[U-Boot] [PATCH 14/17] update/fix IXDP425 / IXDPG425 boards
Michael Schwingen
michael at schwingen.org
Sat Feb 5 00:06:00 CET 2011
Signed-off-by: Michael Schwingen <michael at schwingen.org>
---
board/ixdp425/config.mk | 2 -
board/ixdp425/flash.c | 427 --------------------------------------------
board/ixdp425/ixdp425.c | 155 ++++++++++++++---
boards.cfg | 2 +-
include/configs/ixdp425.h | 196 ++++++++++++++-------
include/configs/ixdpg425.h | 9 +-
6 files changed, 274 insertions(+), 517 deletions(-)
delete mode 100644 board/ixdp425/config.mk
delete mode 100644 board/ixdp425/flash.c
diff --git a/board/ixdp425/config.mk b/board/ixdp425/config.mk
deleted file mode 100644
index 509c894..0000000
--- a/board/ixdp425/config.mk
+++ /dev/null
@@ -1,2 +0,0 @@
-#
-CONFIG_SYS_TEXT_BASE = 0x00f80000
diff --git a/board/ixdp425/flash.c b/board/ixdp425/flash.c
deleted file mode 100644
index f1d9190..0000000
--- a/board/ixdp425/flash.c
+++ /dev/null
@@ -1,427 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris at nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH ushort
-#define FLASH_PORT_WIDTHV vu_short
-#define SWAP(x) x
-#else
-#define FLASH_PORT_WIDTH ulong
-#define FLASH_PORT_WIDTHV vu_long
-#define SWAP(x) __swab32(x)
-#endif
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- int i;
- ulong size = 0;
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- switch (i) {
- case 0:
- flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
- flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
- break;
- default:
- panic ("configured too many flash banks!\n");
- break;
- }
- size += flash_info[i].size;
- }
-
- /* Protect monitor and environment sectors
- */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_FLASH_BASE,
- CONFIG_SYS_FLASH_BASE + _bss_start - _armboot_start,
- &flash_info[0]);
-
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
- info->protect[i] = 0;
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("INTEL ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F128J3A:
- printf ("28F128J3A\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
- volatile FPW value;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x5555] = (FPW) 0x00AA00AA;
- addr[0x2AAA] = (FPW) 0x00550055;
- addr[0x5555] = (FPW) 0x00900090;
-
- mb ();
- value = addr[0];
-
- switch (value) {
-
- case (FPW) INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
- mb ();
- value = addr[1]; /* device ID */
-
- switch (value) {
-
- case (FPW) INTEL_ID_28F128J3A:
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 0x02000000;
- break; /* => 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- break;
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong type;
- int rcode = 0;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- type = (info->flash_id & FLASH_VENDMASK);
- if ((type != FLASH_MAN_INTEL)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n", prot);
- } else {
- printf ("\n");
- }
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- FPWV *addr = (FPWV *) (info->start[sect]);
- FPW status;
-
- printf ("Erasing sector %2d ... ", sect);
-
- /* arm simple, non interrupt dependent timer */
- reset_timer_masked ();
-
- *addr = (FPW) 0x00500050; /* clear status register */
- *addr = (FPW) 0x00200020; /* erase setup */
- *addr = (FPW) 0x00D000D0; /* erase confirm */
-
- while (((status =
- *addr) & (FPW) 0x00800080) !=
- (FPW) 0x00800080) {
- if (get_timer_masked () >
- CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = (FPW) 0x00B000B0; /* suspend erase */
- *addr = (FPW) 0x00FF00FF; /* reset to read mode */
- rcode = 1;
- break;
- }
- }
-
- *addr = (FPW) 0x00500050; /* clear status register cmd. */
- *addr = (FPW) 0x00FF00FF; /* resest to read mode */
-
- printf (" done\n");
- }
- }
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- FPW data;
