 MB of CFI-compatible flash.
- *
- * EDB9301/02(a) EDB9307(a)/12/15(a)
- * 0x60000000 - 0x0003FFFF u-boot u-boot
- * 0x60040000 - 0x0005FFFF environment #1 environment #1
- * 0x60060000 - 0x0007FFFF environment #2 environment #1 (continued)
- * 0x60080000 - 0x0009FFFF unused environment #2
- * 0x600A0000 - 0x000BFFFF unused environment #2 (continued)
- * 0x600C0000 - 0x00FFFFFF unused unused
- * 0x61000000 - 0x01FFFFFF not present unused
- */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_MAX_FLASH_SECT 128
-
-#define PHYS_FLASH_1 0x60000000
-#define CONFIG_SYS_FLASH_BASE (PHYS_FLASH_1)
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
-
-#define CONFIG_ENV_OVERWRITE /* Vendor params unprotected */
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR 0x60040000
-
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-
-#endif /* !defined (__CONFIG_H) */
--
1.7.6
More information about the U-Boot
mailing list