[U-Boot] [PATCH v1] powerpc/85xx: Add support for Integrated Flash Controller (IFC)

Dipen Dudhat Dipen.Dudhat at freescale.com
Thu Jan 20 11:59:35 CET 2011


The Integrated Flash Controller (IFC) is used to access the external
NAND Flash, NOR Flash, EPROM, SRAM and Generic ASIC memories.Four chip
selects are provided in IFC so that maximum of four Flash devices can be
hooked, but only one can be accessed at a given time.

Features supported by IFC are,
        - Functional muxing of pins between NAND, NOR and GPCM
        - Support memory banks of size 64KByte to 4 GBytes
        - Write protection capability (only for NAND and NOR)
        - Provision of Software Reset
        - Flexible Timing programmability for every chip select
        - NAND Machine
                - x8/ x16 NAND Flash Interface
                - SLC and MLC NAND Flash devices support with
                  configurable
                  page sizes of upto 4KB
                - Internal SRAM of 9KB which is directly mapped and
                  availble at
                  boot time for NAND Boot
                - Configurable block size
                - Boot chip select (CS0) available at system reset
        - NOR Machine
                - Data bus width of 8/16/32
                - Compatible with asynchronous NOR Flash
                - Directly memory mapped
                - Supports address data multiplexed (ADM) NOR device
                - Boot chip select (CS0) available at system reset
        - GPCM Machine (NORMAL GPCM Mode)
                - Support for x8/16/32 bit device
                - Compatible with general purpose addressable device
                  e.g. SRAM, ROM
                - External clock is supported with programmable division
                  ratio
        - GPCM Machine (Generic ASIC Mode)
                - Support for x8/16/32 bit device
                - Address and Data are shared on I/O bus
                - Following Address and Data sequences can be supported
                  on I/O bus
                       - 32 bit I/O: AD
                       - 16 bit I/O: AADD
                       - 8 bit I/O : AAAADDDD
                - Configurable Even/Odd Parity on Address/Data bus
                  supported

Signed-off-by: Dipen Dudhat <Dipen.Dudhat at freescale.com>
Acked-by: Scott Wood <scottwood at freescale.com>
---
Changes from v0:
	- Integrated Wolfgang's comments
 arch/powerpc/cpu/mpc85xx/cpu.c        |    7 +-
 arch/powerpc/cpu/mpc8xxx/Makefile     |    1 +
 arch/powerpc/cpu/mpc8xxx/fsl_ifc.c    |   84 +++
 arch/powerpc/include/asm/config.h     |    2 +
 arch/powerpc/include/asm/fsl_ifc.h    |  947 +++++++++++++++++++++++++++++++++
 arch/powerpc/include/asm/fsl_law.h    |    1 +
 arch/powerpc/include/asm/immap_85xx.h |    4 +
 7 files changed, 1045 insertions(+), 1 deletions(-)
 create mode 100644 arch/powerpc/cpu/mpc8xxx/fsl_ifc.c
 create mode 100644 arch/powerpc/include/asm/fsl_ifc.h

diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c
index 1aad2ba..49ea6cc 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu.c
@@ -33,6 +33,7 @@
 #include <asm/cache.h>
 #include <asm/io.h>
 #include <asm/mmu.h>
+#include <asm/fsl_ifc.h>
 #include <asm/fsl_law.h>
 #include <asm/fsl_lbc.h>
 #include <post.h>
@@ -280,7 +281,8 @@ int cpu_mmc_init(bd_t *bis)
 
 /*
  * Print out the state of various machine registers.
- * Currently prints out LAWs, BR0/OR0, and TLBs
+ * Currently prints out LAWs, BR0/OR0 for LBC, CSPR/CSOR/Timing
+ * parameters for IFC and TLBs
  */
 void mpc85xx_reginfo(void)
 {
@@ -289,6 +291,9 @@ void mpc85xx_reginfo(void)
 #if defined(CONFIG_FSL_LBC)
 	print_lbc_regs();
 #endif
+#ifdef CONFIG_FSL_IFC
+	print_ifc_regs();
+#endif
 
 }
 
diff --git a/arch/powerpc/cpu/mpc8xxx/Makefile b/arch/powerpc/cpu/mpc8xxx/Makefile
index 5dfd65b..4ae26e4 100644
--- a/arch/powerpc/cpu/mpc8xxx/Makefile
+++ b/arch/powerpc/cpu/mpc8xxx/Makefile
@@ -15,6 +15,7 @@ COBJS-y	+= cpu.o
 endif
 
 COBJS-$(CONFIG_OF_LIBFDT) += fdt.o
+COBJS-$(CONFIG_FSL_IFC) += fsl_ifc.o
 COBJS-$(CONFIG_FSL_LBC) += fsl_lbc.o
 COBJS-$(CONFIG_SYS_SRIO) += srio.o
 
diff --git a/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c b/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c
new file mode 100644
index 0000000..39a4556
--- /dev/null
+++ b/arch/powerpc/cpu/mpc8xxx/fsl_ifc.c
@@ -0,0 +1,84 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Author: Dipen Dudhat <dipen.dudhat at freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_ifc.h>
+
+void print_ifc_regs(void)
+{
+	int i, j;
+
+	printf("IFC Controller Registers\n");
+	for (i = 0; i < FSL_IFC_BANK_COUNT; i++) {
