[U-Boot] [PATCH 2/2] at91: fixed 'esd gmbh' meesc and otc570 boards

Daniel Gorsulowski Daniel.Gorsulowski at esd.eu
Fri Jan 21 10:12:16 CET 2011


Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski at esd.eu>
---

There is still a bug in USART config. This patch is for reviewing only!

 board/esd/meesc/config.mk  |    1 -
 board/esd/meesc/meesc.c    |   39 +++++-----
 board/esd/otc570/config.mk |    1 -
 board/esd/otc570/otc570.c  |   51 +++++++------
 boards.cfg                 |    6 +-
 include/configs/meesc.h    |  150 ++++++++++++++++++++++---------------
 include/configs/otc570.h   |  179 +++++++++++++++++++++++++-------------------
 7 files changed, 241 insertions(+), 186 deletions(-)
 delete mode 100644 board/esd/meesc/config.mk
 delete mode 100644 board/esd/otc570/config.mk

diff --git a/board/esd/meesc/config.mk b/board/esd/meesc/config.mk
deleted file mode 100644
index 2077692..0000000
--- a/board/esd/meesc/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x21f00000
diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
index 41fa3e1..46cd33c 100644
--- a/board/esd/meesc/meesc.c
+++ b/board/esd/meesc/meesc.c
@@ -3,7 +3,7 @@
  * Stelian Pop <stelian.pop at leadtechdesign.com>
  * Lead Tech Design <www.leadtechdesign.com>
  *
- * (C) Copyright 2009-2010
+ * (C) Copyright 2009-2011
  * Daniel Gorsulowski <daniel.gorsulowski at esd.eu>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -27,6 +27,7 @@
  */
 
 #include <common.h>
+#include <asm/io.h>
 #include <asm/arch/at91sam9263.h>
 #include <asm/arch/at91sam9_smc.h>
 #include <asm/arch/at91_common.h>
@@ -36,7 +37,6 @@
 #include <asm/arch/at91_pio.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/io.h>
 #include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -67,8 +67,8 @@ int get_hw_rev(void)
 static void meesc_nand_hw_init(void)
 {
 	unsigned long csa;
-	at91_smc_t 	*smc 	= (at91_smc_t *) AT91_SMC0_BASE;
-	at91_matrix_t 	*matrix = (at91_matrix_t *) AT91_MATRIX_BASE;
+	at91_smc_t 	*smc 	= (at91_smc_t *) ATMEL_BASE_SMC0;
+	at91_matrix_t 	*matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
 
 	/* Enable CS3 */
 	csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
@@ -88,7 +88,7 @@ static void meesc_nand_hw_init(void)
 	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
 		AT91_SMC_MODE_EXNW_DISABLE |
 		AT91_SMC_MODE_DBW_8 |
-		AT91_SMC_MODE_TDF_CYCLE(2),
+		AT91_SMC_MODE_TDF_CYCLE(3),
 		&smc->cs[3].mode);
 
 	/* Configure RDY/BSY */
@@ -102,9 +102,9 @@ static void meesc_nand_hw_init(void)
 #ifdef CONFIG_MACB
 static void meesc_macb_hw_init(void)
 {
-	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) ATMEL_BASE_PMC;
 	/* Enable clock */
-	writel(1 << AT91SAM9263_ID_EMAC, &pmc->pcer);
+	writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
 	at91_macb_hw_init();
 }
 #endif
@@ -117,7 +117,7 @@ static void meesc_macb_hw_init(void)
  */
 static void meesc_ethercat_hw_init(void)
 {
-	at91_smc_t 	*smc1 	= (at91_smc_t *) AT91_SMC1_BASE;
+	at91_smc_t 	*smc1 	= (at91_smc_t *) ATMEL_BASE_SMC1;
 
 	/* Configure SMC EBI1_CS0 for EtherCAT */
 	writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
@@ -142,8 +142,9 @@ static void meesc_ethercat_hw_init(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = get_ram_size((long *) PHYS_SDRAM, (1 << 27));
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE,
+					(1 << 27));
 	return 0;
 }
 
