[U-Boot] [RFC] ARM: mx31pdk: Use the new relocation scheme

[Albert ARIBAUD]

Le 06/02/2011 13:03, Magnus Lilja a écrit :
> Hi all
>
> On 01/14/2011 07:33 PM, Fabio Estevam wrote:
>> Hi Stefano,
>>
>> On 1/13/2011 11:38 AM, Stefano Babic wrote:
>>> On 01/12/2011 01:49 PM, Fabio Estevam wrote:
>>>> Hi,
>>>
>>> Hi Fabio,
>>>
>>>>
>>>> I am trying to make the new relocation scheme to work on the mx31pdk board.
>>>>
>>>> With this patch applied the mx31pdk build works, but not able to get a U-boot prompt yet.
>>>
>>> I have tried to imagine some issues, but I cannot find a clear reason.
>>> Building with your patch I checked that nand_spl is still less than 2KB
>>> code, and that matches the NAND page, as required by i.MX31 - so it is
>>> not a problem.
>>>
>>> Have you tried to disable the relocation, just to check if the
>>> relocation is an issue with CONFIG_SKIP_RELOCATE_UBOOT ? This is not a
>>> solution, but only to check what happens.
>
> I've done some testing now and ended up comparing start.S for ARM1136 with ARM926EJS since
> the latter is used on the Karo TX25 board which seems to have been updated and
> also boots from NAND.
>
> The result is that applying the following patch on top of Fabios patch makes the i.MX31 PDK
> boot from NAND. Booting Linux from TFTP works nicely. However the first few lines of output
> from U-boot is missing, only the "NAND: 256 MB" line is shown. I haven't tried to understand
> how booting works nowadays and why these changes work, perhaps someone with more insight
> in the mechanisms can figure out the correct assembler code.
>
> I have no idea if this breaks other boards but at least it's start for further work. I tried
> it on the imx31 litekit (which boots from NOR) but that board doesn't seem to boot even before applying Fabios patch,
> I'll see if I can figure out why that board is broken now. Don't know when though.
>
> Regards, Magnus Lilja
>
> diff --git a/arch/arm/cpu/arm1136/start.S b/arch/arm/cpu/arm1136/start.S
> index 12545c2..7d75ecf 100644
> --- a/arch/arm/cpu/arm1136/start.S
> +++ b/arch/arm/cpu/arm1136/start.S
> @@ -163,6 +163,9 @@ call_board_init_f:
>          bic     sp, sp, #7 /* 8-byte alignment for ABI compliance */
>          ldr     r0,=0x00000000
>
> +#if 1
> +       bl      board_init_f
> +#else
>   #ifdef CONFIG_NAND_SPL
>          bl      nand_boot
>   #else
> @@ -172,6 +175,7 @@ call_board_init_f:
>          bl      board_init_f
>   #endif /* CONFIG_ONENAND_IPL */
>   #endif /* CONFIG_NAND_SPL */
> +#endif
>
>   /*------------------------------------------------------------------------------*/
>
> @@ -266,11 +270,19 @@ clbss_l:str       r2, [r0]                /* clear loop...                    */
>    * initialization, now running from RAM.
>    */
>   #ifdef CONFIG_NAND_SPL
> +#if 1
> +       ldr     r0, _nand_boot_ofs
> +       mov     pc, r0
> +
> +_nand_boot_ofs:
> +       .word nand_boot
> +#else
>          ldr     r0, _nand_boot_ofs
>          adr     r1, _start
>          add     pc, r0, r1
>   _nand_boot_ofs:
>          .word nand_boot - _start
> +#endif
>   #else
>   jump_2_ram:
>          ldr     r0, _board_init_r_ofs
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot

Can you repost the diff without those pesky '#if 1...#else...#endif' 
additions? Just take the current master code, do the changes needed to 
make it work without trying to keep the old lines around, then do the 
diff. I'll be easier for all to see the changes.

Amicalement,
-- 
Albert.