[U-Boot] [PATCH v3] Add support for Bluewater Systems Snapper 9260 and 9G20 modules
Ryan Mallon
ryan at bluewatersys.com
Wed Feb 2 03:18:00 CET 2011
Add support for Bluewater Systems AT91 based Snapper 9260 and 9G20
single board computer modules. Includes NAND flash and Ethernet
support.
Signed-off-by: Ryan Mallon <ryan at bluewatersys.com>
---
Patches apply against the rework101229 branch of
git://git.denx.de/u-boot-atmel.git.
Builds and runs. Tested Ethernet and NAND booting.
Changes for v3:
- Replaced SZ_ macros with shifts
- Remove defined values from CONFIG_ defines
- Moved boards.cfg entry to correct place
- Added MAINTAINERS entry
Changes for v2:
- Updated for recent at91 changes
- Use CONFIG_AT91FAMILY in soft_i2c driver
- Fixed missing snapper9260.h config file
- Add config to boards.cfg not Makefile
- Removed config.mk (now in snapper9260.h)
MAINTAINERS | 5 +
board/bluewater/snapper9260/Makefile | 53 ++++++++
board/bluewater/snapper9260/snapper9260.c | 169 +++++++++++++++++++++++++
boards.cfg | 2 +
include/configs/snapper9260.h | 191 +++++++++++++++++++++++++++++
5 files changed, 420 insertions(+), 0 deletions(-)
create mode 100644 board/bluewater/snapper9260/Makefile
create mode 100644 board/bluewater/snapper9260/snapper9260.c
create mode 100644 include/configs/snapper9260.h
diff --git a/MAINTAINERS b/MAINTAINERS
index a5f0493..f8c1996 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -298,6 +298,11 @@ Dan Malek <dan at embeddedalley.com>
stxssa MPC85xx
stxxtc MPC8xx
+Ryan Mallon <ryan at bluewatersys.com>
+
+ snapper9260 ARM926EJS (AT91SAM9260 SoC)
+ snapper9g20 ARM926EJS (AT91SAM9G20 SoC)
+
Eran Man <eran at nbase.co.il>
EVB64260_750CX MPC750CX
diff --git a/board/bluewater/snapper9260/Makefile b/board/bluewater/snapper9260/Makefile
new file mode 100644
index 0000000..4fccdaa
--- /dev/null
+++ b/board/bluewater/snapper9260/Makefile
@@ -0,0 +1,53 @@
+#
+# (C) Copyright 2003-2008
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# (C) Copyright 2011 Bluewater Systems
+# Ryan Mallon <ryan at bluewatersys.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y += snapper9260.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/bluewater/snapper9260/snapper9260.c b/board/bluewater/snapper9260/snapper9260.c
new file mode 100644
index 0000000..6bb2ee0
--- /dev/null
+++ b/board/bluewater/snapper9260/snapper9260.c
@@ -0,0 +1,169 @@
+/*
+ * Bluewater Systems Snapper 9260/9G20 modules
+ *
+ * (C) Copyright 2011 Bluewater Systems
+ * Author: Andre Renaud <andre at bluewatersys.com>
+ * Author: Ryan Mallon <ryan at bluewatersys.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91sam9260_matrix.h>
+#include <asm/arch/at91sam9_smc.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/gpio.h>
+#include <net.h>
+#include <netdev.h>
+#include <i2c.h>
+#include <pca953x.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* IO Expander pins */
+#define IO_EXP_ETH_RESET (0 << 1)
+#define IO_EXP_ETH_POWER (1 << 1)
+
+static void macb_hw_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
+ struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
+ unsigned long erstl;
+
+ /* Enable clock */
+ writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
+
+ /* Disable pull-ups to prevent PHY going into test mode */
+ writel(pin_to_mask(AT91_PIN_PA14) |
+ pin_to_mask(AT91_PIN_PA15) |
+ pin_to_mask(AT91_PIN_PA18),
+ &pioa->pudr);
+
+ /* Power down ethernet */
+ pca953x_set_dir(0x28, IO_EXP_ETH_POWER, PCA953X_DIR_OUT);
+ pca953x_set_val(0x28, IO_EXP_ETH_POWER, 1);
+
+ /* Hold ethernet in reset */
+ pca953x_set_dir(0x28, IO_EXP_ETH_RESET, PCA953X_DIR_OUT);
+ pca953x_set_val(0x28, IO_EXP_ETH_RESET, 0);
+
+ /* Enable ethernet power */
+ pca953x_set_val(0x28, IO_EXP_ETH_POWER, 0);
+
+ /* Need to reset PHY -> 500ms reset */
+ erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
+ writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(13) |
+ AT91_RSTC_MR_URSTEN, &rstc->mr);
+ writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
+
+ /* Wait for end hardware reset */
+ while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL))
+ ;
+
+ /* Restore NRST value */
+ writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN, &rstc->mr);
+
+ /* Bring the ethernet out of reset */
+ pca953x_set_val(0x28, IO_EXP_ETH_RESET, 1);
+
+ /* The phy internal reset take 21ms */
+ udelay(21 * 1000);
+
+ /* Re-enable pull-up */
+ writel(pin_to_mask(AT91_PIN_PA14) |
+ pin_to_mask(AT91_PIN_PA15) |
+ pin_to_mask(AT91_PIN_PA18),
+ &pioa->puer);
+
+ at91_macb_hw_init();
+}
+
+static void nand_hw_init(void)
+{
+ struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+ struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ unsigned long csa;
+
+ /* Enable CS3 as NAND/SmartMedia */
+ csa = readl(&matrix->ebicsa);
+ csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
+ writel(csa, &matrix->ebicsa);
+
+ /* Configure SMC CS3 for NAND/SmartMedia */
+ writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[3].setup);
+ writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(4) |
+ AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(4),
+ &smc->cs[3].pulse);
+ writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
+ &smc->cs[3].cycle);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+ AT91_SMC_MODE_DBW_8 |
+ AT91_SMC_MODE_TDF_CYCLE(3),
+ &smc->cs[3].mode);
+
+ /* Configure RDY/BSY */
+ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
+
+ /* Enable NandFlash */