@@ -151,7 +152,7 @@ int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
 #ifdef CONFIG_MACB
-	rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x00);
+	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
 #endif
 	return rc;
 }
@@ -225,7 +226,7 @@ int misc_init_r(void)
 {
 	char		*str;
 	char		buf[32];
-	at91_pmc_t	*pmc = (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
 
 	/*
 	 * Normally the processor clock has a divisor of 2.
@@ -248,22 +249,22 @@ int misc_init_r(void)
 
 int board_init(void)
 {
-	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) ATMEL_BASE_PMC;
 
 	/* Peripheral Clock Enable Register */
-	writel(1 << AT91SAM9263_ID_PIOA |
-		1 << AT91SAM9263_ID_PIOB |
-		1 << AT91SAM9263_ID_PIOCDE |
-		1 << AT91SAM9263_ID_UHP,
+	writel(1 << ATMEL_ID_PIOA |
+		1 << ATMEL_ID_PIOB |
+		1 << ATMEL_ID_PIOCDE |
+		1 << ATMEL_ID_UHP,
 		&pmc->pcer);
 
 	/* initialize ET1100 Controller */
 	meesc_ethercat_hw_init();
 
 	/* adress of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
-	at91_serial_hw_init();
+	at91_seriald_hw_init();
 #ifdef CONFIG_CMD_NAND
 	meesc_nand_hw_init();
 #endif
diff --git a/board/esd/otc570/config.mk b/board/esd/otc570/config.mk
deleted file mode 100644
index e554a45..0000000
--- a/board/esd/otc570/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x23f00000
diff --git a/board/esd/otc570/otc570.c b/board/esd/otc570/otc570.c
index 410d8b4..c66f99e 100644
--- a/board/esd/otc570/otc570.c
+++ b/board/esd/otc570/otc570.c
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2010
+ * (C) Copyright 2010-2011
  * Daniel Gorsulowski <daniel.gorsulowski at esd.eu>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -27,6 +27,7 @@
  */
 
 #include <common.h>
+#include <asm/io.h>
 #include <asm/arch/at91sam9263.h>
 #include <asm/arch/at91sam9_smc.h>
 #include <asm/arch/at91_common.h>
@@ -36,7 +37,6 @@
 #include <asm/arch/at91_pio.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/io.h>
 #include <atmel_lcdc.h>
 #include <lcd.h>
 #include <netdev.h>
@@ -73,8 +73,8 @@ int get_hw_rev(void)
 static void otc570_nand_hw_init(void)
 {
 	unsigned long csa;
-	at91_smc_t 	*smc 	= (at91_smc_t *) AT91_SMC0_BASE;
-	at91_matrix_t 	*matrix = (at91_matrix_t *) AT91_MATRIX_BASE;
+	at91_smc_t 	*smc 	= (at91_smc_t *) ATMEL_BASE_SMC0;
+	at91_matrix_t 	*matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
 
 	/* Enable CS3 */
 	csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
@@ -94,7 +94,7 @@ static void otc570_nand_hw_init(void)
 	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
 		AT91_SMC_MODE_EXNW_DISABLE |
 		       AT91_SMC_MODE_DBW_8 |
-		       AT91_SMC_MODE_TDF_CYCLE(2),
+		       AT91_SMC_MODE_TDF_CYCLE(3),
 		&smc->cs[3].mode);
 
 	/* Configure RDY/BSY */
@@ -108,9 +108,9 @@ static void otc570_nand_hw_init(void)
 #ifdef CONFIG_MACB
 static void otc570_macb_hw_init(void)
 {
-	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) ATMEL_BASE_PMC;
 	/* Enable clock */
-	writel(1 << AT91SAM9263_ID_EMAC, &pmc->pcer);
+	writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
 	at91_macb_hw_init();
 }
 #endif
@@ -123,7 +123,7 @@ static void otc570_macb_hw_init(void)
  */
 static void otc570_ethercat_hw_init(void)
 {
-	at91_smc_t 	*smc1 	= (at91_smc_t *) AT91_SMC1_BASE;
+	at91_smc_t 	*smc1 	= (at91_smc_t *) ATMEL_BASE_SMC1;
 
