[U-Boot] [PATCH 9/9] arm, davinci: add cam_enc_4xx support
Heiko Schocher
hs at denx.de
Sat Jul 16 12:06:50 CEST 2011
- DM368 SOC
- booting with nand_spl not with UBL from TI
- before loading u-boot from NAND into RAM, test
the RAM with the post memory test. If error
is found, switch all LEDs on and halt system.
- SPI Flash
Dataflash Typ: M25PE80
- Ethernet DM9161BI
Signed-off-by: Heiko Schocher <hs at denx.de>
---
MAINTAINERS | 1 +
MAKEALL | 1 +
board/ait/cam_enc_4xx/Makefile | 52 ++++
board/ait/cam_enc_4xx/cam_enc_4xx.c | 331 ++++++++++++++++++++
board/ait/cam_enc_4xx/cam_enc_4xx_nand_spl.c | 115 +++++++
board/ait/cam_enc_4xx/config.mk | 19 ++
board/ait/cam_enc_4xx/ublimage.cfg | 48 +++
boards.cfg | 1 +
doc/README.davinci.nand_spl | 141 +++++++++
include/configs/cam_enc_4xx.h | 423 ++++++++++++++++++++++++++
nand_spl/board/ait/cam_enc_4xx/Makefile | 152 +++++++++
nand_spl/board/ait/cam_enc_4xx/u-boot.lds | 75 +++++
12 files changed, 1359 insertions(+), 0 deletions(-)
create mode 100644 board/ait/cam_enc_4xx/Makefile
create mode 100644 board/ait/cam_enc_4xx/cam_enc_4xx.c
create mode 100644 board/ait/cam_enc_4xx/cam_enc_4xx_nand_spl.c
create mode 100644 board/ait/cam_enc_4xx/config.mk
create mode 100644 board/ait/cam_enc_4xx/ublimage.cfg
create mode 100644 doc/README.davinci.nand_spl
create mode 100644 include/configs/cam_enc_4xx.h
create mode 100644 nand_spl/board/ait/cam_enc_4xx/Makefile
create mode 100644 nand_spl/board/ait/cam_enc_4xx/u-boot.lds
diff --git a/MAINTAINERS b/MAINTAINERS
index 143f31b..3ef515d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -428,6 +428,7 @@ Georg Schardt <schardt at team-ctech.de>
Heiko Schocher <hs at denx.de>
+ cam_enc_4xx davinci/ARM926EJS
charon MPC5200
ids8247 MPC8247
jupiter MPC5200
diff --git a/MAKEALL b/MAKEALL
index 4adaeb8..70c8f84 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -328,6 +328,7 @@ LIST_ARM9=" \
ap946es \
ap966 \
aspenite \
+ cam_enc_4xx \
cp920t \
cp922_XA10 \
cp926ejs \
diff --git a/board/ait/cam_enc_4xx/Makefile b/board/ait/cam_enc_4xx/Makefile
new file mode 100644
index 0000000..4804597
--- /dev/null
+++ b/board/ait/cam_enc_4xx/Makefile
@@ -0,0 +1,52 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := $(BOARD).o
+SOBJS :=
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+# This is for $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ait/cam_enc_4xx/cam_enc_4xx.c b/board/ait/cam_enc_4xx/cam_enc_4xx.c
new file mode 100644
index 0000000..f44196f
--- /dev/null
+++ b/board/ait/cam_enc_4xx/cam_enc_4xx.c
@@ -0,0 +1,331 @@
+/*
+ * Copyright (C) 2009 Texas Instruments Incorporated
+ *
+ * Copyright (C) 2011
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <common.h>
+#include <linux/mtd/nand.h>
+#include <nand.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/emif_defs.h>
+#include <asm/arch/nand_defs.h>
+#include <asm/arch/gpio_defs.h>
+#include <asm/arch/syscfg_defs.h>
+#include <asm/arch/davinci_misc.h>
+#ifdef CONFIG_DAVINCI_MMC
+#include <mmc.h>
+#include <asm/arch/sdmmc_defs.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_PRELOADER
+int dram_init(void)
+{
+ /* dram_init must store complete ramsize in gd->ram_size */
+ gd->ram_size = get_ram_size(
+ (void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_MAX_RAM_BANK_SIZE);
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_dram[0].size = gd->ram_size;
+}
+
+int checkboard(void)
+{
+ printf("Board: AIT CAM ENC 4XX\n");
+ return 0;
+}
+
+int board_init(void)
+{
+ gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DM365_EVM;
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+int board_eth_init(bd_t *bis)
+{
+ davinci_emac_initialize();
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_NAND_DAVINCI
+static int
+davinci_std_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int page)
+{
+ struct nand_chip *this = mtd->priv;
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *oob = chip->oob_poi;
+
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0x0, page & this->pagemask);
