[U-Boot] [RFC 2/3] omap: gpio: generic changes after changing API

[Sanjeev Premi]

This patch contains the generic changes required after
change to generic API in the previous patch.

Signed-off-by: Sanjeev Premi <premi at ti.com>
Cc: Sandeep Paulraj <s-paulraj at ti.com>
Cc: Igor Grinberg <grinberg at compulab.co.il>
Cc: Luca Ceresoli <luca.ceresoli at comelit.it>
Cc: Enric Balletbo i Serra <eballetbo at gmail.com>
Cc: Sunil Kumar <sunilsaini05 at gmail.com>
Cc: Shashi Ranjan <shashiranjanmca05 at gmail.com>
Cc: Nishanth Menon <nm at ti.com>
Cc: Steve Sakoman <steve at sakoman.com>

---

 These changes could have been merged with the previous
 patch, but kept changes to API separate from the usage.

 arch/arm/cpu/armv7/omap4/clocks.c |    4 ++--
 doc/README.omap3                  |   20 ++++++++++----------
 2 files changed, 12 insertions(+), 12 deletions(-)

diff --git a/arch/arm/cpu/armv7/omap4/clocks.c b/arch/arm/cpu/armv7/omap4/clocks.c
index eda960c..56cdbe4 100644
--- a/arch/arm/cpu/armv7/omap4/clocks.c
+++ b/arch/arm/cpu/armv7/omap4/clocks.c
@@ -481,8 +481,8 @@ static void do_scale_tps62361(u32 reg, u32 volt_mv)
 	 * VSEL1 is grounded on board. So the following selects
 	 * VSEL1 = 0 and VSEL0 = 1
 	 */
-	omap_set_gpio_direction(TPS62361_VSEL0_GPIO, 0);
-	omap_set_gpio_dataout(TPS62361_VSEL0_GPIO, 1);
+	gpio_direction_output(TPS62361_VSEL0_GPIO);
+	gpio_set_value(TPS62361_VSEL0_GPIO, 1);
 
 	temp = TPS62361_I2C_SLAVE_ADDR |
 	    (reg << PRM_VC_VAL_BYPASS_REGADDR_SHIFT) |
diff --git a/doc/README.omap3 b/doc/README.omap3
index 460950d..2a18133 100644
--- a/doc/README.omap3
+++ b/doc/README.omap3
@@ -98,24 +98,24 @@ gpio
 
 To set a bit :
 
-	if (!omap_request_gpio(N)) {
-		omap_set_gpio_direction(N, 0);
-		omap_set_gpio_dataout(N, 1);
+	if (!gpio_request(N, "")) {
+		gpio_direction_output(N);
+		gpio_set_value(N, 1);
 	}
 
 To clear a bit :
 
-	if (!omap_request_gpio(N)) {
-		omap_set_gpio_direction(N, 0);
-		omap_set_gpio_dataout(N, 0);
+	if (!gpio_request(N, "")) {
+		gpio_direction_output(N);
+		gpio_set_value(N, 0);
 	}
 
 To read a bit :
 
-	if (!omap_request_gpio(N)) {
-		omap_set_gpio_direction(N, 1);
-		val = omap_get_gpio_datain(N);
-		omap_free_gpio(N);
+	if (!gpio_request(N, "")) {
+		gpio_direction_input(N);
+		val = gpio_get_value(N);
+		gpio_free(N);
 	}
 	if (val)
 		printf("GPIO N is set\n");
-- 
1.7.0.4