- int count, i, l, rc, port_width;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
- wp = (addr & ~1);
- port_width = 2;
-#else
- wp = (addr & ~3);
- port_width = 4;
-#endif
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < port_width && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, SWAP (data))) != 0) {
- return (rc);
- }
- wp += port_width;
- }
-
- /*
- * handle word aligned part
- */
- count = 0;
- while (cnt >= port_width) {
- data = 0;
- for (i = 0; i < port_width; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data (info, wp, SWAP (data))) != 0) {
- return (rc);
- }
- wp += port_width;
- cnt -= port_width;
- if (count++ > 0x800) {
- spin_wheel ();
- count = 0;
- }
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_data (info, wp, SWAP (data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
- FPWV *addr = (FPWV *) dest;
- ulong status;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- printf ("not erased at %08lx (%lx)\n", (ulong) addr,
- (ulong) * addr);
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- *addr = (FPW) 0x00400040; /* write setup */
- *addr = data;
-
- /* arm simple, non interrupt dependent timer */
- reset_timer_masked ();
-
- /* wait while polling the status register */
- while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if (get_timer_masked () > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
- return (1);
- }
- }
-
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (0);
-}
-
-void inline spin_wheel (void)
-{
- static int p = 0;
- static char w[] = "\\/-";
-
- printf ("\010%c", w[p]);
- (++p == 3) ? (p = 0) : 0;
-}
diff --git a/board/ixdp425/ixdp425.c b/board/ixdp425/ixdp425.c
index 43ac8f6..e2cbcd0 100644
--- a/board/ixdp425/ixdp425.c
+++ b/board/ixdp425/ixdp425.c
@@ -33,24 +33,82 @@
#include <malloc.h>
#include <netdev.h>
#include <asm/arch/ixp425.h>
+#include <asm/io.h>
+#ifdef CONFIG_PCI
+#include <pci.h>
+#include <asm/arch/ixp425pci.h>
+#endif
DECLARE_GLOBAL_DATA_PTR;
+#define IXDP425_LED_PORT 0x52000000 /* 4-digit hex display */
+
+int board_early_init_f(void)
+{
+ /* CS2: LED port */
+ writel(0xbcff0002, IXP425_EXP_CS2);
+ writew(0x0001, IXDP425_LED_PORT); /* output postcode to LEDs */
+
+ return 0;
+}
+
+#ifdef CONFIG_PCI
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_ixpdp425_config_table[] = {
+ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, PCI_ANY_ID,
+ pci_cfgfunc_config_device,
+ { 0x400,
+ 0x40000000,
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER } },
+
+ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x01, PCI_ANY_ID,
+ pci_cfgfunc_config_device,
+ { 0x800,
+ 0x40010000,
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER } },
+
+ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x02, PCI_ANY_ID,
+ pci_cfgfunc_config_device,
+ { 0xc00,
+ 0x40020000,
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER } },
+
+ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x03, PCI_ANY_ID,
+ pci_cfgfunc_config_device,
+ { 0x1000,
+ 0x40030000,
+ PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER } },
+ { }
+};
+#endif
+
+struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+ config_table: pci_ixpdp425_config_table,
+#endif
+};
+#endif /* CONFIG_PCI */
+
+
/*
* Miscelaneous platform dependent initialisations
*/
-int board_init (void)
+int board_init(void)
{
+ writew(0x0002, IXDP425_LED_PORT); /* output postcode to LEDs */
+
+#ifdef CONFIG_IXDPG425
+ /* arch number of IXDP */
+ gd->bd->bi_arch_number = MACH_TYPE_IXDPG425;
+#else
/* arch number of IXDP */
gd->bd->bi_arch_number = MACH_TYPE_IXDP425;
+#endif
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x00000100;
#ifdef CONFIG_IXDPG425
- /* arch number of IXDP */
- gd->bd->bi_arch_number = MACH_TYPE_IXDPG425;
-
/*
* Get realtek RTL8305 switch and SLIC out of reset
*/