+
+ chip->read_buf(mtd, oob, mtd->oobsize);
+
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, page & this->pagemask);
+
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ chip->ecc.hwctl(mtd, NAND_ECC_READ);
+ chip->read_buf(mtd, p, eccsize);
+ chip->ecc.hwctl(mtd, NAND_ECC_READSYN);
+
+ if (chip->ecc.prepad)
+ oob += chip->ecc.prepad;
+
+ stat = chip->ecc.correct(mtd, p, oob, NULL);
+
+ if (stat == -1)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += stat;
+
+ oob += eccbytes;
+
+ if (chip->ecc.postpad)
+ oob += chip->ecc.postpad;
+ }
+
+ /* Calculate remaining oob bytes */
+ i = mtd->oobsize - (oob - chip->oob_poi);
+ if (i)
+ chip->read_buf(mtd, oob, i);
+
+ return 0;
+}
+
+static void davinci_std_write_page_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf)
+{
+ unsigned char davinci_ecc_buf[NAND_MAX_OOBSIZE];
+ struct nand_chip *this = mtd->priv;
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad;
+ int offset = 0;
+ const uint8_t *p = buf;
+ uint8_t *oob = chip->oob_poi;
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
+ chip->write_buf(mtd, p, eccsize);
+
+ /* Calculate ECC without prepad */
+ chip->ecc.calculate(mtd, p, oob + chip->ecc.prepad);
+
+ if (chip->ecc.prepad) {
+ offset = ((chip->ecc.steps - eccsteps) * chunk);
+ memcpy(&davinci_ecc_buf[offset], oob, chip->ecc.prepad);
+ oob += chip->ecc.prepad;
+ }
+
+ offset = (((chip->ecc.steps - eccsteps) * chunk) +
+ chip->ecc.prepad);
+ memcpy(&davinci_ecc_buf[offset], oob, eccbytes);
+ oob += eccbytes;
+
+ if (chip->ecc.postpad) {
+ offset = (((chip->ecc.steps - eccsteps) * chunk) +
+ (chip->ecc.prepad + eccbytes));
+ memcpy(&davinci_ecc_buf[offset], oob,
+ chip->ecc.postpad);
+ oob += chip->ecc.postpad;
+ }
+ }
+
+ /*
+ * Write the sparebytes into the page once
+ * all eccsteps have been covered
+ */
+ for (i = 0; i < mtd->oobsize; i++)
+ writeb(davinci_ecc_buf[i], this->IO_ADDR_W);
+
+ /* Calculate remaining oob bytes */
+ i = mtd->oobsize - (oob - chip->oob_poi);
+ if (i)
+ chip->write_buf(mtd, oob, i);
+}
+
+static int davinci_std_write_oob_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ int pos, status = 0;
+ const uint8_t *bufpoi = chip->oob_poi;
+
+ pos = mtd->writesize;
+
+ chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page);
+
+ chip->write_buf(mtd, bufpoi, mtd->oobsize);
+
+ chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+ status = chip->waitfunc(mtd, chip);
+
+ return status & NAND_STATUS_FAIL ? -1 : 0;
+}
+
+static int davinci_std_read_oob_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip, int page, int sndcmd)
+{
+ struct nand_chip *this = mtd->priv;
+ uint8_t *buf = chip->oob_poi;
+ uint8_t *bufpoi = buf;
+
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0x0, page & this->pagemask);
+
+ chip->read_buf(mtd, bufpoi, mtd->oobsize);
+
+ return 1;
+}
+
+static void nand_dm365evm_select_chip(struct mtd_info *mtd, int chip)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long wbase = (unsigned long) this->IO_ADDR_W;
+ unsigned long rbase = (unsigned long) this->IO_ADDR_R;
+
+ if (chip == 1) {
+ __set_bit(14, &wbase);
+ __set_bit(14, &rbase);
+ } else {
+ __clear_bit(14, &wbase);
+ __clear_bit(14, &rbase);
+ }
+ this->IO_ADDR_W = (void *)wbase;
+ this->IO_ADDR_R = (void *)rbase;
+}
+
+int board_nand_init(struct nand_chip *nand)
+{
+ davinci_nand_init(nand);
+ nand->select_chip = nand_dm365evm_select_chip;
+
+ return 0;
+}
+
+#ifdef CONFIG_CMD_NAND_HWFUNC
+struct nand_ecc_ctrl org_ecc;
+static int notsaved = 1;
+
+static int nand_switch_hw_func(int mode)
+{
+ struct nand_chip *nand;
+ struct mtd_info *mtd;
+
+ if (nand_curr_device < 0 ||
+ nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE ||
+ !nand_info[nand_curr_device].name) {
+ printf("Error: Can't switch hw functions," \
+ " no devices available\n");
+ return -1;
+ }
+
+ mtd = &nand_info[nand_curr_device];
+ nand = mtd->priv;
+
+ if (mode == 0) {