+		printf("CSPR%d:0x%08X\tAMASK%d:0x%08X\tCSOR%d:0x%08X\n",
+			i, get_ifc_cspr(i), i, get_ifc_amask(i),
+			i, get_ifc_csor(i));
+		for (j = 0; j < 4; j++)
+			printf("IFC_FTIM%d:0x%08X\n", j, get_ifc_ftim(i, j));
+	}
+}
+
+void init_early_memctl_regs(void)
+{
+#if defined(CONFIG_SYS_CSPR0) && defined(CONFIG_SYS_CSOR0)
+	set_ifc_cspr(IFC_CS0, CONFIG_SYS_CSPR0);
+	set_ifc_amask(IFC_CS0, CONFIG_SYS_AMASK0);
+	set_ifc_csor(IFC_CS0, CONFIG_SYS_CSOR0);
+
+	set_ifc_ftim(IFC_CS0, IFC_FTIM0, CONFIG_SYS_CS0_FTIM0);
+	set_ifc_ftim(IFC_CS0, IFC_FTIM1, CONFIG_SYS_CS0_FTIM1);
+	set_ifc_ftim(IFC_CS0, IFC_FTIM2, CONFIG_SYS_CS0_FTIM2);
+	set_ifc_ftim(IFC_CS0, IFC_FTIM3, CONFIG_SYS_CS0_FTIM3);
+#endif
+
+#if defined(CONFIG_SYS_CSPR1) && defined(CONFIG_SYS_CSOR1)
+	set_ifc_csor(IFC_CS1, CONFIG_SYS_CSOR1);
+	set_ifc_amask(IFC_CS1, CONFIG_SYS_AMASK1);
+	set_ifc_cspr(IFC_CS1, CONFIG_SYS_CSPR1);
+
+	set_ifc_ftim(IFC_CS1, IFC_FTIM0, CONFIG_SYS_CS1_FTIM0);
+	set_ifc_ftim(IFC_CS1, IFC_FTIM1, CONFIG_SYS_CS1_FTIM1);
+	set_ifc_ftim(IFC_CS1, IFC_FTIM2, CONFIG_SYS_CS1_FTIM2);
+	set_ifc_ftim(IFC_CS1, IFC_FTIM3, CONFIG_SYS_CS1_FTIM3);
+#endif
+
+#if defined(CONFIG_SYS_CSPR2) && defined(CONFIG_SYS_CSOR2)
+	set_ifc_csor(IFC_CS2, CONFIG_SYS_CSOR2);
+	set_ifc_amask(IFC_CS2, CONFIG_SYS_AMASK2);
+	set_ifc_cspr(IFC_CS2, CONFIG_SYS_CSPR2);
+
+	set_ifc_ftim(IFC_CS2, IFC_FTIM0, CONFIG_SYS_CS2_FTIM0);
+	set_ifc_ftim(IFC_CS2, IFC_FTIM1, CONFIG_SYS_CS2_FTIM1);
+	set_ifc_ftim(IFC_CS2, IFC_FTIM2, CONFIG_SYS_CS2_FTIM2);
+	set_ifc_ftim(IFC_CS2, IFC_FTIM3, CONFIG_SYS_CS2_FTIM3);
+
+#endif
+
+#if defined(CONFIG_SYS_CSPR3) && defined(CONFIG_SYS_CSOR3)
+	set_ifc_cspr(IFC_CS3, CONFIG_SYS_CSPR3);
+	set_ifc_amask(IFC_CS3, CONFIG_SYS_AMASK3);
+	set_ifc_csor(IFC_CS3, CONFIG_SYS_CSOR3);
+
+	set_ifc_ftim(IFC_CS3, IFC_FTIM0, CONFIG_SYS_CS3_FTIM0);
+	set_ifc_ftim(IFC_CS3, IFC_FTIM1, CONFIG_SYS_CS3_FTIM1);
+	set_ifc_ftim(IFC_CS3, IFC_FTIM2, CONFIG_SYS_CS3_FTIM2);
+	set_ifc_ftim(IFC_CS3, IFC_FTIM3, CONFIG_SYS_CS3_FTIM3);
+#endif
+}
diff --git a/arch/powerpc/include/asm/config.h b/arch/powerpc/include/asm/config.h
index 2b6b233..536f142 100644
--- a/arch/powerpc/include/asm/config.h
+++ b/arch/powerpc/include/asm/config.h
@@ -75,8 +75,10 @@
 /* Since so many PPC SOCs have a semi-common LBC, define this here */
 #if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) || \
 	defined(CONFIG_MPC83xx)
+#if !defined(CONFIG_FSL_IFC)
 #define CONFIG_FSL_LBC
 #endif
+#endif
 
 /* All PPC boards must swap IDE bytes */
 #define CONFIG_IDE_SWAP_IO
diff --git a/arch/powerpc/include/asm/fsl_ifc.h b/arch/powerpc/include/asm/fsl_ifc.h
new file mode 100644
index 0000000..0464a44
--- /dev/null
+++ b/arch/powerpc/include/asm/fsl_ifc.h
@@ -0,0 +1,947 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Author: Dipen Dudhat <dipen.dudhat at freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ASM_PPC_FSL_IFC_H
+#define __ASM_PPC_FSL_IFC_H
+
+#include <config.h>
+#include <common.h>
+
+/*
+ * CSPR - Chip Select Property Register
+ */
+#define CSPR_BA				0xFFFF0000
+#define CSPR_BA_SHIFT			16
+#define CSPR_PORT_SIZE			0x00000180
+#define CSPR_PORT_SIZE_SHIFT		7
+/* Port Size 8 bit */
+#define CSPR_PORT_SIZE_8		0x00000080
+/* Port Size 16 bit */
+#define CSPR_PORT_SIZE_16		0x00000100
+/* Port Size 32 bit */
+#define CSPR_PORT_SIZE_32		0x00000180
+/* Write Protect */
+#define CSPR_WP				0x00000040
+#define CSPR_WP_SHIFT			6
+/* Machine Select */
+#define CSPR_MSEL			0x00000006
+#define CSPR_MSEL_SHIFT			1
+/* NOR */
+#define CSPR_MSEL_NOR			0x00000000
+/* NAND */
+#define CSPR_MSEL_NAND			0x00000002
+/* GPCM */
+#define CSPR_MSEL_GPCM			0x00000004
+/* Bank Valid */
+#define CSPR_V				0x00000001
+#define CSPR_V_SHIFT			0
+
+/* Convert an address into the right format for the CSPR Registers */
+#define CSPR_PHYS_ADDR(x)		(x & 0xffff0000)
+
+/*
+ * Address Mask Register
+ */
+#define IFC_AMASK_MASK			0xFFFF0000
+#define IFC_AMASK_SHIFT			16
+#define IFC_AMASK(n)			(IFC_AMASK_MASK << \
+					(__ilog2(n) - IFC_AMASK_SHIFT))
+
+/*
+ * Chip Select Option Register IFC_NAND Machine
+ */
+/* Enable ECC Encoder */
+#define CSOR_NAND_ECC_ENC_EN		0x80000000
+/* 4 bit correction per 520 Byte sector */
+#define CSOR_NAND_ECC_MODE_4		0x00000000
+/* 8 bit correction per 528 Byte sector */
+#define CSOR_NAND_ECC_MODE_8		0x10000000
+/* Enable ECC Decoder */
+#define CSOR_NAND_ECC_DEC_EN		0x04000000
+/* Row Address Length */
+#define CSOR_NAND_RAL_MASK		0x01800000
+#define CSOR_NAND_RAL_SHIFT		20
+#define CSOR_NAND_RAL_1			0x00000000
+#define CSOR_NAND_RAL_2			0x00800000
+#define CSOR_NAND_RAL_3			0x01000000
