[U-Boot] [PATCH v2 2/2] net: sh_eth: add cache handling

[Yoshihiro Shimoda]

Some CPU needs cache handling. So this patch add the config of
CONFIG_SH_ETHER_CACHE_WRITEBACK, and it calls wback function.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh at renesas.com>
---
 about v2:
  - add description of new configuration to README
  (This patch depends on "README: add description of sh_eth driver")

 README               |    3 +++
 drivers/net/sh_eth.c |    9 +++++++++
 2 files changed, 12 insertions(+), 0 deletions(-)

diff --git a/README b/README
index 41458a3..7de9b14 100644
--- a/README
+++ b/README
@@ -897,6 +897,9 @@ The following options need to be configured:
 			CONFIG_SH_ETHER_PHY_ADDR
 			Define the ETH PHY's address

+			CONFIG_SH_ETHER_CACHE_WRITEBACK
+			If this option is set, the driver enables cache flush.
+
 - USB Support:
 		At the moment only the UHCI host controller is
 		supported (PIP405, MIP405, MPC5200); define
diff --git a/drivers/net/sh_eth.c b/drivers/net/sh_eth.c
index 86cc324..53d918d 100644
--- a/drivers/net/sh_eth.c
+++ b/drivers/net/sh_eth.c
@@ -36,6 +36,12 @@
 #ifndef CONFIG_SH_ETHER_PHY_ADDR
 # error "Please define CONFIG_SH_ETHER_PHY_ADDR"
 #endif
+#ifdef CONFIG_SH_ETHER_CACHE_WRITEBACK
+#define flush_cache_wback(addr, len)	\
+			dcache_wback_range((u32)addr, (u32)(addr + len - 1))
+#else
+#define flush_cache_wback(...)
+#endif

 #define SH_ETH_PHY_DELAY 50000

@@ -197,6 +203,7 @@ int sh_eth_send(struct eth_device *dev, volatile void *packet, int len)
 	}

 	/* Update tx descriptor */
+	flush_cache_wback(packet, len);
 	port_info->tx_desc_cur->td2 = ADDR_TO_PHY(packet);
 	port_info->tx_desc_cur->td1 = len << 16;
 	/* Must preserve the end of descriptor list indication */
@@ -312,6 +319,7 @@ static int sh_eth_tx_desc_init(struct sh_eth_dev *eth)

 	tmp_addr = (u32) (((int)port_info->tx_desc_malloc + TX_DESC_SIZE - 1) &
 			  ~(TX_DESC_SIZE - 1));
+	flush_cache_wback(tmp_addr, NUM_TX_DESC * sizeof(struct tx_desc_s));
 	/* Make sure we use a P2 address (non-cacheable) */
 	port_info->tx_desc_base = (struct tx_desc_s *)ADDR_TO_P2(tmp_addr);
 	port_info->tx_desc_cur = port_info->tx_desc_base;
@@ -361,6 +369,7 @@ static int sh_eth_rx_desc_init(struct sh_eth_dev *eth)

 	tmp_addr = (u32) (((int)port_info->rx_desc_malloc + RX_DESC_SIZE - 1) &
 			  ~(RX_DESC_SIZE - 1));
+	flush_cache_wback(tmp_addr, NUM_RX_DESC * sizeof(struct rx_desc_s));
 	/* Make sure we use a P2 address (non-cacheable) */
 	port_info->rx_desc_base = (struct rx_desc_s *)ADDR_TO_P2(tmp_addr);

-- 
1.7.1