+ printf("switching to uboot hw functions.\n");
+ memcpy(&nand->ecc, &org_ecc, sizeof(struct nand_ecc_ctrl));
+ } else {
+ /* RBL */
+ printf("switching to RBL hw functions.\n");
+ if (notsaved == 1) {
+ memcpy(&org_ecc, &nand->ecc,
+ sizeof(struct nand_ecc_ctrl));
+ notsaved = 0;
+ }
+ nand->ecc.mode = NAND_ECC_HW_SYNDROME;
+ nand->ecc.prepad = 6;
+ nand->ecc.read_page = davinci_std_read_page_syndrome;
+ nand->ecc.write_page = davinci_std_write_page_syndrome;
+ nand->ecc.read_oob = davinci_std_read_oob_syndrome;
+ nand->ecc.write_oob = davinci_std_write_oob_syndrome;
+ }
+ return mode;
+}
+
+static int hwmode;
+
+int nand_hwfunc(int argc, char * const argv[])
+{
+ int newmode;
+
+ if (argc == 0) {
+ printf("%s\n", hwmode ? "rbl" : "uboot");
+ return 0;
+ }
+
+ if (strncmp(argv[0], "rbl", 2) == 0)
+ newmode = 1;
+ else if (strncmp(argv[0], "uboot", 2) == 0)
+ newmode = 0;
+ else
+ goto usage;
+
+ if (hwmode == newmode)
+ return 0;
+
+ hwmode = nand_switch_hw_func(newmode);
+
+ return 0;
+
+usage:
+ printf("Usage: nandhwfunc rbl/uboot\n");
+ return 1;
+}
+#endif
+#endif
+
+#ifdef CONFIG_DAVINCI_MMC
+static struct davinci_mmc mmc_sd0 = {
+ .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
+ .input_clk = 121500000,
+ .host_caps = MMC_MODE_4BIT,
+ .voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .version = MMC_CTLR_VERSION_2,
+};
+
+int board_mmc_init(bd_t *bis)
+{
+ int err;
+
+ /* Add slot-0 to mmc subsystem */
+ err = davinci_mmc_init(bis, &mmc_sd0);
+
+ return err;
+}
+#endif
diff --git a/board/ait/cam_enc_4xx/cam_enc_4xx_nand_spl.c b/board/ait/cam_enc_4xx/cam_enc_4xx_nand_spl.c
new file mode 100644
index 0000000..cc07f47
--- /dev/null
+++ b/board/ait/cam_enc_4xx/cam_enc_4xx_nand_spl.c
@@ -0,0 +1,115 @@
+/*
+ *
+ * Copyright (C) 2011
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <nsekhar at ti.com>
+ * Copyright (C) 2007 Sergey Kubushyn <ksi at koi8.net>
+ * Copyright (C) 2004 Texas Instruments.
+ *
+ * ----------------------------------------------------------------------------
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ * ----------------------------------------------------------------------------
+ */
+#include <common.h>
+#include <asm/errno.h>
+#include <asm/arch/hardware.h>
+#include <asm/io.h>
+#include <asm/arch/davinci_misc.h>
+#include <ns16550.h>
+#include <post.h>
+#include <nand.h>
+#include <asm/arch/dm365_lowlevel.h>
+
+static void cam_enc_4xx_set_all_led(void)
+{
+ struct davinci_gpio *gpio = davinci_gpio_bank01;
+
+ setbits_le32(&gpio->out_data, 0x02000000);
+ gpio = davinci_gpio_bank45;
+ setbits_le32(&gpio->out_data, 0x04c00000);
+}
+
+void board_gpio_init(void)
+{
+ struct davinci_gpio *gpio;
+
+ gpio = davinci_gpio_bank01;
+ clrbits_le32(&gpio->dir, ~0xfdfffffe);
+ /* clear LED D14 = GPIO25 */
+ clrbits_le32(&gpio->out_data, 0x02000000);
+ gpio = davinci_gpio_bank23;
+ clrbits_le32(&gpio->dir, ~0x5ff0afef);
+ /*
+ * PHY out of reset GIO 50 = 1
+ * NAND WP off GIO 51 = 1
+ */
+ setbits_le32(&gpio->out_data, 0x000c0004);
+ gpio = davinci_gpio_bank45;
+ clrbits_le32(&gpio->dir, ~0xdb2fffff);
+ /*
+ * clear LED:
+ * D17 = GPIO86
+ * D11 = GPIO87
+ * D13 = GPIO90
+ */
+ clrbits_le32(&gpio->out_data, 0x04c00000);
+ gpio = davinci_gpio_bank67;
+ clrbits_le32(&gpio->dir, ~0x000007ff);
+}
+
+void puts(const char *str)
+{
+ while (*str)
+ putc(*str++);
+}
+
+void putc(char c)
+{
+ if (c == '\n')
+ NS16550_putc((NS16550_t)(CONFIG_SYS_NS16550_COM1), '\r');
+
+ NS16550_putc((NS16550_t)(CONFIG_SYS_NS16550_COM1), c);
+}
+
+void hang(void)
+{
+ puts("### ERROR ### Please RESET the board ###\n");
+ for (;;)
+ ;
+}
+
+/*
+ * functions for the post memory test.
+ */
+int arch_memory_test_prepare(u32 *vstart, u32 *size, phys_addr_t *phys_offset)
+{
+ *vstart = CONFIG_SYS_SDRAM_BASE;
+ *size = PHYS_SDRAM_1_SIZE;
+ *phys_offset = 0;
+ return 0;
+}
+
+void arch_memory_failure_handle(void)
+{
+ cam_enc_4xx_set_all_led();
+ puts("mem failure\n");
+ return;
+}
+
+int post_log(char *format, ...)