+#define CSOR_NAND_RAL_4			0x01800000
+/* Page Size 512b, 2k, 4k */
+#define CSOR_NAND_PGS_MASK		0x00180000
+#define CSOR_NAND_PGS_SHIFT		16
+#define CSOR_NAND_PGS_512		0x00000000
+#define CSOR_NAND_PGS_2K		0x00080000
+#define CSOR_NAND_PGS_4K		0x00100000
+/* Spare region Size */
+#define CSOR_NAND_SPRZ_MASK		0x0000E000
+#define CSOR_NAND_SPRZ_SHIFT		13
+#define CSOR_NAND_SPRZ_16		0x00000000
+#define CSOR_NAND_SPRZ_64		0x00002000
+#define CSOR_NAND_SPRZ_128		0x00004000
+#define CSOR_NAND_SPRZ_210		0x00006000
+#define CSOR_NAND_SPRZ_218		0x00008000
+#define CSOR_NAND_SPRZ_224		0x0000A000
+/* Pages Per Block */
+#define CSOR_NAND_PB_MASK		0x00000600
+#define CSOR_NAND_PB_SHIFT		8
+#define CSOR_NAND_PB(n)		((__ilog2(n) - 5) << CSOR_NAND_PB_SHIFT)
+/* Time for Read Enable High to Output High Impedance */
+#define CSOR_NAND_TRHZ_MASK		0x0000001C
+#define CSOR_NAND_TRHZ_SHIFT		2
+#define CSOR_NAND_TRHZ_20		0x00000000
+#define CSOR_NAND_TRHZ_40		0x00000004
+#define CSOR_NAND_TRHZ_60		0x00000008
+#define CSOR_NAND_TRHZ_80		0x0000000C
+#define CSOR_NAND_TRHZ_100		0x00000010
+/* Buffer control disable */
+#define CSOR_NAND_BCTLD			0x00000001
+
+/*
+ * Chip Select Option Register - NOR Flash Mode
+ */
+/* Enable Address shift Mode */
+#define CSOR_NOR_ADM_SHFT_MODE_EN	0x80000000
+/* Page Read Enable from NOR device */
+#define CSOR_NOR_PGRD_EN		0x10000000
+/* AVD Toggle Enable during Burst Program */
+#define CSOR_NOR_AVD_TGL_PGM_EN		0x01000000
+/* Address Data Multiplexing Shift */
+#define CSOR_NOR_ADM_MASK		0x0003E000
+#define CSOR_NOR_ADM_SHIFT_SHIFT	13
+#define CSOR_NOR_ADM_SHIFT(n)	((n) << CSOR_NOR_ADM_SHIFT_SHIFT)
+/* Type of the NOR device hooked */
+#define CSOR_NOR_NOR_MODE_AYSNC_NOR	0x00000000
+#define CSOR_NOR_NOR_MODE_AVD_NOR	0x00000020
+/* Time for Read Enable High to Output High Impedance */
+#define CSOR_NOR_TRHZ_MASK		0x0000001C
+#define CSOR_NOR_TRHZ_SHIFT		2
+#define CSOR_NOR_TRHZ_20		0x00000000
+#define CSOR_NOR_TRHZ_40		0x00000004
+#define CSOR_NOR_TRHZ_60		0x00000008
+#define CSOR_NOR_TRHZ_80		0x0000000C
+#define CSOR_NOR_TRHZ_100		0x00000010
+/* Buffer control disable */
+#define CSOR_NOR_BCTLD			0x00000001
+
+/*
+ * Chip Select Option Register - GPCM Mode
+ */
+/* GPCM Mode - Normal */
+#define CSOR_GPCM_GPMODE_NORMAL		0x00000000
+/* GPCM Mode - GenericASIC */
+#define CSOR_GPCM_GPMODE_ASIC		0x80000000
+/* Parity Mode odd/even */
+#define CSOR_GPCM_PARITY_EVEN		0x40000000
+/* Parity Checking enable/disable */
+#define CSOR_GPCM_PAR_EN		0x20000000
+/* GPCM Timeout Count */
+#define CSOR_GPCM_GPTO_MASK		0x0F000000
+#define CSOR_GPCM_GPTO_SHIFT		24
+#define CSOR_GPCM_GPTO(n)	((__ilog2(n) - 8) << CSOR_GPCM_GPTO_SHIFT)
+/* GPCM External Access Termination mode for read access */
+#define CSOR_GPCM_RGETA_EXT		0x00080000
+/* GPCM External Access Termination mode for write access */
+#define CSOR_GPCM_WGETA_EXT		0x00040000
+/* Address Data Multiplexing Shift */
+#define CSOR_GPCM_ADM_MASK		0x0003E000
+#define CSOR_GPCM_ADM_SHIFT_SHIFT	13
+#define CSOR_GPCM_ADM_SHIFT(n)	((n) << CSOR_GPCM_ADM_SHIFT_SHIFT)
+/* Generic ASIC Parity error indication delay */
+#define CSOR_GPCM_GAPERRD_MASK		0x00000180
+#define CSOR_GPCM_GAPERRD_SHIFT		7
+#define CSOR_GPCM_GAPERRD(n)	(((n) - 1) << CSOR_GPCM_GAPERRD_SHIFT)
+/* Time for Read Enable High to Output High Impedance */
+#define CSOR_GPCM_TRHZ_MASK		0x0000001C
+#define CSOR_GPCM_TRHZ_20		0x00000000
+#define CSOR_GPCM_TRHZ_40		0x00000004
+#define CSOR_GPCM_TRHZ_60		0x00000008
+#define CSOR_GPCM_TRHZ_80		0x0000000C
+#define CSOR_GPCM_TRHZ_100		0x00000010
+/* Buffer control disable */
+#define CSOR_GPCM_BCTLD			0x00000001
+
+/*
+ * Flash Timing Registers (FTIM0 - FTIM2_CSn)
+ */
+/*
+ * FTIM0 - NAND Flash Mode
+ */
+#define FTIM0_NAND			0x7EFF3F3F
+#define FTIM0_NAND_TCCST_SHIFT	25
+#define FTIM0_NAND_TCCST(n)	((n) << FTIM0_NAND_TCCST_SHIFT)
+#define FTIM0_NAND_TWP_SHIFT	16
+#define FTIM0_NAND_TWP(n)	((n) << FTIM0_NAND_TWP_SHIFT)
+#define FTIM0_NAND_TWCHT_SHIFT	8
+#define FTIM0_NAND_TWCHT(n)	((n) << FTIM0_NAND_TWCHT_SHIFT)
+#define FTIM0_NAND_TWH_SHIFT	0
+#define FTIM0_NAND_TWH(n)	((n) << FTIM0_NAND_TWH_SHIFT)
+/*
+ * FTIM1 - NAND Flash Mode
+ */
+#define FTIM1_NAND			0xFFFF3FFF
+#define FTIM1_NAND_TADLE_SHIFT	24
+#define FTIM1_NAND_TADLE(n)	((n) << FTIM1_NAND_TADLE_SHIFT)
+#define FTIM1_NAND_TWBE_SHIFT	16
+#define FTIM1_NAND_TWBE(n)	((n) << FTIM1_NAND_TWBE_SHIFT)
+#define FTIM1_NAND_TRR_SHIFT	8
+#define FTIM1_NAND_TRR(n)	((n) << FTIM1_NAND_TRR_SHIFT)
+#define FTIM1_NAND_TRP_SHIFT	0
+#define FTIM1_NAND_TRP(n)	((n) << FTIM1_NAND_TRP_SHIFT)
+/*
+ * FTIM2 - NAND Flash Mode
+ */
+#define FTIM2_NAND			0x1FE1F8FF