@@ -60,19 +118,56 @@ int board_init (void)
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_SLIC_RESET_N);
/*
- * Setup GPIO's for PCI INTA & INTB
+ * Setup GPIOs for PCI INTA & INTB
*/
GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA_N);
GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA_N);
GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB_N);
GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB_N);
- /*
- * Setup GPIO's for 33MHz clock output
- */
- *IXP425_GPIO_GPCLKR = 0x01FF01FF;
+ /* Setup GPIOs for 33MHz clock output */
+ writel(0x01FF01FF, IXP425_GPIO_GPCLKR);
+
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
+
+ /* set GPIO8..11 interrupt type to active low */
+ writel((0x1 << 9) | (0x1 << 6) | (0x1 << 3) | 0x1, IXP425_GPIO_GPIT2R);
+
+ /* clear pending interrupts */
+ writel(-1, IXP425_GPIO_GPISR);
+
+ /* assert PCI reset */
+ GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_SLIC_RESET_N);
+
+ udelay(533);
+
+ /* deassert PCI reset */
+ GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_SLIC_RESET_N);
+
+ udelay(533);
+
+#else /* IXDP425 */
+ /* Setup GPIOs for 33MHz ExpBus and PCI clock output */
+ writel(0x01FF01FF, IXP425_GPIO_GPCLKR);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
+ GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_RESET_N);
+
+ /* set GPIO8..11 interrupt type to active low */
+ writel((0x1 << 9) | (0x1 << 6) | (0x1 << 3) | 0x1, IXP425_GPIO_GPIT2R);
+ /* clear pending interrupts */
+ writel(-1, IXP425_GPIO_GPISR);
+
+ /* assert PCI reset */
+ GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PCI_RESET_N);
+
+ udelay(533);
+
+ /* deassert PCI reset */
+ GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_PCI_RESET_N);
+
+ udelay(533);
#endif
return 0;
@@ -97,30 +192,46 @@ int checkboard(void)
}
putc('\n');
- return (0);
+ return 0;
}
-int dram_init (void)
+int dram_init(void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- return (0);
+ /* we can only map 64MB via PCI, so we limit memory
+ until a better solution is implemented. */
+#ifdef CONFIG_PCI
+ gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 64<<20);
+#else
+ gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 256<<20);
+#endif
+ return 0;
}
-#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
-extern struct pci_controller hose;
-extern void pci_ixp_init(struct pci_controller * hose);
-
+#ifdef CONFIG_PCI
void pci_init_board(void)
{
- extern void pci_ixp_init (struct pci_controller *hose);
-
pci_ixp_init(&hose);
}
+
+/*
+ * dev 0 on the PCI bus is not the host bridge, so we have to override
+ * these functions in order to not skip PCI slot 0 during configuration.
+*/
+int pci_skip_dev(struct pci_controller *hose, pci_dev_t dev)
+{
+ return 0;
+}
+int pci_print_dev(struct pci_controller *hose, pci_dev_t dev)
+{
+ return 1;
+}
+
#endif
int board_eth_init(bd_t *bis)
{
- return pci_eth_init(bis);
+#ifdef CONFIG_PCI
+ pci_eth_init(bis);
+#endif
+ return cpu_eth_init(bis);
}
diff --git a/boards.cfg b/boards.cfg
index 5ec40b1..1a93358 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -136,7 +136,7 @@ actux3 arm ixp
actux4 arm ixp
dvlhost arm ixp
ixdp425 arm ixp
-ixdpg425 arm ixp
+ixdpg425 arm ixp ixdp425
lpd7a400 arm lh7a40x lpd7a40x
lpd7a404 arm lh7a40x lpd7a40x
balloon3 arm pxa
diff --git a/include/configs/ixdp425.h b/include/configs/ixdp425.h
index 28d41e2..4bad31d 100644
--- a/include/configs/ixdp425.h
+++ b/include/configs/ixdp425.h
@@ -36,12 +36,19 @@
#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info (and speed) */
#define CONFIG_DISPLAY_BOARDINFO 1 /* display board info */
+/*
+ * select serial console configuration
+ */
+#define CONFIG_IXP_SERIAL
+#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
/***************************************************************
* U-boot generic defines start here.