 	/* Configure SMC EBI1_CS0 for EtherCAT */
 	writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
@@ -179,7 +179,7 @@ void lcd_disable(void)
 
 static void otc570_lcd_hw_init(void)
 {
-	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) ATMEL_BASE_PMC;
 
 	at91_set_a_periph(AT91_PIO_PORTC, 0, 0);	/* LCDVSYNC */
 	at91_set_a_periph(AT91_PIO_PORTC, 1, 0);	/* LCDHSYNC */
@@ -206,7 +206,7 @@ static void otc570_lcd_hw_init(void)
 	at91_set_a_periph(AT91_PIO_PORTC, 27, 0);	/* LCDD23 */
 	at91_set_pio_output(AT91_PIO_PORTA, 30, 1);	/* PCI */
 
-	writel(1 << AT91SAM9263_ID_LCDC, &pmc->pcer);
+	writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
 	gd->fb_base = CONFIG_OTC570_LCD_BASE;
 }
 
@@ -239,8 +239,9 @@ void lcd_show_board_info(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = get_ram_size((long *) PHYS_SDRAM, (1 << 27));
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->bd->bi_dram[0].size = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE,
+					(1 << 27));
 	return 0;
 }
 
@@ -248,7 +249,7 @@ int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
 #ifdef CONFIG_MACB
-	rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x00);
+	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
 #endif
 	return rc;
 }
@@ -297,12 +298,12 @@ u32 get_board_rev(void)
 int misc_init_r(void)
 {
 	char		str[64];
-	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) ATMEL_BASE_PMC;
 
 	at91_set_pio_output(AT91_PIO_PORTA, 29, 1);
 	at91_set_a_periph(AT91_PIO_PORTA, 26, 1);	/* TXD0 */
 	at91_set_a_periph(AT91_PIO_PORTA, 27, 0);	/* RXD0 */
-	writel(1 << AT91SAM9263_ID_US0,	&pmc->pcer);
+	writel(1 << ATMEL_ID_US0,	&pmc->pcer);
 	/* Set USART_MODE = 1 (RS485) */
 	writel(1, 0xFFF8C004);
 
@@ -333,25 +334,25 @@ int misc_init_r(void)
 
 int board_init(void)
 {
-	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) ATMEL_BASE_PMC;
 
 	/* Peripheral Clock Enable Register */
-	writel(	1 << AT91SAM9263_ID_PIOA |
-		1 << AT91SAM9263_ID_PIOB |
-		1 << AT91SAM9263_ID_PIOCDE |
-		1 << AT91SAM9263_ID_TWI |
-		1 << AT91SAM9263_ID_SPI0 |
-		1 << AT91SAM9263_ID_LCDC |
-		1 << AT91SAM9263_ID_UHP,
+	writel(	1 << ATMEL_ID_PIOA |
+		1 << ATMEL_ID_PIOB |
+		1 << ATMEL_ID_PIOCDE |
+		1 << ATMEL_ID_TWI |
+		1 << ATMEL_ID_SPI0 |
+		1 << ATMEL_ID_LCDC |
+		1 << ATMEL_ID_UHP,
 		&pmc->pcer);
 
 	/* arch number of OTC570-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_OTC570;
 
