[U-Boot] IMX51 EVK Splash Screen

Thomas Besemer thomas.besemer at gmail.com
Thu Jan 20 03:06:56 CET 2011


Hi folks -

I had posted last week.  I was able to get basic Splash Screen going on EVK,
through using patches I found from googling around.  At the end of this email,
the patch set that shows the differences from the U-Boot I pulled on
12/24/2010.  I am not sure I have the right patch set, but in this case,
what I have does seem to work; U-Boot does output to LCD display on the
second Display Interface.

Through some of the archives, this one specifically:

http://www.mail-archive.com/u-boot@lists.denx.de/msg41664.html

There seems to have been a discussion on lcd_setmem().  Has this been
resolved, and I missed it?  You'll see from patch set that I just put a
very large buffer in place (hard coded hack).  U-Boot hung on boot before
I put this in, and based on what I see on mailing list, this seems to be
an issue of not having the display information available early on in boot.

At any rate, I got it to boot, and see that the LCD shows display on
startup.  Yet, I lose the console on this; the serial port is read, but
the output goes to LCD.

I have still not displayed a bit map image, but with IPU working, not
horribly concerned.

In an ideal world, what I would like is to not loose the console.  I want
stdin/stdout to remain on serial port, while I toss a bit map out on LCD.
Any comments on how to do this?  End game is that I toss a splash screen
up on LCD on EVK, while having U-Boot information still on the console.

So, a couple of things:

1. Do I have correct patch work for this version of U-Boot, or is there a
newer version of U-Boot to pull?  I pulled both mainline and IMX tree
yesterday, don't see the MX51 EVK in them.

2. How to configure so that I get console while LCD is available for display.

3. What is current status on lcd_setmem() thing.

If this patch set that I have is workable, then I am going to move forward
to put in support for DVI interface on EVK, and figure out how to use
U-Boot Environment Variables to specify which DIU to use.

I might have missed a few things along the way folks; I am not the sharpest
tool in the shed.  Please let me know if I missed patch sets on lcd_setmem(),
and help me understand how to make sure console works with Splash Screen.

Thanks,

tom


Index: include/configs/mx51evk.h
===================================================================
--- include/configs/mx51evk.h	(revision 173)
+++ include/configs/mx51evk.h	(working copy)
@@ -190,6 +190,15 @@
 #define CONFIG_SYS_DDR_CLKSEL	0
 #define CONFIG_SYS_CLKTL_CBCDR	0x59E35100

+/*
+ * Framebuffer and LCD
+ */
+#define CONFIG_LCD
+#define CONFIG_VIDEO_MX5
+#define LCD_BPP		LCD_COLOR16
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+
 /*-----------------------------------------------------------------------
  * FLASH and environment organization
  */
Index: board/freescale/mx51evk/mx51evk.c
===================================================================
--- board/freescale/mx51evk/mx51evk.c	(revision 170)
+++ board/freescale/mx51evk/mx51evk.c	(working copy)
@@ -34,10 +34,38 @@
 #include <fsl_pmic.h>
 #include <mc13892.h>

+#ifdef CONFIG_LCD
+#include <linux/fb.h>
+#include <lcd.h>
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;

 static u32 system_rev;
+extern int mx51_fb_init(struct fb_videomode *mode, u32 ipu_di, u32 pix_fmt);

+#ifdef CONFIG_LCD
+static struct fb_videomode claa_wvga = {
+	"CLAA07LC0ACW",
+	57,	/* Refresh */
+	800,	/* xres */
+	480,	/* yres */
+	37037,	/* pixclock = 27Mhz */
+	40,	/* left margin */
+	60,	/* right margin */
+	10,	/* upper margin */
+	10,	/* lower margin */
+	20,	/* hsync-len */
+	10,	/* vsync-len */
+	0,	/* sync */
+	FB_VMODE_NONINTERLACED,	/* vmode */
+	0,	/* flag */
+};
+
+static int wvga_ipu_di = 1;
+static int wvga_bppix = 16;
+#endif
+
 #ifdef CONFIG_FSL_ESDHC
 struct fsl_esdhc_cfg esdhc_cfg[2] = {
 	{MMC_SDHC1_BASE_ADDR, 1},
@@ -148,6 +176,41 @@
 	mxc_iomux_set_pad(MX51_PIN_NANDF_D11, 0x2180);
 }