+{
+ return 0;
+}
diff --git a/board/ait/cam_enc_4xx/config.mk b/board/ait/cam_enc_4xx/config.mk
new file mode 100644
index 0000000..1169325
--- /dev/null
+++ b/board/ait/cam_enc_4xx/config.mk
@@ -0,0 +1,19 @@
+#
+# AIT cam_enc_4xx board
+# cam_enc_4xx board has 1 bank of 256 MB DDR RAM
+# Physical Address: 8000'0000 to 9000'0000
+#
+# Linux Kernel is expected to be at 8000'8000, entry 8000'8000
+# (mem base + reserved)
+#
+
+#Provide at least 16MB spacing between us and the Linux Kernel image
+ifdef CONFIG_NAND_SPL
+#TEXT_BASE + (6 * pagesize)
+PAD_TO := 12320
+CONFIG_SYS_TEXT_BASE = 0x0000020
+else
+UBL_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/ublimage.cfg
+CONFIG_SYS_TEXT_BASE = 0x81080000
+ALL += $(obj)u-boot.ubl
+endif
diff --git a/board/ait/cam_enc_4xx/ublimage.cfg b/board/ait/cam_enc_4xx/ublimage.cfg
new file mode 100644
index 0000000..5f17de1
--- /dev/null
+++ b/board/ait/cam_enc_4xx/ublimage.cfg
@@ -0,0 +1,48 @@
+#
+# (C Copyright 2011
+# Heiko Schocher DENX Software Engineering hs at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not write to the Free Software
+# Foundation Inc. 51 Franklin Street Fifth Floor Boston,
+# MA 02110-1301 USA
+#
+# Refer doc/README.ublimage for more details about how-to configure
+# and create ublimage boot image
+#
+# The syntax is taken as close as possible with the kwbimage
+
+# UBL special mode : one of
+# safe (the board has no nand neither onenand)
+MODE safe
+
+# Entry point address for the user bootloader (absolute address)
+# nand_spl TEXT_BASE = 0x20 !!
+ENTRY 0x00000020
+
+# Number of pages (size of user bootloader in number of pages)
+# @ nand_spl 6 pages
+PAGES 6
+
+# Block number where user bootloader is present
+# RBL starts always with block 1
+START_BLOCK 5
+
+# Page number where user bootloader is present
+# Page 0 is always UBL header
+START_PAGE 0
+
+LD_ADDR 0x20
diff --git a/boards.cfg b/boards.cfg
index 4522ea7..c376091 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -103,6 +103,7 @@ pm9261 arm arm926ejs - ronetix
pm9263 arm arm926ejs - ronetix at91
da830evm arm arm926ejs da8xxevm davinci davinci
da850evm arm arm926ejs da8xxevm davinci davinci
+cam_enc_4xx arm arm926ejs cam_enc_4xx ait davinci cam_enc_4xx:NAND_U_BOOT
hawkboard arm arm926ejs da8xxevm davinci davinci
hawkboard_nand arm arm926ejs da8xxevm davinci davinci hawkboard:NAND_U_BOOT
hawkboard_uart arm arm926ejs da8xxevm davinci davinci hawkboard:UART_U_BOOT
diff --git a/doc/README.davinci.nand_spl b/doc/README.davinci.nand_spl
new file mode 100644
index 0000000..51bb624
--- /dev/null
+++ b/doc/README.davinci.nand_spl
@@ -0,0 +1,141 @@
+With this approach, we don't need the UBL any more on DaVinci boards.
+A "make boardname" will compile a u-boot.ubl, with UBL Header, which is
+needed for the RBL to find the "UBL", which actually is a UBL-compatible
+header, nand_spl code and u-boot code.
+
+
+As the RBL uses another read function as the "standard" u-boot,
+we need a command, which switches between this two read/write
+functions, so we can write the UBL header and the nand_spl
+code in a format, which the RBL can read. This is realize
+(at the moment in board specific code) in the u-boot command
+nand hwfunc.
+
+nand hwfunc without arguments returns actual mode (rbl or uboot).
+with nand hwfunc mode (mode = "rbl" or "uboot") you can switch
+between the two NAND read/write modes.
+
+
+To set up mkimage you need a config file for mkimage, example:
+board/davinci/ait/ublimage.cfg
+
+For information about the configuration please see:
+doc/README.ublimage
+
+Example for the cam_enc_4xx board:
+On the cam_enc_4xx board we have a NAND flash with blocksize = 0x20000 and
+pagesize = 0x800, so the u-boot.ubl image (which you get with:
+"make cam_enc_4xx") looks like this:
+
+00000000 00 ed ac a1 20 00 00 00 06 00 00 00 05 00 00 00 |.... ...........|
+00000010 00 00 00 00 20 00 00 00 ff ff ff ff ff ff ff ff |.... ...........|
+00000020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
+*
+00000800 14 00 00 ea 14 f0 9f e5 10 f0 9f e5 0c f0 9f e5 |................|
+00000810 08 f0 9f e5 04 f0 9f e5 00 f0 9f e5 04 f0 1f e5 |................|
+00000820 00 01 00 00 78 56 34 12 78 56 34 12 78 56 34 12 |....xV4.xV4.xV4.|
+[...]
+*
+00001fe0 00 00 00 00 00 00 00 00 ff ff ff ff ff ff ff ff |................|
+00001ff0 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
+*
+00003800 14 00 00 ea 14 f0 9f e5 14 f0 9f e5 14 f0 9f e5 |................|
+00003810 14 f0 9f e5 14 f0 9f e5 14 f0 9f e5 14 f0 9f e5 |................|
+00003820 80 01 08 81 e0 01 08 81 40 02 08 81 a0 02 08 81 |........ at .......|
+
+In the first "page" of the image, we have the UBL Header, needed for
+the RBL to find the nand_spl code.