 	/* adress of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
-	at91_serial_hw_init();
+	at91_seriald_hw_init();
 #ifdef CONFIG_CMD_NAND
 	otc570_nand_hw_init();
 #endif
diff --git a/boards.cfg b/boards.cfg
index 9b15026..77f3fc4 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -83,8 +83,10 @@ at91sam9xeek_dataflash_cs0   arm         arm926ejs   at91sam9260ek       atmel
 at91sam9xeek_dataflash_cs1   arm         arm926ejs   at91sam9260ek       atmel          at91        at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS1
 top9000eval_xe               arm         arm926ejs   top9000             emk            at91        top9000:EVAL9000
 top9000su_xe                 arm         arm926ejs   top9000             emk            at91        top9000:SU9000
-meesc                        arm         arm926ejs   -                   esd            at91
-otc570                       arm         arm926ejs   -                   esd            at91
+meesc                        arm         arm926ejs   meesc               esd            at91        meesc:AT91SAM9263,SYS_USE_NANDFLASH
+meesc_dataflash              arm         arm926ejs   meesc               esd            at91        meesc:AT91SAM9263,SYS_USE_DATAFLASH
+otc570                       arm         arm926ejs   otc570              esd            at91        otc570:AT91SAM9263,SYS_USE_NANDFLASH
+otc570_dataflash             arm         arm926ejs   otc570              esd            at91        otc570:AT91SAM9263,SYS_USE_DATAFLASH
 pm9261                       arm         arm926ejs   -                   ronetix        at91
 pm9263                       arm         arm926ejs   -                   ronetix        at91
 da830evm                     arm         arm926ejs   da8xxevm            davinci        davinci
diff --git a/include/configs/meesc.h b/include/configs/meesc.h
index a27b36b..dbb97ed 100644
--- a/include/configs/meesc.h
+++ b/include/configs/meesc.h
@@ -3,7 +3,7 @@
  * Stelian Pop <stelian.pop at leadtechdesign.com>
  * Lead Tech Design <www.leadtechdesign.com>
  *
- * (C) Copyright 2009-2010
+ * (C) Copyright 2009-2011
  * Daniel Gorsulowski <daniel.gorsulowski at esd.eu>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -31,49 +31,67 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/* Common stuff */
-#define CONFIG_MEESC			1	/* Board is esd MEESC */
-#define CONFIG_ARM926EJS		1	/* This is an ARM926EJS Core */
-#define CONFIG_AT91SAM9263		1	/* It's an AT91SAM9263 SoC */
-#define CONFIG_SYS_AT91_MAIN_CLOCK	16000000/* 16.0 MHz crystal */
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
+
+/*
+ * Warning: changing CONFIG_SYS_TEXT_BASE requires
+ * adapting the initial boot program.
+ * Since the linker has to swallow that define, we must use a pure
+ * hex number here!
+ */
+#define CONFIG_SYS_TEXT_BASE		0x21f00000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768	/* slow clock xtal */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	16000000/* main clock xtal */
 #define CONFIG_SYS_HZ			1000	/* decrementer freq */
-#define CONFIG_DISPLAY_BOARDINFO	1
-#define CONFIG_DISPLAY_CPUINFO		1	/* display cpu info and speed */
-#define CONFIG_PREBOOT				/* enable preboot variable */
-#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-#define CONFIG_SERIAL_TAG		1
-#define CONFIG_REVISION_TAG		1
-#undef CONFIG_USE_IRQ				/* don't need IRQ/FIQ stuff */
 
-#define CONFIG_SKIP_LOWLEVEL_INIT
+/* Misc CPU related */
+#undef	CONFIG_USE_IRQ				/* don't need IRQ/FIQ stuff */
+#define CONFIG_MEESC				/* Board is esd MEESC */
 #define CONFIG_MISC_INIT_R			/* Call misc_init_r */
-
+#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
+#define CONFIG_PREBOOT				/* enable preboot variable */
+#define CONFIG_DISPLAY_CPUINFO			/* display cpu info and speed */
+#define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_ARCH_CPU_INIT
+#define CONFIG_SERIAL_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
 