***************************************************************/
-#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
-
/*
* Size of malloc() pool
*/
@@ -50,9 +57,6 @@
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_BAUDRATE 115200
-
-
/*
* BOOTP options
*/
@@ -61,38 +65,33 @@
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
+/* Command line configuration. */
#include <config_cmd_default.h>
#define CONFIG_CMD_ELF
-#define CONFIG_CMD_PCI
-
#define CONFIG_PCI
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_PCI_PNP
#define CONFIG_IXP_PCI
-#define CONFIG_NET_MULTI
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI_ENUM
#define CONFIG_EEPRO100
+#endif
-#define CONFIG_BOOTDELAY 3
-/*#define CONFIG_ETHADDR 08:00:3e:26:0a:5b*/
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 192.168.0.21
-#define CONFIG_SERVERIP 192.168.0.148
-#define CONFIG_BOOTCOMMAND "bootm 50040000"
-#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
-#define CONFIG_CMDLINE_TAG
+#define CONFIG_BOOTCOMMAND "run boot_flash"
+/* enable passing of ATAGs */
+#define CONFIG_CMDLINE_TAG 1
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_INITRD_TAG 1
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/*
- * Miscellaneous configurable options
- */
+/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
@@ -103,10 +102,13 @@
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
-#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK 66666666
+#define CONFIG_SYS_HZ 1000
+
+/* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x00010000
-#define CONFIG_SYS_HZ 3333333 /* spec says 66.666 MHz, but it appears to be 33 */
- /* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
@@ -115,10 +117,6 @@
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
-#endif
/***************************************************************
* Platform/Board specific defines start here.
@@ -129,71 +127,145 @@
*/
-/*
- * select serial console configuration
- */
-#define CONFIG_IXP_SERIAL
-#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */
/*
* Physical Memory Map
*/
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 2 banks of DRAM */
-#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */
+#define CONFIG_SYS_TEXT_BASE 0x50000000
#define PHYS_FLASH_1 0x50000000 /* Flash Bank #1 */
#define PHYS_FLASH_SIZE 0x00800000 /* 8 MB */
#define PHYS_FLASH_BANK_SIZE 0x00800000 /* 8 MB Banks */
#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors (x1) */
-#define CONFIG_SYS_DRAM_BASE 0x00000000
-#define CONFIG_SYS_DRAM_SIZE 0x01000000
-
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_BOARD_SIZE_LIMIT 262144
-/*
- * Expansion bus settings
- */
-#define CONFIG_SYS_EXP_CS0 0xbcd23c42
+/* Expansion bus settings */
+#define CONFIG_SYS_EXP_CS0 0xbcd23c42
+
+/* SDRAM settings */
+#define CONFIG_NR_DRAM_BANKS 1 /* we have 2 banks of DRAM */
+#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
-/*
- * SDRAM settings
- */
#define CONFIG_SYS_SDR_CONFIG 0xd
#define CONFIG_SYS_SDR_MODE_CONFIG 0x1
#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
/*
- * GPIO settings
- */
-
-/*
- * FLASH and environment organization
- */
-/*
* FLASH and environment organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 }
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */
-
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x20000)
+#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x40000)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+/* Use common CFI driver */
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+/* no byte writes on IXP4xx */
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+/* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+