+
+The nand_spl code starts in the second "page" of the image, with a size
+defined by:
+
+#define CONFIG_SYS_NROF_PAGES_NAND_SPL 6
+
+After the nand_spl code, there comes the "real" u-boot code
+@ (6 + 1) * pagesize = 0x3800
+
+------------------------------------------------------------------------
+Setting up nand_spl code:
+
+/*
+ * RBL searches from Block n (n = 1..24)
+ * so we can define, how many UBL Headers
+ * we write before the real nand_spl code
+ */
+#define CONFIG_SYS_NROF_UBL_HEADER 5
+#define CONFIG_SYS_NROF_PAGES_NAND_SPL 6
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS ((CONFIG_SYS_NROF_UBL_HEADER * \
+ CONFIG_SYS_NAND_BLOCK_SIZE) + \
+ (CONFIG_SYS_NROF_PAGES_NAND_SPL) * \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+------------------------------------------------------------------------
+
+Burning into NAND:
+
+step 1:
+The RBL searches from Block n ( n = 1..24) on page 0 for valid UBL
+Headers, so you have to burn the UBL header page from the u-boot.ubl
+image to the blocks, you want to have the UBL header.
+!! Don;t forget to switch to rbl nand read/write functions with
+ "nand hwfunc rbl"
+
+step 2:
+You need to setup in the ublimage.cfg, where the RBL can find the nand_spl
+code, and how big it is.
+
+!! RBL always starts reading from page 0 !!
+
+For the AIT board, we have:
+PAGES 6
+START_BLOCK 5
+
+So we need to copy the nand_spl code to block 5 page 0
+!! Don;t forget to switch to rbl nand read/write functions with
+ "nand hwfunc rbl"
+
+step 3:
+You need to copy the u-boot image to the block/page
+where the nand_spl code reads it (CONFIG_SYS_NAND_U_BOOT_OFFS)
+!! Don;t forget to switch to rbl nand read/write functions with
+ "nand hwfunc uboot", which is default.
+
+On the cam_enc_4xx board it is:
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (0xc0000)
+
+-> this results in following NAND usage on the cam_enc_4xx board:
+
+addr
+
+20000 possible UBL Header
+40000 possible UBL Header
+60000 possible UBL Header
+80000 possilbe UBL Header
+a0000 nand_spl code
+c0000 u-boot code
+
+The above steps are executeed through the following environment vars:
+(using 80000 as address for the UBL header)
+
+pagesz=800
+uboot=/tftpboot/cam_enc_4xx/u-boot.ubl
+load=tftp 80000000 ${uboot}
+writeheader nand hwfunc rbl;nand erase 80000 ${pagesz};nand write 80000000 80000 ${pagesz};nand hwfunc uboot
+writenand_spl nand hwfunc rbl;nand erase a0000 3000;nand write 80000800 a0000 3000;nand hwfunc uboot
+writeuboot nand hwfunc uboot;nand erase c0000 5d000;nand write 80003800 c0000 5d000
+update=run load writeheader writenand_spl writeuboot
+
+If you do a "run load update" u-boot, nand_spl + ubl header
+are magically updated ;-)
+
+Note:
+- There seem to be a bug in the RBL code (at least on my HW),
+ In the UBL block, I can set the page to values != 0, so it
+ is possible to burn step 1 and step 2 in one step into the
+ flash, but the RBL ignores the page settings, so I have to
+ burn the UBL Header to a page 0 and the nand_spl code to
+ a page 0 ... :-(
+- If we make the nand read/write functions in the RBL equal to
+ the functions in u-boot (as I have no RBL code, it is only
+ possible in u-boot), we could burn the complete image in
+ one step ... that would be nice ...
