[U-Boot] [GIT PULL] Pull request: u-boot-imx

[Stefano Babic]

Hi Albert,

The following changes since commit d6a5e6d531e357dd8016141f73d370d02886a7eb:

  Cleanup .boards.depend when using an objtree (2011-01-21 08:56:50 +0100)

are available in the git repository at:
  git://www.denx.de/git/u-boot-imx.git master

Liu Hui-R64343 (8):
      MX51EVK: UART does not print out the early information
      MX5: Add initial support for MX53 processor
      fec_mxc: add support for MX53 processor
      serial_mxc: add support for MX53 processor
      mxc_gpio: add support for MX53 processor
      mxc_i2c: add support for MX53 processor
      fsl_pmic: add I2C interface support
      MX5:MX53: add initial support for MX53EVK board

Marek Vasut (1):
      BLOCK: Add freescale IMX51 PATA driver

Stefano Babic (1):
      mxc_nand: add support for i.MX35 processor

 MAINTAINERS                                 |    4 +
 arch/arm/cpu/armv7/mx5/iomux.c              |   30 ++-
 arch/arm/cpu/armv7/mx5/lowlevel_init.S      |   91 +++---
 arch/arm/cpu/armv7/mx5/soc.c                |   22 +-
 arch/arm/include/asm/arch-mx5/asm-offsets.h |    5 +
 arch/arm/include/asm/arch-mx5/imx-regs.h    |   82 ++---
 arch/arm/include/asm/arch-mx5/iomux.h       |  102 ------
 arch/arm/include/asm/arch-mx5/mx5x_pins.h   |  469
++++++++++++++++++++++++++-
 board/freescale/mx51evk/mx51evk.c           |   11 +-
 board/freescale/mx53evk/Makefile            |   48 +++
 board/freescale/mx53evk/config.mk           |   24 ++
 board/freescale/mx53evk/imximage.cfg        |  112 +++++++
 board/freescale/mx53evk/mx53evk.c           |  397 +++++++++++++++++++++++
 boards.cfg                                  |    1 +
 drivers/block/Makefile                      |    1 +
 drivers/block/mxc_ata.c                     |  149 +++++++++
 drivers/gpio/mxc_gpio.c                     |    9 +-
 drivers/i2c/mxc_i2c.c                       |   21 +-
 drivers/misc/fsl_pmic.c                     |   45 +++-
 drivers/mtd/nand/mxc_nand.c                 |    6 +-
 drivers/net/fec_mxc.c                       |    2 +-
 drivers/net/fec_mxc.h                       |    4 +-
 drivers/serial/serial_mxc.c                 |    6 +
 include/configs/mx51evk.h                   |    5 +-
 include/configs/mx53evk.h                   |  193 +++++++++++
 include/configs/vision2.h                   |    3 +-
 include/mc13892.h                           |    5 +
 27 files changed, 1620 insertions(+), 227 deletions(-)
 mode change 100644 => 100755 arch/arm/cpu/armv7/mx5/iomux.c
 mode change 100644 => 100755 arch/arm/cpu/armv7/mx5/lowlevel_init.S
 mode change 100644 => 100755 arch/arm/include/asm/arch-mx5/imx-regs.h
 mode change 100644 => 100755 arch/arm/include/asm/arch-mx5/mx5x_pins.h
 create mode 100755 board/freescale/mx53evk/Makefile
 create mode 100755 board/freescale/mx53evk/config.mk
 create mode 100644 board/freescale/mx53evk/imximage.cfg
 create mode 100755 board/freescale/mx53evk/mx53evk.c
 create mode 100644 drivers/block/mxc_ata.c
 mode change 100644 => 100755 drivers/i2c/mxc_i2c.c
 mode change 100644 => 100755 include/configs/mx51evk.h
 create mode 100755 include/configs/mx53evk.h


-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================