+#define FTIM2_NAND_TRAD_SHIFT	21
+#define FTIM2_NAND_TRAD(n)	((n) << FTIM2_NAND_TRAD_SHIFT)
+#define FTIM2_NAND_TREH_SHIFT	11
+#define FTIM2_NAND_TREH(n)	((n) << FTIM2_NAND_TREH_SHIFT)
+#define FTIM2_NAND_TWHRE_SHIFT	8
+#define FTIM2_NAND_TWHRE(n)	((n) << FTIM2_NAND_TWHRE_SHIFT)
+/*
+ * FTIM3 - NAND Flash Mode
+ */
+#define FTIM3_NAND			0xFF000000
+#define FTIM3_NAND_TWW_SHIFT	24
+#define FTIM3_NAND_TWW(n)	((n) << FTIM3_NAND_TWW_SHIFT)
+
+/*
+ * FTIM0 - NOR Flash Mode
+ */
+#define FTIM0_NOR			0xF03F3F3F
+#define FTIM0_NOR_TACSE_SHIFT	28
+#define FTIM0_NOR_TACSE(n)	((n) << FTIM0_NOR_TACSE_SHIFT)
+#define FTIM0_NOR_TEADC_SHIFT	16
+#define FTIM0_NOR_TEADC(n)	((n) << FTIM0_NOR_TEADC_SHIFT)
+#define FTIM0_NOR_TAVDS_SHIFT	8
+#define FTIM0_NOR_TAVDS(n)	((n) << FTIM0_NOR_TAVDS_SHIFT)
+#define FTIM0_NOR_TEAHC_SHIFT	0
+#define FTIM0_NOR_TEAHC(n)	((n) << FTIM0_NOR_TEAHC_SHIFT)
+/*
+ * FTIM1 - NOR Flash Mode
+ */
+#define FTIM1_NOR			0xFF003F3F
+#define FTIM1_NOR_TACO_SHIFT	24
+#define FTIM1_NOR_TACO(n)	((n) << FTIM1_NOR_TACO_SHIFT)
+#define FTIM1_NOR_TRAD_NOR_SHIFT	8
+#define FTIM1_NOR_TRAD_NOR(n)	((n) << FTIM1_NOR_TRAD_NOR_SHIFT)
+#define FTIM1_NOR_TSEQRAD_NOR_SHIFT	0
+#define FTIM1_NOR_TSEQRAD_NOR(n)	((n) << FTIM1_NOR_TSEQRAD_NOR_SHIFT)
+/*
+ * FTIM2 - NOR Flash Mode
+ */
+#define FTIM2_NOR			0x0F3CFCFF
+#define FTIM2_NOR_TCS_SHIFT		24
+#define FTIM2_NOR_TCS(n)	((n) << FTIM2_NOR_TCS_SHIFT)
+#define FTIM2_NOR_TCH_SHIFT		18
+#define FTIM2_NOR_TCH(n)	((n) << FTIM2_NOR_TCH_SHIFT)
+#define FTIM2_NOR_TWPH_SHIFT	10
+#define FTIM2_NOR_TWPH(n)	((n) << FTIM2_NOR_TWPH_SHIFT)
+#define FTIM2_NOR_TWP_SHIFT		0
+#define FTIM2_NOR_TWP(n)	((n) << FTIM2_NOR_TWP_SHIFT)
+
+/*
+ * FTIM0 - Normal GPCM Mode
+ */
+#define FTIM0_GPCM			0xF03F3F3F
+#define FTIM0_GPCM_TACSE_SHIFT	28
+#define FTIM0_GPCM_TACSE(n)	((n) << FTIM0_GPCM_TACSE_SHIFT)
+#define FTIM0_GPCM_TEADC_SHIFT	16
+#define FTIM0_GPCM_TEADC(n)	((n) << FTIM0_GPCM_TEADC_SHIFT)
+#define FTIM0_GPCM_TAVDS_SHIFT	8
+#define FTIM0_GPCM_TAVDS(n)	((n) << FTIM0_GPCM_TAVDS_SHIFT)
+#define FTIM0_GPCM_TEAHC_SHIFT	0
+#define FTIM0_GPCM_TEAHC(n)	((n) << FTIM0_GPCM_TEAHC_SHIFT)
+/*
+ * FTIM1 - Normal GPCM Mode
+ */
+#define FTIM1_GPCM			0xFF003F00
+#define FTIM1_GPCM_TACO_SHIFT	24
+#define FTIM1_GPCM_TACO(n)	((n) << FTIM1_GPCM_TACO_SHIFT)
+#define FTIM1_GPCM_TRAD_SHIFT	8
+#define FTIM1_GPCM_TRAD(n)	((n) << FTIM1_GPCM_TRAD_SHIFT)
+/*
+ * FTIM2 - Normal GPCM Mode
+ */
+#define FTIM2_GPCM			0x0F3C00FF
+#define FTIM2_GPCM_TCS_SHIFT	24
+#define FTIM2_GPCM_TCS(n)	((n) << FTIM2_GPCM_TCS_SHIFT)
+#define FTIM2_GPCM_TCH_SHIFT	18
+#define FTIM2_GPCM_TCH(n)	((n) << FTIM2_GPCM_TCH_SHIFT)
+#define FTIM2_GPCM_TWP_SHIFT	0
+#define FTIM2_GPCM_TWP(n)	((n) << FTIM2_GPCM_TWP_SHIFT)
+
+/*
+ * Ready Busy Status Register (RB_STAT)
+ */
+/* CSn is READY */
+#define IFC_RB_STAT_READY_CS0		0x80000000
+#define IFC_RB_STAT_READY_CS1		0x40000000
+#define IFC_RB_STAT_READY_CS2		0x20000000
+#define IFC_RB_STAT_READY_CS3		0x10000000
+
+/*
+ * General Control Register (GCR)
+ */
+#define IFC_GCR_MASK			0x8000F800
+/* reset all IFC hardware */
+#define IFC_GCR_SOFT_RST_ALL		0x80000000
+/* Turnaroud Time of external buffer */
+#define IFC_GCR_TBCTL_TRN_TIME		0x0000F800
+#define IFC_GCR_TBCTL_TRN_TIME_SHIFT	11
+
+/*
+ * Common Event and Error Status Register (CM_EVTER_STAT)
+ */
+/* Chip select error */
+#define IFC_CM_EVTER_STAT_CSER		0x80000000
+
+/*
+ * Common Event and Error Enable Register (CM_EVTER_EN)
+ */
+/* Chip select error checking enable */
+#define IFC_CM_EVTER_EN_CSEREN		0x80000000
+
+/*
+ * Common Event and Error Interrupt Enable Register (CM_EVTER_INTR_EN)
+ */
+/* Chip select error interrupt enable */
+#define IFC_CM_EVTER_INTR_EN_CSERIREN	0x80000000
+
+/*
+ * Common Transfer Error Attribute Register-0 (CM_ERATTR0)
+ */
+/* transaction type of error Read/Write */
+#define IFC_CM_ERATTR0_ERTYP_READ	0x80000000
+#define IFC_CM_ERATTR0_ERAID		0x0FF00000
+#define IFC_CM_ERATTR0_ESRCID		0x0000FF00
+
+/*
+ * Clock Control Register (CCR)
+ */
+#define IFC_CCR_MASK			0x0F0F8800
+/* Clock division ratio */
+#define IFC_CCR_CLK_DIV_MASK		0x0F000000
+#define IFC_CCR_CLK_DIV_SHIFT		24
+#define IFC_CCR_CLK_DIV(n)		((n-1) << IFC_CCR_CLK_DIV_SHIFT)
+/* IFC Clock Delay */
+#define IFC_CCR_CLK_DLY_MASK		0x000F0000
+#define IFC_CCR_CLK_DLY_SHIFT		16
+#define IFC_CCR_CLK_DLY(n)		((n) << IFC_CCR_CLK_DLY_SHIFT)
+/* Invert IFC clock before sending out */
+#define IFC_CCR_INV_CLK_EN		0x00008000
+/* Fedback IFC Clock */
+#define IFC_CCR_FB_IFC_CLK_SEL		0x00000800
+
+/*
+ * Clock Status Register (CSR)
+ */
+/* Clk is stable */
+#define IFC_CSR_CLK_STAT_STABLE		0x80000000
+
+/*