diff --git a/include/configs/cam_enc_4xx.h b/include/configs/cam_enc_4xx.h
new file mode 100644
index 0000000..ed2ace9
--- /dev/null
+++ b/include/configs/cam_enc_4xx.h
@@ -0,0 +1,423 @@
+/*
+ * Copyright (C) 2009 Texas Instruments Incorporated
+ *
+ * Copyright (C) 2011
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+
+/* SoC Configuration */
+#define CONFIG_ARM926EJS /* arm926ejs CPU */
+#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
+#define CONFIG_SYS_HZ_CLOCK 24000000 /* timer0 freq */
+#define CONFIG_SYS_HZ 1000
+#define CONFIG_SOC_DM365
+
+#define CONFIG_HOSTNAME cam_enc_4xx
+
+/* Memory Info */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 0x80000000
+#define PHYS_SDRAM_1_SIZE (256 << 20) /* 256 MiB */
+#define DDR_4BANKS /* 4-bank DDR2 (256MB) */
+#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+/* Serial Driver info: UART0 for console */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE -4
+#define CONFIG_SYS_NS16550_COM1 0x01c20000
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* Network Configuration */
+#define CONFIG_DRIVER_TI_EMAC
+#define CONFIG_EMAC_MDIO_PHY_NUM 0
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_NET_RETRY_COUNT 10
+#define CONFIG_NET_MULTI
+#define CONFIG_CMD_MII
+#define CONFIG_SYS_DCACHE_OFF
+
+/* I2C */
+#define CONFIG_HARD_I2C
+#define CONFIG_DRIVER_DAVINCI_I2C
+#define CONFIG_SYS_I2C_SPEED 400000
+#define CONFIG_SYS_I2C_SLAVE 0x10 /* SMBus host address */
+
+/* NAND: socketed, two chipselects, normally 2 GBytes */
+#define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NAND_CS 2
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+#define CONFIG_SYS_NAND_PAGE_2K
+
+#define CONFIG_SYS_NAND_LARGEPAGE
+#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, }
+/* socket has two chipselects, nCE0 gated by address BIT(14) */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_MAX_CHIPS 2
+#define CONFIG_CMD_NAND_HWFUNC "[rbl/uboot]\n\t switch between rbl/uboot"\
+ " nand read/write functions"
+
+/* SPI support */
+#define CONFIG_SPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_DAVINCI_SPI
+#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE
+#define CONFIG_SYS_SPI_CLK davinci_clk_get(SPI_PLLDIV)
+#define CONFIG_SF_DEFAULT_SPEED 3000000
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_CMD_SF
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DAVINCI_MMC
+#define CONFIG_MMC_MBLOCK
+
+/* U-Boot command configuration */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+
+#ifdef CONFIG_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_MMC
+#endif
+
+#ifdef CONFIG_NAND_DAVINCI
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_UBI
+#define CONFIG_RBTREE
+#endif
+
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+
+/* U-Boot general configuration */
+#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */
+#define CONFIG_BOOTFILE "uImage" /* Boot file name */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE /* Print buffer size */ \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_LONGHELP
+
+#ifdef CONFIG_NAND_DAVINCI
+#define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x0
+#undef CONFIG_ENV_IS_IN_FLASH
+#endif
+
+#if defined(CONFIG_MMC) && !defined(CONFIG_ENV_IS_IN_NAND)
+#define CONFIG_CMD_ENV
+#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
+#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */
+#define CONFIG_ENV_IS_IN_MMC
+#undef CONFIG_ENV_IS_IN_FLASH
+#endif
+
+#define CONFIG_BOOTDELAY 3
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_TIMESTAMP
+
+/* U-Boot memory configuration */
+#define CONFIG_STACKSIZE (256 << 10) /* 256 KiB */
+#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* 1 MiB */
+#define CONFIG_SYS_MEMTEST_START 0x80000000 /* physical address */
+#define CONFIG_SYS_MEMTEST_END 0x81000000 /* test 16MB RAM */
+
+/* Linux interfacing */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_SYS_BARGSIZE 1024 /* bootarg Size */
+#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* kernel address */
+
+#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
+
+#ifdef CONFIG_SYS_NAND_LARGEPAGE
+/* Use same layout for 128K/256K blocks; allow some bad blocks */
+#define PART_BOOT "2m(bootloader)ro,"
+#endif
+
+#define PART_KERNEL "4m(kernel)," /* kernel + initramfs */
+#define PART_REST "-(filesystem)"
+
+#define MTDPARTS_DEFAULT \
+ "mtdparts=davinci_nand.0:" PART_BOOT PART_KERNEL PART_REST
+
+#define CONFIG_SYS_NAND_PAGE_SIZE (0x800)
+#define CONFIG_SYS_NAND_BLOCK_SIZE (0x20000)
+
+#if defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (0x00010000 + 0x7f00)
+#define CONFIG_SYS_NAND_BASE 0x02000000
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
+ CONFIG_SYS_NAND_PAGE_SIZE)
+
+#define CONFIG_SYS_NAND_ECCPOS { \
+ 24, 25, 26, 27, 28, \
+ 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
+ 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
+ 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
+ 59, 60, 61, 62, 63 }
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+#define CONFIG_SYS_NAND_ECCSIZE 0x200
+#define CONFIG_SYS_NAND_ECCBYTES 10
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / \
+ CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_ECCTOTAL (40)
+
+#undef CONFIG_DRIVER_TI_EMAC /* no Ethernet in preloader needed */
+
+/*
+ * RBL searches from Block n (n = 1..24)
+ * so we can define, how many UBL Headers
+ * we can write before the real nand_spl code
+ */
+#define CONFIG_SYS_NROF_UBL_HEADER 5
+#define CONFIG_SYS_NROF_PAGES_NAND_SPL 6
+
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x81080000 /* u-boot TEXT_BASE */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+
+/*
+ * Post tests for memory testing
+ */
+#define CONFIG_POST CONFIG_SYS_POST_MEMORY
+#define _POST_WORD_ADDR 0x0
+
+#else /* #if defined(CONFIG_NAND_SPL) */
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x10000 - GENERATED_GBL_DATA_SIZE)
+#endif /* #if defined(CONFIG_NAND_SPL) */
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0xc0000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x60000
+
+/*
+ * U-Boot is a 3rd stage loader and if booting with nand_spl, cpu setup is
+ * done in board_init_f from c code.