+#ifdef CONFIG_LCD
+void setup_iomux_ipu(void)
+{
+	puts( "setup_iopmux_ipu(): invoked\n" );
+	/* DISP2_DAT [0:15] are configured by default */
+	mxc_request_iomux(MX51_PIN_DI1_D1_CS, IOMUX_CONFIG_ALT4);
+	mxc_iomux_set_pad(MX51_PIN_DI1_D1_CS,
+		PAD_CTL_PKE_ENABLE | PAD_CTL_DRV_HIGH | PAD_CTL_SRE_FAST);
+	mxc_request_iomux(MUX_IN_GPIO3_IPP_IND_G_IN_4_SELECT_INPUT,
+		INPUT_CTL_PATH1);
+
+	/* DISP2_DRDY pin */
+	mxc_request_iomux(MX51_PIN_DI_GP4, IOMUX_CONFIG_ALT4);
+	mxc_iomux_set_pad(MX51_PIN_DI_GP4, PAD_CTL_PKE_ENABLE |
+		PAD_CTL_PUE_KEEPER | PAD_CTL_DRV_LOW);
+
+	puts( "setup_iopmux_ipu(): done\n" );
+}
+
+#endif
+
+#ifdef CONFIG_LCD
+void lcd_enable(void)
+{
+	int ret;
+puts( "lcd_enable(): invoked\n" );
+
+	ret = mx51_fb_init(&claa_wvga, wvga_ipu_di, wvga_bppix);
+	if (ret) {
+		puts("LCD cannot be configured\n");
+	}
+
+}
+#endif
+
 #ifdef CONFIG_MXC_SPI
 static void setup_iomux_spi(void)
 {
@@ -409,7 +472,9 @@

 	setup_iomux_uart();
 	setup_iomux_fec();
-
+#ifdef CONFIG_LCD
+	setup_iomux_ipu();
+#endif
 	return 0;
 }

Index: common/lcd.c
===================================================================
--- common/lcd.c	(revision 170)
+++ common/lcd.c	(working copy)
@@ -438,16 +438,21 @@
 ulong lcd_setmem (ulong addr)
 {
 	ulong size;
+#ifdef	ORIGINAL_PRE_TBESEMER
 	int line_length = (panel_info.vl_col * NBITS (panel_info.vl_bpix)) / 8;

 	debug ("LCD panel info: %d x %d, %d bit/pix\n",
 		panel_info.vl_col, panel_info.vl_row, NBITS (panel_info.vl_bpix) );

 	size = line_length * panel_info.vl_row;
+#else
+	size = 1024 * 1024 * 12;

 	/* Round up to nearest full page */
 	size = (size + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);

+#endif
+
 	/* Allocate pages for the frame buffer. */
 	addr -= size;


Index: drivers/video/mxc_ipuv3_fb.c
===================================================================
--- drivers/video/mxc_ipuv3_fb.c	(revision 170)
+++ drivers/video/mxc_ipuv3_fb.c	(working copy)
@@ -526,7 +526,7 @@
  *
  * @return      Appropriate error code to the kernel common code
  */
-static int mxcfb_probe(u32 interface_pix_fmt, struct fb_videomode *mode)
+static int mxcfb_probe(u32 interface_pix_fmt, struct fb_videomode
*mode, u32 ipu_di)
 {
 	struct fb_info *fbi;
 	struct mxcfb_info *mxcfbi;
@@ -550,11 +550,14 @@
 		mxcfbi->blank = FB_BLANK_POWERDOWN;
 	}

-	mxcfbi->ipu_di = 0;
+	mxcfbi->ipu_di = ipu_di;

 	ipu_disp_set_global_alpha(mxcfbi->ipu_ch, 1, 0x80);
 	ipu_disp_set_color_key(mxcfbi->ipu_ch, 0, 0);
-	strcpy(fbi->fix.id, "DISP3 BG");
+        if (ipu_di == 0)
+                strcpy(fbi->fix.id, "DISP3 BG");
+        else if (ipu_di == 1)
+                strcpy(fbi->fix.id, "DISP3 BG - DI1");

 	g_dp_in_use = 1;

@@ -625,9 +628,10 @@
 	memset(lcdbase, 0, mem_len);
 }

-int mx51_fb_init(struct fb_videomode *mode)
+int mx51_fb_init(struct fb_videomode *mode, u32 ipu_di, u32 bppix)
 {
 	int ret;
+	uint32_t pixfmt = 0;

 	ret = ipu_probe();
 	if (ret)
@@ -635,8 +639,24 @@

 	lcd_base += 56;

+        switch (bppix) {
+        case 32:
+                pixfmt = IPU_PIX_FMT_BGR32;
+                break;
+        case 24:
+                pixfmt = IPU_PIX_FMT_BGR24;
+                break;
+        case 18:
+                pixfmt = IPU_PIX_FMT_RGB666;
+                break;
+        case 16:
+                pixfmt = IPU_PIX_FMT_RGB565;
+                break;
+        }
+
+
 	debug("Framebuffer at 0x%x\n", (unsigned int)lcd_base);
-	ret = mxcfb_probe(IPU_PIX_FMT_RGB666, mode);
+	ret = mxcfb_probe(pixfmt, mode, ipu_di);

 	return ret;
 }


More information about the U-Boot mailing list