+ * IFC_NAND Machine Specific Registers
+ */
+/*
+ * NAND Configuration Register (NCFGR)
+ */
+/* Auto Boot Mode */
+#define IFC_NAND_NCFGR_BOOT		0x80000000
+/* Addressing Mode-ROW0+n/COL0 */
+#define IFC_NAND_NCFGR_ADDR_MODE_RC0	0x00000000
+/* Addressing Mode-ROW0+n/COL0+n */
+#define IFC_NAND_NCFGR_ADDR_MODE_RC1	0x00400000
+/* Number of loop iterations of FIR sequences for multi page operations */
+#define IFC_NAND_NCFGR_NUM_LOOP_MASK	0x0000F000
+#define IFC_NAND_NCFGR_NUM_LOOP_SHIFT	12
+#define IFC_NAND_NCFGR_NUM_LOOP(n)	((n) << IFC_NAND_NCFGR_NUM_LOOP_SHIFT)
+/* Number of wait cycles */
+#define IFC_NAND_NCFGR_NUM_WAIT_MASK	0x000000FF
+#define IFC_NAND_NCFGR_NUM_WAIT_SHIFT	0
+
+/*
+ * NAND Flash Command Registers (NAND_FCR0/NAND_FCR1)
+ */
+/* General purpose FCM flash command bytes CMD0-CMD7 */
+#define IFC_NAND_FCR0_CMD0		0xFF000000
+#define IFC_NAND_FCR0_CMD0_SHIFT	24
+#define IFC_NAND_FCR0_CMD1		0x00FF0000
+#define IFC_NAND_FCR0_CMD1_SHIFT	16
+#define IFC_NAND_FCR0_CMD2		0x0000FF00
+#define IFC_NAND_FCR0_CMD2_SHIFT	8
+#define IFC_NAND_FCR0_CMD3		0x000000FF
+#define IFC_NAND_FCR0_CMD3_SHIFT	0
+#define IFC_NAND_FCR1_CMD4		0xFF000000
+#define IFC_NAND_FCR1_CMD4_SHIFT	24
+#define IFC_NAND_FCR1_CMD5		0x00FF0000
+#define IFC_NAND_FCR1_CMD5_SHIFT	16
+#define IFC_NAND_FCR1_CMD6		0x0000FF00
+#define IFC_NAND_FCR1_CMD6_SHIFT	8
+#define IFC_NAND_FCR1_CMD7		0x000000FF
+#define IFC_NAND_FCR1_CMD7_SHIFT	0
+
+/*
+ * Flash ROW and COL Address Register (ROWn, COLn)
+ */
+/* Main/spare region locator */
+#define IFC_NAND_COL_MS			0x80000000
+/* Column Address */
+#define IFC_NAND_COL_CA_MASK		0x00000FFF
+
+/*
+ * NAND Flash Byte Count Register (NAND_BC)
+ */
+/* Byte Count for read/Write */
+#define IFC_NAND_BC			0x000001FF
+
+/*
+ * NAND Flash Instruction Registers (NAND_FIR0/NAND_FIR1/NAND_FIR2)
+ */
+/* NAND Machine specific opcodes OP0-OP14*/
+#define IFC_NAND_FIR0_OP0		0xFC000000
+#define IFC_NAND_FIR0_OP0_SHIFT		26
+#define IFC_NAND_FIR0_OP1		0x03F00000
+#define IFC_NAND_FIR0_OP1_SHIFT		20
+#define IFC_NAND_FIR0_OP2		0x000FC000
+#define IFC_NAND_FIR0_OP2_SHIFT		14
+#define IFC_NAND_FIR0_OP3		0x00003F00
+#define IFC_NAND_FIR0_OP3_SHIFT		8
+#define IFC_NAND_FIR0_OP4		0x000000FC
+#define IFC_NAND_FIR0_OP4_SHIFT		2
+#define IFC_NAND_FIR1_OP5		0xFC000000
+#define IFC_NAND_FIR1_OP5_SHIFT		26
+#define IFC_NAND_FIR1_OP6		0x03F00000
+#define IFC_NAND_FIR1_OP6_SHIFT		20
+#define IFC_NAND_FIR1_OP7		0x000FC000
+#define IFC_NAND_FIR1_OP7_SHIFT		14
+#define IFC_NAND_FIR1_OP8		0x00003F00
+#define IFC_NAND_FIR1_OP8_SHIFT		8
+#define IFC_NAND_FIR1_OP9		0x000000FC
+#define IFC_NAND_FIR1_OP9_SHIFT		2
+#define IFC_NAND_FIR2_OP10		0xFC000000
+#define IFC_NAND_FIR2_OP10_SHIFT	26
+#define IFC_NAND_FIR2_OP11		0x03F00000
+#define IFC_NAND_FIR2_OP11_SHIFT	20
+#define IFC_NAND_FIR2_OP12		0x000FC000
+#define IFC_NAND_FIR2_OP12_SHIFT	14
+#define IFC_NAND_FIR2_OP13		0x00003F00
+#define IFC_NAND_FIR2_OP13_SHIFT	8
+#define IFC_NAND_FIR2_OP14		0x000000FC
+#define IFC_NAND_FIR2_OP14_SHIFT	2
+
+/*
+ * Instruction opcodes to be programmed
+ * in FIR registers- 6bits
+ */
+enum ifc_nand_fir_opcodes {
+	IFC_FIR_OP_NOP,
+	IFC_FIR_OP_CA0,
+	IFC_FIR_OP_CA1,
+	IFC_FIR_OP_CA2,
+	IFC_FIR_OP_CA3,
+	IFC_FIR_OP_RA0,
+	IFC_FIR_OP_RA1,
+	IFC_FIR_OP_RA2,
+	IFC_FIR_OP_RA3,
+	IFC_FIR_OP_CMD0,
+	IFC_FIR_OP_CMD1,
+	IFC_FIR_OP_CMD2,
+	IFC_FIR_OP_CMD3,
+	IFC_FIR_OP_CMD4,
+	IFC_FIR_OP_CMD5,
+	IFC_FIR_OP_CMD6,
+	IFC_FIR_OP_CMD7,
+	IFC_FIR_OP_CW0,
+	IFC_FIR_OP_CW1,
+	IFC_FIR_OP_CW2,
+	IFC_FIR_OP_CW3,
+	IFC_FIR_OP_CW4,
+	IFC_FIR_OP_CW5,
+	IFC_FIR_OP_CW6,
+	IFC_FIR_OP_CW7,
+	IFC_FIR_OP_WBCD,
+	IFC_FIR_OP_RBCD,
+	IFC_FIR_OP_BTRD,
+	IFC_FIR_OP_RDSTAT,
+	IFC_FIR_OP_NWAIT,
+	IFC_FIR_OP_WFR,
+	IFC_FIR_OP_SBRD,
+	IFC_FIR_OP_UA,
+	IFC_FIR_OP_RB,
+};
+
+/*
+ * NAND Operation Sequence Start (NANDSEQ_STRT)
+ */
+/* NAND Flash Operation Start */
+#define IFC_NAND_SEQ_STRT_FIR_STRT	0x80000000
+/* Automatic Erase */
+#define IFC_NAND_SEQ_STRT_AUTO_ERS	0x00800000
+/* Automatic Program */
+#define IFC_NAND_SEQ_STRT_AUTO_PGM	0x00100000
+/* Automatic Copyback */
+#define IFC_NAND_SEQ_STRT_AUTO_CPB	0x00020000
+/* Automatic Read Operation */
+#define IFC_NAND_SEQ_STRT_AUTO_RD	0x00004000
+/* Automatic Status Read */
+#define IFC_NAND_SEQ_STRT_AUTO_STAT_RD	0x00000800
+
+/*
+ * NAND Event and Error Status Register (NAND_EVTER_STAT)
+ */
+/* Operation Complete */
+#define IFC_NAND_EVTER_STAT_OPC		0x80000000
+/* Flash Timeout Error */
+#define IFC_NAND_EVTER_STAT_FTOER	0x08000000
+/* Write Protect Error */
+#define IFC_NAND_EVTER_STAT_WPER	0x04000000
+/* ECC Error */
+#define IFC_NAND_EVTER_STAT_ECCER	0x02000000
+/* RCW Load Done */