+/* Ethernet */
+
+/* include IXP4xx NPE support */
+#define CONFIG_IXP4XX_NPE 1
+#define CONFIG_NET_MULTI 1
+/* NPE0 PHY address */
+#define CONFIG_PHY_ADDR 0
+/* NPE1 PHY address (HW Release E only) */
+#define CONFIG_PHY1_ADDR 1
+/* MII PHY management */
+#define CONFIG_MII 1
+/* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SYS_RX_ETH_BUFFER 16
+
+#define CONFIG_HAS_ETH1 1
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#undef CONFIG_CMD_NFS
+
+/* Cache Configuration */
+#define CONFIG_SYS_CACHELINE_SIZE 32
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "npe_ucode=50060000\0" \
+ "mtd=IXP4XX-Flash.0:256k(uboot),128k(env),128k(ucode),2048k(linux),-(root)\0" \
+ "kerneladdr=50080000\0" \
+ "kernelfile=ixdp425/uImage\0" \
+ "rootfile=ixdp425/rootfs\0" \
+ "rootaddr=50280000\0" \
+ "loadaddr=10000\0" \
+ "updateboot_ser=mw.b 10000 ff 40000;" \
+ " loady ${loadaddr};" \
+ " run eraseboot writeboot\0" \
+ "updateboot_net=mw.b 10000 ff 40000;" \
+ " tftp ${loadaddr} ixdp425/u-boot.bin;" \
+ " run eraseboot writeboot\0" \
+ "eraseboot=protect off 50000000 5003ffff;" \
+ " erase 50000000 5003ffff\0" \
+ "writeboot=cp.b 10000 50000000 ${filesize}\0" \
+ "updateucode=loady;" \
+ " era ${npe_ucode} +${filesize};" \
+ " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \
+ "updateroot=tftp ${loadaddr} ${rootfile};" \
+ " era ${rootaddr} +${filesize};" \
+ " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \
+ "updatekern=tftp ${loadaddr} ${kernelfile};" \
+ " era ${kerneladdr} +${filesize};" \
+ " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \
+ "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4" \
+ " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \
+ "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4" \
+ " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
+ "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \
+ "boot_flash=run flashargs addtty addeth;" \
+ " bootm ${kerneladdr}\0" \
+ "boot_net=run netargs addtty addeth;" \
+ " tftpboot ${loadaddr} ${kernelfile};" \
+ " bootm\0"
+
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GPIO_UTOPIA_GPIO1 0
+#define CONFIG_SYS_GPIO_UTOPIA_IRQ_N 1
+#define CONFIG_SYS_GPIO_HSS1_IRQ_N 2
+#define CONFIG_SYS_GPIO_HSS0_IRQ_N 3
+#define CONFIG_SYS_GPIO_ETH0_IRQ_N 4
+#define CONFIG_SYS_GPIO_ETH1_IRQ_N 5
+#define CONFIG_SYS_GPIO_I2C_SCL 6
+#define CONFIG_SYS_GPIO_I2C_SDA 7
+#define CONFIG_SYS_GPIO_PCI_INTD_N 8
+#define CONFIG_SYS_GPIO_PCI_INTC_N 9
+#define CONFIG_SYS_GPIO_PCI_INTB_N 10
+#define CONFIG_SYS_GPIO_PCI_INTA_N 11
+#define CONFIG_SYS_GPIO_UTOPIA_GPIO0 12
+#define CONFIG_SYS_GPIO_PCI_RESET_N 13
+#define CONFIG_SYS_GPIO_PCI_CLK 14
+#define CONFIG_SYS_GPIO_EXTBUS_CLK 15
+
#endif /* __CONFIG_H */
diff --git a/include/configs/ixdpg425.h b/include/configs/ixdpg425.h
index 637fd7d..60a2371 100644
--- a/include/configs/ixdpg425.h
+++ b/include/configs/ixdpg425.h
@@ -53,9 +53,6 @@
/*
* Misc configuration options
*/
-#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
-#define CONFIG_USE_IRQ 1 /* we need IRQ stuff for timer */
-#define CONFIG_TIMER_IRQ
#define CONFIG_BOOTCOUNT_LIMIT /* support for bootcount limit */
#define CONFIG_SYS_BOOTCOUNT_ADDR 0x60003000 /* inside qmrg sram */
@@ -115,6 +112,7 @@
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
+#define CONFIG_IXP425_TIMER_CLK 66666666
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/* valid baudrates */
@@ -248,4 +246,9 @@
*/
#define CONFIG_SYS_CACHELINE_SIZE 32
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_SDRAM_BASE 0
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */
--
1.7.2.3
More information about the U-Boot
mailing list