+ */
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/* for UBL header */
+#define CONFIG_SYS_UBL_BLOCK (CONFIG_SYS_NAND_PAGE_SIZE)
+
+#define CONFIG_SYS_DM36x_PLL1_PLLM 0x55
+#define CONFIG_SYS_DM36x_PLL1_PREDIV 0x8005
+#define CONFIG_SYS_DM36x_PLL2_PLLM 0x09
+#define CONFIG_SYS_DM36x_PLL2_PREDIV 0x8000
+#define CONFIG_SYS_DM36x_PERI_CLK_CTRL 0x243F04FC
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV1 0x801b
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV2 0x8001
+/* POST DIV 680/2 = 340Mhz -> MJCP and HDVICP bus interface clock */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV3 0x8001
+/*
+ * POST DIV 680/4 = 170Mhz -> EDMA/Peripheral CFG0(1/2 MJCP/HDVICP bus
+ * interface clk)
+ */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV4 0x8003
+/* POST DIV 680/2 = 340Mhz -> VPSS */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV5 0x8001
+/* POST DIV 680/9 = 75.6 Mhz -> VENC */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV6 0x8008
+/*
+ * POST DIV 680/1 = 680Mhz -> DDRx2(with internal divider of 2, clock boils
+ * down to 340 Mhz)
+ */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV7 0x8000
+/* POST DIV 680/7= 97Mhz-> MMC0/SD0 */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV8 0x8006
+/* POST DIV 680/28 = 24.3Mhz-> CLKOUT */
+#define CONFIG_SYS_DM36x_PLL1_PLLDIV9 0x801b
+
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV1 0x8011
+/* POST DIV 432/1=432 Mhz -> ARM926/(HDVICP block) clk */
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV2 0x8000
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV3 0x8001
+/* POST DIV 432/21= 20.5714 Mhz->VOICE Codec clk */
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV4 0x8014
+/* POST DIV 432/16=27 Mhz -> VENC(For SD modes, requires) */
+#define CONFIG_SYS_DM36x_PLL2_PLLDIV5 0x800f
+
+/*
+ * READ LATENCY 7 (CL + 2)
+ * CONFIG_PWRDNEN = 1
+ * CONFIG_EXT_STRBEN = 1
+ */
+#define CONFIG_SYS_DM36x_DDR2_DDRPHYCR (0 \
+ | DM36x_DDR_PHY_EXT_STRBEN \
+ | DM36x_DDR_PHY_PWRDNEN \
+ | (7 << DM36x_DDR_PHY_RD_LATENCY_SHIFT))
+
+/*
+ * T_RFC = (trfc/DDR_CLK) - 1 = (195 / 2.941) - 1
+ * T_RP = (trp/DDR_CLK) - 1 = (12.5 / 2.941) - 1
+ * T_RCD = (trcd/DDR_CLK) - 1 = (12.5 / 2.941) - 1
+ * T_WR = (twr/DDR_CLK) - 1 = (15 / 2.941) - 1
+ * T_RAS = (tras/DDR_CLK) - 1 = (45 / 2.941) - 1
+ * T_RC = (trc/DDR_CLK) - 1 = (57.5 / 2.941) - 1
+ * T_RRD = (trrd/DDR_CLK) - 1 = (7.5 / 2.941) - 1
+ * T_WTR = (twtr/DDR_CLK) - 1 = (7.5 / 2.941) - 1
+ */
+#define CONFIG_SYS_DM36x_DDR2_SDTIMR (0 \
+ | (66 << DM36x_DDR_SDTMR1_RFC_SHIFT) \
+ | (4 << DM36x_DDR_SDTMR1_RP_SHIFT) \
+ | (4 << DM36x_DDR_SDTMR1_RCD_SHIFT) \
+ | (5 << DM36x_DDR_SDTMR1_WR_SHIFT) \
+ | (14 << DM36x_DDR_SDTMR1_RAS_SHIFT) \
+ | (19 << DM36x_DDR_SDTMR1_RC_SHIFT) \
+ | (2 << DM36x_DDR_SDTMR1_RRD_SHIFT) \
+ | (2 << DM36x_DDR_SDTMR1_WTR_SHIFT))
+
+/*
+ * T_RASMAX = (trasmax/refresh_rate) - 1 = (70K / 7812.6) - 1
+ * T_XP = tCKE - 1 = 3 - 2
+ * T_XSNR= ((trfc + 10)/DDR_CLK) - 1 = (205 / 2.941) - 1
+ * T_XSRD = txsrd - 1 = 200 - 1
+ * T_RTP = (trtp/DDR_CLK) - 1 = (7.5 / 2.941) - 1
+ * T_CKE = tcke - 1 = 3 - 1
+ */
+#define CONFIG_SYS_DM36x_DDR2_SDTIMR2 (0 \
+ | (8 << DM36x_DDR_SDTMR2_RASMAX_SHIFT) \
+ | (2 << DM36x_DDR_SDTMR2_XP_SHIFT) \
+ | (69 << DM36x_DDR_SDTMR2_XSNR_SHIFT) \
+ | (199 << DM36x_DDR_SDTMR2_XSRD_SHIFT) \
+ | (2 << DM36x_DDR_SDTMR2_RTP_SHIFT) \