+#define IFC_NAND_EVTER_STAT_RCW_DN	0x00008000
+/* Boot Loadr Done */
+#define IFC_NAND_EVTER_STAT_BOOT_DN	0x00004000
+/* Bad Block Indicator search select */
+#define IFC_NAND_EVTER_STAT_BBI_SRCH_SE	0x00000800
+
+/*
+ * NAND Flash Page Read Completion Event Status Register
+ * (PGRDCMPL_EVT_STAT)
+ */
+#define PGRDCMPL_EVT_STAT_MASK		0xFFFF0000
+/* Small Page 0-15 Done */
+#define PGRDCMPL_EVT_STAT_SECTION_SP(n)	(1 << (31 - (n)))
+/* Large Page(2K) 0-3 Done */
+#define PGRDCMPL_EVT_STAT_LP_2K(n)	(0xF << (28 - (n)*4))
+/* Large Page(4K) 0-1 Done */
+#define PGRDCMPL_EVT_STAT_LP_4K(n)	(0xFF << (24 - (n)*8))
+
+/*
+ * NAND Event and Error Enable Register (NAND_EVTER_EN)
+ */
+/* Operation complete event enable */
+#define IFC_NAND_EVTER_EN_OPC_EN	0x80000000
+/* Page read complete event enable */
+#define IFC_NAND_EVTER_EN_PGRDCMPL_EN	0x20000000
+/* Flash Timeout error enable */
+#define IFC_NAND_EVTER_EN_FTOER_EN	0x08000000
+/* Write Protect error enable */
+#define IFC_NAND_EVTER_EN_WPER_EN	0x04000000
+/* ECC error logging enable */
+#define IFC_NAND_EVTER_EN_ECCER_EN	0x02000000
+
+/*
+ * NAND Event and Error Interrupt Enable Register (NAND_EVTER_INTR_EN)
+ */
+/* Enable interrupt for operation complete */
+#define IFC_NAND_EVTER_INTR_OPCIR_EN		0x80000000
+/* Enable interrupt for Page read complete */
+#define IFC_NAND_EVTER_INTR_PGRDCMPLIR_EN	0x20000000
+/* Enable interrupt for Flash timeout error */
+#define IFC_NAND_EVTER_INTR_FTOERIR_EN		0x08000000
+/* Enable interrupt for Write protect error */
+#define IFC_NAND_EVTER_INTR_WPERIR_EN		0x04000000
+/* Enable interrupt for ECC error*/
+#define IFC_NAND_EVTER_INTR_ECCERIR_EN		0x02000000
+
+/*
+ * NAND Transfer Error Attribute Register-0 (NAND_ERATTR0)
+ */
+#define IFC_NAND_ERATTR0_MASK		0x0C080000
+/* Error on CS0-3 for NAND */
+#define IFC_NAND_ERATTR0_ERCS_CS0	0x00000000
+#define IFC_NAND_ERATTR0_ERCS_CS1	0x04000000
+#define IFC_NAND_ERATTR0_ERCS_CS2	0x08000000
+#define IFC_NAND_ERATTR0_ERCS_CS3	0x0C000000
+/* Transaction type of error Read/Write */
+#define IFC_NAND_ERATTR0_ERTTYPE_READ	0x00080000
+
+/*
+ * NAND Flash Status Register (NAND_FSR)
+ */
+/* First byte of data read from read status op */
+#define IFC_NAND_NFSR_RS0		0xFF000000
+/* Second byte of data read from read status op */
+#define IFC_NAND_NFSR_RS1		0x00FF0000
+
+/*
+ * ECC Error Status Registers (ECCSTAT0-ECCSTAT3)
+ */
+/* Number of ECC errors on sector n (n = 0-15) */
+#define IFC_NAND_ECCSTAT0_ERRCNT_SECTOR0_MASK	0x0F000000
+#define IFC_NAND_ECCSTAT0_ERRCNT_SECTOR0_SHIFT	24
+#define IFC_NAND_ECCSTAT0_ERRCNT_SECTOR1_MASK	0x000F0000
+#define IFC_NAND_ECCSTAT0_ERRCNT_SECTOR1_SHIFT	16
+#define IFC_NAND_ECCSTAT0_ERRCNT_SECTOR2_MASK	0x00000F00
+#define IFC_NAND_ECCSTAT0_ERRCNT_SECTOR2_SHIFT	8
+#define IFC_NAND_ECCSTAT0_ERRCNT_SECTOR3_MASK	0x0000000F
+#define IFC_NAND_ECCSTAT0_ERRCNT_SECTOR3_SHIFT	0
+#define IFC_NAND_ECCSTAT1_ERRCNT_SECTOR4_MASK	0x0F000000
+#define IFC_NAND_ECCSTAT1_ERRCNT_SECTOR4_SHIFT	24
+#define IFC_NAND_ECCSTAT1_ERRCNT_SECTOR5_MASK	0x000F0000
+#define IFC_NAND_ECCSTAT1_ERRCNT_SECTOR5_SHIFT	16
+#define IFC_NAND_ECCSTAT1_ERRCNT_SECTOR6_MASK	0x00000F00
+#define IFC_NAND_ECCSTAT1_ERRCNT_SECTOR6_SHIFT	8
+#define IFC_NAND_ECCSTAT1_ERRCNT_SECTOR7_MASK	0x0000000F
+#define IFC_NAND_ECCSTAT1_ERRCNT_SECTOR7_SHIFT	0
+#define IFC_NAND_ECCSTAT2_ERRCNT_SECTOR8_MASK	0x0F000000
+#define IFC_NAND_ECCSTAT2_ERRCNT_SECTOR8_SHIFT	24
+#define IFC_NAND_ECCSTAT2_ERRCNT_SECTOR9_MASK	0x000F0000
+#define IFC_NAND_ECCSTAT2_ERRCNT_SECTOR9_SHIFT	16
+#define IFC_NAND_ECCSTAT2_ERRCNT_SECTOR10_MASK	0x00000F00
+#define IFC_NAND_ECCSTAT2_ERRCNT_SECTOR10_SHIFT	8
+#define IFC_NAND_ECCSTAT2_ERRCNT_SECTOR11_MASK	0x0000000F
+#define IFC_NAND_ECCSTAT2_ERRCNT_SECTOR11_SHIFT	0
+#define IFC_NAND_ECCSTAT3_ERRCNT_SECTOR12_MASK	0x0F000000
+#define IFC_NAND_ECCSTAT3_ERRCNT_SECTOR12_SHIFT	24
+#define IFC_NAND_ECCSTAT3_ERRCNT_SECTOR13_MASK	0x000F0000
+#define IFC_NAND_ECCSTAT3_ERRCNT_SECTOR13_SHIFT	16
+#define IFC_NAND_ECCSTAT3_ERRCNT_SECTOR14_MASK	0x00000F00
+#define IFC_NAND_ECCSTAT3_ERRCNT_SECTOR14_SHIFT	8
+#define IFC_NAND_ECCSTAT3_ERRCNT_SECTOR15_MASK	0x0000000F
+#define IFC_NAND_ECCSTAT3_ERRCNT_SECTOR15_SHIFT	0
+
+/*
+ * NAND Control Register (NANDCR)
+ */
+#define IFC_NAND_NCR_FTOCNT_MASK	0x1E000000
+#define IFC_NAND_NCR_FTOCNT_SHIFT	25
+#define IFC_NAND_NCR_FTOCNT(n)	((_ilog2(n) - 8)  << IFC_NAND_NCR_FTOCNT_SHIFT)
+
+/*
+ * NAND_AUTOBOOT_TRGR
+ */
+/* Trigger RCW load */
+#define IFC_NAND_AUTOBOOT_TRGR_RCW_LD	0x80000000
+/* Trigget Auto Boot */
+#define IFC_NAND_AUTOBOOT_TRGR_BOOT_LD	0x20000000
+
+/*
+ * NAND_MDR
+ */
+/* 1st read data byte when opcode SBRD */