 /*
  * Hardware drivers
  */
 
+/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is reworked */
+#define ATMEL_PMC_UHP			AT91SAM926x_PMC_UHP
+
+/* general purpose I/O */
+#define CONFIG_AT91_GPIO
+
 /* Console output */
-#define CONFIG_AT91_GPIO			1
-#define CONFIG_ATMEL_USART			1
-#undef CONFIG_USART0
-#undef CONFIG_USART1
-#undef CONFIG_USART2
-#define CONFIG_USART3				1	/* USART 3 is DBGU */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define CONFIG_USART_ID			ATMEL_ID_SYS
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{115200, 19200, 38400, 57600, 9600}
 
-#define CONFIG_BOOTDELAY			3
-#define CONFIG_ZERO_BOOTDELAY_CHECK		1
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
 
 /*
  * BOOTP options
  */
-#define CONFIG_BOOTP_BOOTFILESIZE		1
-#define CONFIG_BOOTP_BOOTPATH			1
-#define CONFIG_BOOTP_GATEWAY			1
-#define CONFIG_BOOTP_HOSTNAME			1
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
 
 /*
  * Command line configuration.
@@ -84,21 +102,25 @@
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_IMLS
 
-#define CONFIG_CMD_PING				1
-#define CONFIG_CMD_DHCP				1
-#define CONFIG_CMD_NAND				1
-#define CONFIG_CMD_USB				1
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_USB
 
 /* LED */
-#define CONFIG_AT91_LED				1
+#define CONFIG_AT91_LED
 
 /* SDRAM */
-#define CONFIG_NR_DRAM_BANKS			1
-#define PHYS_SDRAM				0x20000000
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		0x20000000
+
+/* Initial stack pointer */
+#define CONFIG_SYS_INIT_SP_ADDR	\
+	(CONFIG_SYS_TEXT_BASE - GENERATED_GBL_DATA_SIZE)
 
 /* DataFlash */
 #define CONFIG_ATMEL_DATAFLASH_SPI
-#define CONFIG_HAS_DATAFLASH			1
+#define CONFIG_HAS_DATAFLASH
 #define CONFIG_SYS_SPI_WRITE_TOUT		(5 * CONFIG_SYS_HZ)
 #define CONFIG_SYS_MAX_DATAFLASH_BANKS		1
 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0	0xC0000000	/* CS0 */
@@ -107,14 +129,14 @@
 #define DATAFLASH_TCHS				(0x1 << 24)
 
 /* NOR flash is not populated, disable it */
-#define CONFIG_SYS_NO_FLASH			1
+#define CONFIG_SYS_NO_FLASH
 
 /* NAND flash */
 #ifdef CONFIG_CMD_NAND
 #define CONFIG_NAND_ATMEL
 #define CONFIG_SYS_MAX_NAND_DEVICE		1
 #define CONFIG_SYS_NAND_BASE			0x40000000
-#define CONFIG_SYS_NAND_DBW_8			1
+#define CONFIG_SYS_NAND_DBW_8
 /* our ALE is AD21 */
 #define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
 /* our CLE is AD22 */
@@ -125,39 +147,39 @@
 #endif
 
 /* Ethernet */
-#define CONFIG_MACB				1
-#define CONFIG_RMII				1
-#define CONFIG_NET_MULTI			1
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_MULTI
+#define CONFIG_FIT
 #define CONFIG_NET_RETRY_COUNT			20
 #undef CONFIG_RESET_PHY_R
 
 /* USB */
 #define CONFIG_USB_ATMEL
-#define CONFIG_USB_OHCI_NEW			1
-#define CONFIG_DOS_PARTITION			1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT		1
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
 #define CONFIG_SYS_USB_OHCI_REGS_BASE		0x00a00000
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME		"at91sam9263"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
-#define CONFIG_USB_STORAGE			1
-#define CONFIG_CMD_FAT				1
-
-#define CONFIG_SYS_LOAD_ADDR			0x22000000 /* load address */
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_FAT
 
-#define CONFIG_SYS_MEMTEST_START		PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END			0x21e00000
+#define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */
 