+ at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
+}
+
+int board_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+ /* Enable PIO clocks */
+ writel((1 << ATMEL_ID_PIOA) |
+ (1 << ATMEL_ID_PIOB) |
+ (1 << ATMEL_ID_PIOC), &pmc->pcer);
+
+ /* The mach-type is the same for both Snapper 9260 and 9G20 */
+ gd->bd->bi_arch_number = MACH_TYPE_SNAPPER_9260;
+
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ /* Initialise peripherals */
+ at91_seriald_hw_init();
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+ nand_hw_init();
+ macb_hw_init();
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ return macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x1f);
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+ return 0;
+}
+
+void reset_phy(void)
+{
+}
diff --git a/boards.cfg b/boards.cfg
index 9b15026..55b5f67 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -81,6 +81,8 @@ at91sam9g20ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel
at91sam9xeek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_NANDFLASH
at91sam9xeek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS0
at91sam9xeek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS1
+snapper9260 arm arm926ejs - bluewater at91 snapper9260:AT91SAM9260
+snapper9g20 arm arm926ejs snapper9260 bluewater at91 snapper9260:AT91SAM9G20
top9000eval_xe arm arm926ejs top9000 emk at91 top9000:EVAL9000
top9000su_xe arm arm926ejs top9000 emk at91 top9000:SU9000
meesc arm arm926ejs - esd at91
diff --git a/include/configs/snapper9260.h b/include/configs/snapper9260.h
new file mode 100644
index 0000000..98fe293
--- /dev/null
+++ b/include/configs/snapper9260.h
@@ -0,0 +1,191 @@
+/*
+ * Bluewater Systems Snapper 9260 and 9G20 modules
+ *
+ * (C) Copyright 2011 Bluewater Systems
+ * Author: Andre Renaud <andre at bluewatersys.com>
+ * Author: Ryan Mallon <ryan at bluewatersys.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* SoC type is defined in boards.cfg */
+#include <asm/hardware.h>
+#include <asm/sizes.h>
+
+#define CONFIG_SYS_TEXT_BASE 0x23f00000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* External Crystal, in Hz */
+#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
+#define CONFIG_SYS_HZ 1000
+
+/* CPU */
+#define CONFIG_ARCH_CPU_INIT
+#undef CONFIG_USE_IRQ
+
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_SKIP_RELOCATE_UBOOT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_FIT
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
+#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* 64MB */
+#define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM1 + 0x1000 - \
+ GENERATED_GBL_DATA_SIZE)
+
+/* Mem test settings */
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + (1024 * 1024))
+
+/* NAND Flash */
+#define CONFIG_NAND_ATMEL
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_DBW_8
+#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */
+#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */
+#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
+#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
+
+/* Ethernet */
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_MULTI
+#define CONFIG_NET_RETRY_COUNT 20
+#define CONFIG_RESET_PHY_R
+#define CONFIG_TFTP_PORT
+#define CONFIG_TFTP_TSIZE
+
+/* USB */
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
+#define CONFIG_USB_STORAGE
+
+/* GPIOs and IO expander */
+#define CONFIG_AT91_LEGACY
+#define CONFIG_ATMEL_LEGACY
+#define CONFIG_AT91_GPIO
+#define CONFIG_AT91_GPIO_PULLUP 1
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_ADDR 0x28
+#define CONFIG_SYS_I2C_PCA953X_WIDTH {{0x28, 16}}
+
+/* UARTs/Serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE ATMEL_BASE_DBGU
+#define CONFIG_USART_ID ATMEL_ID_SYS
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
+#define CONFIG_SYS_PROMPT "Snapper> "
+
+/* I2C - Bit-bashed */
+#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SOFT_I2C_READ_REPEATED_START
+#define CONFIG_I2C_MULTI_BUS
+#define I2C_INIT do { \
+ at91_set_gpio_output(AT91_PIN_PA23, 1); \
+ at91_set_gpio_output(AT91_PIN_PA24, 1); \
+ at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \
+ at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \
+ } while (0)
+#define I2C_SOFT_DECLARATIONS
+#define I2C_ACTIVE
+#define I2C_TRISTATE at91_set_gpio_input(AT91_PIN_PA23, 1);
+#define I2C_READ at91_get_gpio_value(AT91_PIN_PA23);
+#define I2C_SDA(bit) do { \
+ if (bit) { \
+ at91_set_gpio_input(AT91_PIN_PA23, 1); \
+ } else { \
+ at91_set_gpio_output(AT91_PIN_PA23, 1); \
+ at91_set_gpio_value(AT91_PIN_PA23, bit); \
+ } \
+ } while (0)
+#define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit)
+#define I2C_DELAY udelay(2)
+
+/* Boot options */
+#define CONFIG_SYS_LOAD_ADDR 0x23000000
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* Environment settings */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET (512 << 10)
+#define CONFIG_ENV_SIZE (256 << 10)
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_BOOTARGS "console=ttyS0,115200 ip=any"
+
+/* Console settings */
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_EXTBDINFO
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* U-Boot memory settings */
+#define CONFIG_SYS_MALLOC_LEN ( 1 << 20)
+#define CONFIG_STACKSIZE (256 << 10)
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_SOURCE
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+
+#endif /* __CONFIG_H */
--
1.7.0.4
More information about the U-Boot
mailing list