+#define IFC_NAND_MDR_RDATA0		0xFF000000
+/* 2nd read data byte when opcode SBRD */
+#define IFC_NAND_MDR_RDATA1		0x00FF0000
+
+/*
+ * NOR Machine Specific Registers
+ */
+/*
+ * NOR Event and Error Status Register (NOR_EVTER_STAT)
+ */
+/* NOR Command Sequence Operation Complete */
+#define IFC_NOR_EVTER_STAT_OPC_NOR	0x80000000
+/* Write Protect Error */
+#define IFC_NOR_EVTER_STAT_WPER		0x04000000
+/* Command Sequence Timeout Error */
+#define IFC_NOR_EVTER_STAT_STOER	0x01000000
+
+/*
+ * NOR Event and Error Enable Register (NOR_EVTER_EN)
+ */
+/* NOR Command Seq complete event enable */
+#define IFC_NOR_EVTER_EN_OPCEN_NOR	0x80000000
+/* Write Protect Error Checking Enable */
+#define IFC_NOR_EVTER_EN_WPEREN		0x04000000
+/* Timeout Error Enable */
+#define IFC_NOR_EVTER_EN_STOEREN	0x01000000
+
+/*
+ * NOR Event and Error Interrupt Enable Register (NOR_EVTER_INTR_EN)
+ */
+/* Enable interrupt for OPC complete */
+#define IFC_NOR_EVTER_INTR_OPCEN_NOR	0x80000000
+/* Enable interrupt for write protect error */
+#define IFC_NOR_EVTER_INTR_WPEREN	0x04000000
+/* Enable interrupt for timeout error */
+#define IFC_NOR_EVTER_INTR_STOEREN	0x01000000
+
+/*
+ * NOR Transfer Error Attribute Register-0 (NOR_ERATTR0)
+ */
+/* Source ID for error transaction */
+#define IFC_NOR_ERATTR0_ERSRCID		0xFF000000
+/* AXI ID for error transation */
+#define IFC_NOR_ERATTR0_ERAID		0x000FF000
+/* Chip select corresponds to NOR error */
+#define IFC_NOR_ERATTR0_ERCS_CS0	0x00000000
+#define IFC_NOR_ERATTR0_ERCS_CS1	0x00000010
+#define IFC_NOR_ERATTR0_ERCS_CS2	0x00000020
+#define IFC_NOR_ERATTR0_ERCS_CS3	0x00000030
+/* Type of transaction read/write */
+#define IFC_NOR_ERATTR0_ERTYPE_READ	0x00000001
+
+/*
+ * NOR Transfer Error Attribute Register-2 (NOR_ERATTR2)
+ */
+#define IFC_NOR_ERATTR2_ER_NUM_PHASE_EXP	0x000F0000
+#define IFC_NOR_ERATTR2_ER_NUM_PHASE_PER	0x00000F00
+
+/*
+ * NOR Control Register (NORCR)
+ */
+#define IFC_NORCR_MASK			0x0F0F0000
+/* No. of Address/Data Phase */
+#define IFC_NORCR_NUM_PHASE_MASK	0x0F000000
+#define IFC_NORCR_NUM_PHASE_SHIFT	24
+#define IFC_NORCR_NUM_PHASE(n)	((n-1) << IFC_NORCR_NUM_PHASE_SHIFT)
+/* Sequence Timeout Count */
+#define IFC_NORCR_STOCNT_MASK		0x000F0000
+#define IFC_NORCR_STOCNT_SHIFT		16
+#define IFC_NORCR_STOCNT(n)	((__ilog2(n) - 8) << IFC_NORCR_STOCNT_SHIFT)
+
+/*
+ * GPCM Machine specific registers
+ */
+/*
+ * GPCM Event and Error Status Register (GPCM_EVTER_STAT)
+ */
+/* Timeout error */
+#define IFC_GPCM_EVTER_STAT_TOER	0x04000000
+/* Parity error */
+#define IFC_GPCM_EVTER_STAT_PER		0x01000000
+
+/*
+ * GPCM Event and Error Enable Register (GPCM_EVTER_EN)
+ */
+/* Timeout error enable */
+#define IFC_GPCM_EVTER_EN_TOER_EN	0x04000000
+/* Parity error enable */
+#define IFC_GPCM_EVTER_EN_PER_EN	0x01000000
+
+/*
+ * GPCM Event and Error Interrupt Enable Register (GPCM_EVTER_INTR_EN)
+ */
+/* Enable Interrupt for timeout error */
+#define IFC_GPCM_EEIER_TOERIR_EN	0x04000000
+/* Enable Interrupt for Parity error */
+#define IFC_GPCM_EEIER_PERIR_EN		0x01000000
+
+/*
+ * GPCM Transfer Error Attribute Register-0 (GPCM_ERATTR0)
+ */
+/* Source ID for error transaction */
+#define IFC_GPCM_ERATTR0_ERSRCID	0xFF000000
+/* AXI ID for error transaction */
+#define IFC_GPCM_ERATTR0_ERAID		0x000FF000
+/* Chip select corresponds to GPCM error */
+#define IFC_GPCM_ERATTR0_ERCS_CS0	0x00000000
+#define IFC_GPCM_ERATTR0_ERCS_CS1	0x00000040
+#define IFC_GPCM_ERATTR0_ERCS_CS2	0x00000080
+#define IFC_GPCM_ERATTR0_ERCS_CS3	0x000000C0
+/* Type of transaction read/Write */
+#define IFC_GPCM_ERATTR0_ERTYPE_READ	0x00000001
+
+/*
+ * GPCM Transfer Error Attribute Register-2 (GPCM_ERATTR2)
+ */
+/* On which beat of address/data parity error is observed */
+#define IFC_GPCM_ERATTR2_PERR_BEAT		0x00000C00
+/* Parity Error on byte */
+#define IFC_GPCM_ERATTR2_PERR_BYTE		0x000000F0
+/* Parity Error reported in addr or data phase */
+#define IFC_GPCM_ERATTR2_PERR_DATA_PHASE	0x00000001
+
+/*
+ * GPCM Status Register (GPCM_STAT)
+ */
+#define IFC_GPCM_STAT_BSY		0x80000000  /* GPCM is busy */
+
+
+#ifndef __ASSEMBLY__
+#include <asm/io.h>
+
+extern void print_ifc_regs(void);
+extern void init_early_memctl_regs(void);
+
+#define IFC_BASE_ADDR ((struct fsl_ifc *)CONFIG_SYS_IFC_ADDR)
+
+#define get_ifc_cspr(i) (in_be32(&(IFC_BASE_ADDR)->cspr_cs[i].cspr))
+#define get_ifc_csor(i) (in_be32(&(IFC_BASE_ADDR)->csor_cs[i].csor))
+#define get_ifc_amask(i) (in_be32(&(IFC_BASE_ADDR)->amask_cs[i].amask))
+#define get_ifc_ftim(i, j) (in_be32(&(IFC_BASE_ADDR)->ftim_cs[i].ftim[j]))
+
+#define set_ifc_cspr(i, v) (out_be32(&(IFC_BASE_ADDR)->cspr_cs[i].cspr, v))