-#define CONFIG_SYS_USE_DATAFLASH		1
-#undef CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		0x21e00000
 
 /* CAN */
-#define CONFIG_AT91_CAN				1
+#define CONFIG_AT91_CAN
 
 /* hw-controller addresses */
-#define CONFIG_ET1100_BASE			0x70000000
+#define CONFIG_ET1100_BASE		0x70000000 /* ATMEL_BASE_CS6 */
+
+#ifdef CONFIG_SYS_USE_DATAFLASH
 
 /* bootstrap + u-boot + env in dataflash on CS0 */
-#define CONFIG_ENV_IS_IN_DATAFLASH	1
+#define CONFIG_ENV_IS_IN_DATAFLASH
 #define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
 					0x8400)
 #define CONFIG_ENV_OFFSET		0x4200
@@ -165,16 +187,22 @@
 					CONFIG_ENV_OFFSET)
 #define CONFIG_ENV_SIZE			0x4200
 
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_SYS_BAUDRATE_TABLE	{115200 , 19200, 38400, 57600, 9600 }
+#elif CONFIG_SYS_USE_NANDFLASH
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_OFFSET		0xC0000
+#define CONFIG_ENV_SIZE			0x20000
+
+#endif
 
 #define CONFIG_SYS_PROMPT		"=> "
-#define CONFIG_SYS_CBSIZE		256
+#define CONFIG_SYS_CBSIZE		512
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP		1
-#define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
 
 /*
  * Size of malloc() pool
diff --git a/include/configs/otc570.h b/include/configs/otc570.h
index ca3bf26..013c837 100644
--- a/include/configs/otc570.h
+++ b/include/configs/otc570.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2010
+ * (C) Copyright 2010-2011
  * Daniel Gorsulowski <daniel.gorsulowski at esd.eu>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -31,72 +31,90 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/* Common stuff */
-#define CONFIG_OTC570			1	/* Board is esd OTC570 */
-#define CONFIG_ARM926EJS		1	/* This is an ARM926EJS Core */
-#define CONFIG_AT91SAM9263		1	/* It's an AT91SAM9263 SoC */
-#define CONFIG_SYS_AT91_MAIN_CLOCK	16000000/* 16.0 MHz crystal */
-#define CONFIG_SYS_HZ			1000	/* decrementer freq */
-#define CONFIG_DISPLAY_BOARDINFO	1
-#define CONFIG_DISPLAY_CPUINFO		1	/* display cpu info and speed */
-#define CONFIG_PREBOOT				/* enable preboot variable */
-#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-#define CONFIG_SERIAL_TAG		1
-#define CONFIG_REVISION_TAG		1
-#undef CONFIG_USE_IRQ				/* don't need IRQ/FIQ stuff */
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
 
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_MISC_INIT_R		1	/* Call misc_init_r */
+/*
+ * Warning: changing CONFIG_SYS_TEXT_BASE requires
+ * adapting the initial boot program.
+ * Since the linker has to swallow that define, we must use a pure
+ * hex number here!
+ */
+#define CONFIG_SYS_TEXT_BASE		0x23f00000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768	/* slow clock xtal */
+#define CONFIG_SYS_AT91_MAIN_CLOCK	16000000/* main clock xtal */
+#define CONFIG_SYS_HZ			1000	/* decrementer freq */
 
+/* Misc CPU related */
+#undef	CONFIG_USE_IRQ				/* don't need IRQ/FIQ stuff */
+#define CONFIG_OTC570				/* Board is esd OTC570 */
+#define CONFIG_MISC_INIT_R			/* Call misc_init_r */
+#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
+#define CONFIG_PREBOOT				/* enable preboot variable */
+#define CONFIG_DISPLAY_CPUINFO			/* display cpu info and speed */
+#define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_ARCH_CPU_INIT
+#define CONFIG_SERIAL_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SKIP_LOWLEVEL_INIT
 