+#define set_ifc_csor(i, v) (out_be32(&(IFC_BASE_ADDR)->csor_cs[i].csor, v))
+#define set_ifc_amask(i, v) (out_be32(&(IFC_BASE_ADDR)->amask_cs[i].amask, v))
+#define set_ifc_ftim(i, j, v) \
+			(out_be32(&(IFC_BASE_ADDR)->ftim_cs[i].ftim[j], v))
+
+#define FSL_IFC_BANK_COUNT	4
+
+enum ifc_chip_sel {
+	IFC_CS0,
+	IFC_CS1,
+	IFC_CS2,
+	IFC_CS3,
+};
+
+enum ifc_ftims {
+	IFC_FTIM0,
+	IFC_FTIM1,
+	IFC_FTIM2,
+	IFC_FTIM3,
+};
+
+/*
+ * IFC Controller NAND Machine registers
+ */
+struct fsl_ifc_nand {
+	u32 ncfgr;
+	u32 res1[0x4];
+	u32 nand_fcr0;
+	u32 nand_fcr1;
+	u32 res2[0x8];
+	u32 row0;
+	u32 res3;
+	u32 col0;
+	u32 res4;
+	u32 row1;
+	u32 res5;
+	u32 col1;
+	u32 res6;
+	u32 row2;
+	u32 res7;
+	u32 col2;
+	u32 res8;
+	u32 row3;
+	u32 res9;
+	u32 col3;
+	u32 res10[0x9];
+	u32 nand_fbcr;
+	u32 res11;
+	u32 nand_fir0;
+	u32 nand_fir1;
+	u32 nand_fir2;
+	u32 res12[0x10];
+	u32 nand_csel;
+	u32 res13;
+	u32 nandseq_strt;
+	u32 res14;
+	u32 nand_evter_stat;
+	u32 res15;
+	u32 pgrdcmpl_evt_stat;
+	u32 res16[0x2];
+	u32 nand_evter_en;
+	u32 res17[0x2];
+	u32 nand_evter_intr_en;
+	u32 res18[0x2];
+	u32 nand_erattr0;
+	u32 nand_erattr1;
+	u32 res19[0x10];
+	u32 nand_fsr;
+	u32 res20;
+	u32 nand_eccstat0;
+	u32 nand_eccstat1;
+	u32 nand_eccstat2;
+	u32 nand_eccstat3;
+	u32 res21[0x20];
+	u32 nanndcr;
+	u32 res22[0x2];
+	u32 nand_autoboot_trgr;
+	u32 res23;
+	u32 nand_mdr;
+	u32 res24[0x5C];
+};
+
+/*
+ * IFC controller NOR Machine registers
+ */
+struct fsl_ifc_nor {
+	u32 nor_evter_stat;
+	u32 res1[0x2];
+	u32 nor_evter_en;
+	u32 res2[0x2];
+	u32 nor_evter_intr_en;
+	u32 res3[0x2];
+	u32 nor_erattr0;
+	u32 nor_erattr1;
+	u32 nor_erattr2;
+	u32 res4[0x2];
+	u32 norcr;
+	u32 res5[0xEF];
+};
+
+/*
+ * IFC controller GPCM Machine registers
+ */
+struct fsl_ifc_gpcm {
+	u32 gpcm_evter_stat;
+	u32 res1[0x2];
+	u32 gpcm_evter_en;
+	u32 res2[0x2];
+	u32 gpcm_evter_intr_en;
+	u32 res3[0x2];
+	u32 gpcm_erattr0;
+	u32 gpcm_erattr1;
+	u32 gpcm_erattr2;
+	u32 gpcm_stat;
+	u32 res4[0x1F3];
+};
+
+
+/*
+ * IFC Controller Registers
+ */
+struct fsl_ifc {
+	u32 ifc_rev;
+	u32 res1[0x3];
+	struct {
+		u32 cspr;
+		u32 res2[0x2];
+	} cspr_cs[FSL_IFC_BANK_COUNT];
+	u32 res3[0x18];
+	struct {
+		u32 amask;
+		u32 res4[0x2];
+	} amask_cs[FSL_IFC_BANK_COUNT];
+	u32 res5[0x18];
+	struct {
+		u32 csor;
+		u32 res6[0x2];
+	} csor_cs[FSL_IFC_BANK_COUNT];
+	u32 res7[0x18];
+	struct {
+		u32 ftim[4];
+		u32 res8[0x8];
+	} ftim_cs[FSL_IFC_BANK_COUNT];
+	u32 res9[0x60];
+	u32 rb_stat;
+	u32 res10[0x2];
+	u32 ifc_gcr;
+	u32 res11[0x2];
+	u32 cm_evter_stat;
+	u32 res12[0x2];
+	u32 cm_evter_en;
+	u32 res13[0x2];
+	u32 cm_evter_intr_en;
+	u32 res14[0x2];
+	u32 cm_erattr0;
+	u32 cm_erattr1;
+	u32 res15[0x2];
+	u32 ifc_ccr;
+	u32 ifc_csr;
+	u32 res16[0x2EB];
+	struct fsl_ifc_nand ifc_nand;
+	struct fsl_ifc_nor ifc_nor;
+	struct fsl_ifc_gpcm ifc_gpcm;
+};
+
+#endif /* __ASSEMBLY__ */
+#endif /* __ASM_PPC_FSL_IFC_H */
diff --git a/arch/powerpc/include/asm/fsl_law.h b/arch/powerpc/include/asm/fsl_law.h
index 6a4279c..e308b15 100644
--- a/arch/powerpc/include/asm/fsl_law.h
+++ b/arch/powerpc/include/asm/fsl_law.h
@@ -91,6 +91,7 @@ enum law_trgt_if {
 #define LAW_TRGT_IF_PCIX	LAW_TRGT_IF_PCI
 #define LAW_TRGT_IF_PCIE_2	LAW_TRGT_IF_PCI_2
 #define LAW_TRGT_IF_RIO_1	LAW_TRGT_IF_RIO
+#define LAW_TRGT_IF_IFC		LAW_TRGT_IF_LBC
 
 #ifdef CONFIG_MPC8641
 #define LAW_TRGT_IF_PCIE_1	LAW_TRGT_IF_PCI
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index 6bd83ba..a30a58c 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -31,6 +31,7 @@
 #include <asm/types.h>
 #include <asm/fsl_dma.h>
 #include <asm/fsl_i2c.h>
+#include <asm/fsl_ifc.h>
 #include <asm/fsl_lbc.h>
 #include <asm/fsl_fman.h>
 
@@ -2227,6 +2228,7 @@ typedef struct ccsr_pme {
 #define CONFIG_SYS_MPC85xx_GPIO_OFFSET		0xF000
 #define CONFIG_SYS_MPC85xx_SATA1_OFFSET		0x18000
 #define CONFIG_SYS_MPC85xx_SATA2_OFFSET		0x19000
+#define CONFIG_SYS_MPC85xx_IFC_OFFSET		0x1e000
 #define CONFIG_SYS_MPC85xx_L2_OFFSET		0x20000
 #define CONFIG_SYS_MPC85xx_DMA_OFFSET		0x21000
 #define CONFIG_SYS_MPC85xx_USB_OFFSET		0x22000
@@ -2269,6 +2271,8 @@ typedef struct ccsr_pme {
 	(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_DDR2_OFFSET)
 #define CONFIG_SYS_LBC_ADDR \
 	(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_LBC_OFFSET)
+#define CONFIG_SYS_IFC_ADDR \
+	(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_IFC_OFFSET)
 #define CONFIG_SYS_MPC85xx_ESPI_ADDR \
 	(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_ESPI_OFFSET)
 #define CONFIG_SYS_MPC85xx_PCIX_ADDR \
-- 
1.5.6.5




More information about the U-Boot mailing list