 /*
  * Hardware drivers
  */
-#define CONFIG_AT91_GPIO		1
+
+/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is reworked */
+#define ATMEL_PMC_UHP			AT91SAM926x_PMC_UHP
+
+/* general purpose I/O */
+#define CONFIG_AT91_GPIO
 
 /* Console output */
-#define CONFIG_ATMEL_USART		1
-#undef CONFIG_USART0
-#undef CONFIG_USART1
-#undef CONFIG_USART2
-#define CONFIG_USART3			1	/* USART 3 is DBGU */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define CONFIG_USART_ID			ATMEL_ID_SYS
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{115200, 19200, 38400, 57600, 9600}
 
 #define CONFIG_BOOTDELAY		3
-#define CONFIG_ZERO_BOOTDELAY_CHECK	1
+#define CONFIG_ZERO_BOOTDELAY_CHECK
 
 /* LCD */
-#define CONFIG_LCD			1
+#define CONFIG_LCD
 #define LCD_BPP				LCD_COLOR8
 
 #undef CONFIG_SPLASH_SCREEN
 
 #ifndef CONFIG_SPLASH_SCREEN
-#define CONFIG_LCD_LOGO			1
-#define CONFIG_LCD_INFO			1
+#define CONFIG_LCD_LOGO
+#define CONFIG_LCD_INFO
 #undef CONFIG_LCD_INFO_BELOW_LOGO
 #endif /* CONFIG_SPLASH_SCREEN */
 
 #undef LCD_TEST_PATTERN
-#define CONFIG_SYS_WHITE_ON_BLACK	1
-#define CONFIG_ATMEL_LCD		1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_ATMEL_LCD
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
 #define CONFIG_OTC570_LCD_BASE		0x23E00000	/* LCD is in SDRAM */
-#define CONFIG_CMD_BMP			1
+#define CONFIG_CMD_BMP
 
 /* RTC and I2C stuff */
-#define CONFIG_RTC_DS1338		1
+#define CONFIG_RTC_DS1338
 #define CONFIG_SYS_I2C_RTC_ADDR		0x68
 #undef CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C			1
+#define CONFIG_SOFT_I2C
 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
 #ifdef CONFIG_SOFT_I2C
-#define CONFIG_I2C_CMD_TREE		1
-#define CONFIG_I2C_MULTI_BUS		1
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_I2C_MULTI_BUS
 /* Configure data and clock pins for pio */
 #define I2C_INIT { \
 	at91_set_pio_output(AT91_PIO_PORTB, 4, 0); \
@@ -116,16 +134,13 @@
 #define I2C_DELAY		udelay(2) /* 1/4 I2C clock duration */
 #endif /* CONFIG_SOFT_I2C */
 
-#define CONFIG_BOOTDELAY		3
-#define CONFIG_ZERO_BOOTDELAY_CHECK	1
-
 /*
  * BOOTP options
  */
-#define CONFIG_BOOTP_BOOTFILESIZE	1
-#define CONFIG_BOOTP_BOOTPATH		1
-#define CONFIG_BOOTP_GATEWAY		1
-#define CONFIG_BOOTP_HOSTNAME		1
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
 
 /*
  * Command line configuration.
@@ -135,23 +150,27 @@
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_IMLS
 
-#define CONFIG_CMD_PING			1
-#define CONFIG_CMD_DHCP			1
-#define CONFIG_CMD_NAND			1
-#define CONFIG_CMD_USB			1
-#define CONFIG_CMD_I2C			1
-#define CONFIG_CMD_DATE			1
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DATE
 
 /* LED */
-#define CONFIG_AT91_LED			1
+#define CONFIG_AT91_LED
 
 /* SDRAM */
-#define CONFIG_NR_DRAM_BANKS			1
-#define PHYS_SDRAM				0x20000000
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		0x20000000
+
+/* Initial stack pointer */
+#define CONFIG_SYS_INIT_SP_ADDR	\
+	(CONFIG_SYS_TEXT_BASE - GENERATED_GBL_DATA_SIZE)
 
 /* DataFlash */
 #define CONFIG_ATMEL_DATAFLASH_SPI
-#define CONFIG_HAS_DATAFLASH			1
+#define CONFIG_HAS_DATAFLASH
 #define CONFIG_SYS_SPI_WRITE_TOUT		(5 * CONFIG_SYS_HZ)
 #define CONFIG_SYS_MAX_DATAFLASH_BANKS		1
 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0	0xC0000000	/* CS0 */
@@ -160,14 +179,14 @@
 #define DATAFLASH_TCHS				(0x1 << 24)
 
 /* NOR flash is not populated, disable it */
-#define CONFIG_SYS_NO_FLASH			1
+#define CONFIG_SYS_NO_FLASH
 
 /* NAND flash */
 #ifdef CONFIG_CMD_NAND
 #define CONFIG_NAND_ATMEL
 #define CONFIG_SYS_MAX_NAND_DEVICE		1
 #define CONFIG_SYS_NAND_BASE			0x40000000
-#define CONFIG_SYS_NAND_DBW_8			1
+#define CONFIG_SYS_NAND_DBW_8
 /* our ALE is AD21 */
 #define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
 /* our CLE is AD22 */
@@ -178,39 +197,39 @@
 #endif
 
 /* Ethernet */
-#define CONFIG_MACB				1
-#define CONFIG_RMII				1
-#define CONFIG_NET_MULTI			1
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_MULTI
+#define CONFIG_FIT
 #define CONFIG_NET_RETRY_COUNT			20
 #undef CONFIG_RESET_PHY_R
 
 /* USB */
 #define CONFIG_USB_ATMEL
-#define CONFIG_USB_OHCI_NEW			1
-#define CONFIG_DOS_PARTITION			1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT		1
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
 #define CONFIG_SYS_USB_OHCI_REGS_BASE		0x00a00000
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME		"at91sam9263"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
-#define CONFIG_USB_STORAGE			1
-#define CONFIG_CMD_FAT				1
-
-#define CONFIG_SYS_LOAD_ADDR			0x22000000 /* load address */
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_FAT
 
-#define CONFIG_SYS_MEMTEST_START		PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END			0x23e00000
+#define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */
 
-#define CONFIG_SYS_USE_DATAFLASH		1
-#undef CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		0x23e00000
 
 /* CAN */
-#define CONFIG_AT91_CAN				1
+#define CONFIG_AT91_CAN
 
 /* hw-controller addresses */
-#define CONFIG_ET1100_BASE			0x70000000
+#define CONFIG_ET1100_BASE		0x70000000 /* ATMEL_BASE_CS6 */
+
+#ifdef CONFIG_SYS_USE_DATAFLASH
 
 /* bootstrap + u-boot + env in dataflash on CS0 */
-#define CONFIG_ENV_IS_IN_DATAFLASH	1
+#define CONFIG_ENV_IS_IN_DATAFLASH
 #define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
 					0x8400)
 #define CONFIG_ENV_OFFSET		0x4200
@@ -218,16 +237,22 @@
 					CONFIG_ENV_OFFSET)
 #define CONFIG_ENV_SIZE			0x4200
 
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_SYS_BAUDRATE_TABLE	{115200 , 19200, 38400, 57600, 9600 }
+#elif CONFIG_SYS_USE_NANDFLASH
+
+/* bootstrap + u-boot + env + linux in nandflash */
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_OFFSET		0xC0000
+#define CONFIG_ENV_SIZE			0x20000
+
+#endif
 
 #define CONFIG_SYS_PROMPT		"=> "
-#define CONFIG_SYS_CBSIZE		256
+#define CONFIG_SYS_CBSIZE		512
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP		1
-#define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
 
 /*
  * Size of malloc() pool
-- 
1.5.3



More information about the U-Boot mailing list