+ | (2 << DM36x_DDR_SDTMR2_CKE_SHIFT))
+
+/* PR_OLD_COUNT = 0xfe */
+#define CONFIG_SYS_DM36x_DDR2_PBBPR 0x000000FE
+/* refresh rate = 0x768 */
+#define CONFIG_SYS_DM36x_DDR2_SDRCR 0x00000768
+
+#define CONFIG_SYS_DM36x_DDR2_SDBCR (0 \
+ | (2 << DM36x_DDR_SDCR_PAGESIZE_SHIFT) \
+ | (3 << DM36x_DDR_SDCR_IBANK_SHIFT) \
+ | (5 << DM36x_DDR_SDCR_CL_SHIFT) \
+ | (1 << DM36x_DDR_SDCR_BUS_WIDTH_SHIFT) \
+ | (1 << DM36x_DDR_SDCR_TIMUNLOCK_SHIFT) \
+ | (1 << DM36x_DDR_SDCR_DDREN_SHIFT) \
+ | (0 << DM36x_DDR_SDCR_DDRDRIVE0_SHIFT) \
+ | (1 << DM36x_DDR_SDCR_DDR2EN_SHIFT) \
+ | (1 << DM36x_DDR_SDCR_DDR_DDQS_SHIFT) \
+ | (1 << DM36x_DDR_SDCR_BOOTUNLOCK_SHIFT))
+
+#define CONFIG_SYS_DM36x_AWCCR 0xff
+#define CONFIG_SYS_DM36x_AB1CR 0x40400204
+#define CONFIG_SYS_DM36x_AB2CR 0x00a00505
+
+/* All Video Inputs */
+#define CONFIG_SYS_DM36x_PINMUX0 0x00000000
+/*
+ * All Video Outputs,
+ * GPIO 86, 87 + 90 0x0000f030
+ */
+#define CONFIG_SYS_DM36x_PINMUX1 0x0053000a
+#define CONFIG_SYS_DM36x_PINMUX2 0x00001815
+/*
+ * SPI1, UART1, I2C, SD0, SD1, McBSP0, CLKOUTs
+ * GPIO 25 0x60000000
+ */
+#define CONFIG_SYS_DM36x_PINMUX3 0x9b5affff
+/*
+ * MMC/SD0 instead of MS, SPI0
+ * GPIO 34 0x0000c000
+ */
+#define CONFIG_SYS_DM36x_PINMUX4 0x00002655
+
+/*
+ * Default environment settings
+ */
+#define xstr(s) str(s)
+#define str(s) #s
+
+#define DVN4XX_UBOOT_ADDR_R_RAM 0x80000000
+/* (DVN4XX_UBOOT_ADDR_R_RAM + CONFIG_SYS_NAND_PAGE_SIZE) */
+#define DVN4XX_UBOOT_ADDR_R_NAND_SPL 0x80000800
+/*
+ * (DVN4XX_UBOOT_ADDR_R_NAND_SPL + (CONFIG_SYS_NROF_PAGES_NAND_SPL * \
+ * CONFIG_SYS_NAND_PAGE_SIZE))
+ */
+#define DVN4XX_UBOOT_ADDR_R_UBOOT 0x80003800
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "u_boot_addr_r=" xstr(DVN4XX_UBOOT_ADDR_R_RAM) "\0" \
+ "u-boot=" xstr(CONFIG_HOSTNAME) "/u-boot.ubl\0" \
+ "load=tftp ${u_boot_addr_r} ${uboot}\0" \
+ "pagesz=" xstr(CONFIG_SYS_NAND_PAGE_SIZE) "\0" \
+ "writeheader=nand hwfunc rbl;nand erase 80000 ${pagesz};" \
+ "nand write ${u_boot_addr_r} 80000 ${pagesz};" \
+ "nand hwfunc uboot\0" \
+ "writenand_spl=nand hwfunc rbl;nand erase a0000 3000;" \
+ "nand write " xstr(DVN4XX_UBOOT_ADDR_R_NAND_SPL) \
+ " a0000 3000;nand hwfunc uboot\0" \
+ "writeuboot=nand hwfunc uboot;" \
+ "nand erase " xstr(CONFIG_SYS_NAND_U_BOOT_OFFS) " " \
+ xstr(CONFIG_SYS_NAND_U_BOOT_SIZE) \
+ ";nand write " xstr(DVN4XX_UBOOT_ADDR_R_UBOOT) \
+ " " xstr(CONFIG_SYS_NAND_U_BOOT_OFFS) " " \
+ xstr(CONFIG_SYS_NAND_U_BOOT_SIZE) "\0" \
+ "update=run load writenand_spl writeuboot\0" \
+ "bootcmd=run bootcmd\0" \
+ "rootpath=/opt/eldk-arm/arm\0" \
+ "\0"
+
+#endif /* __CONFIG_H */
diff --git a/nand_spl/board/ait/cam_enc_4xx/Makefile b/nand_spl/board/ait/cam_enc_4xx/Makefile
new file mode 100644
index 0000000..4a8728b
--- /dev/null
+++ b/nand_spl/board/ait/cam_enc_4xx/Makefile
@@ -0,0 +1,152 @@
+#
+# (C) Copyright 2006-2007
+# Stefan Roese, DENX Software Engineering, sr at denx.de.
+#
+# (C) Copyright 2008
+# Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+CONFIG_NAND_SPL = y
+
+include $(TOPDIR)/config.mk
+
+nandobj := $(OBJTREE)/nand_spl/
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS := -T $(nandobj)u-boot.lds -N -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \
+ $(LDFLAGS_FINAL)
+AFLAGS += -DCONFIG_PRELOADER -DCONFIG_NAND_SPL
+CFLAGS += -DCONFIG_PRELOADER -DCONFIG_NAND_SPL
+
+SOBJS = start.o _udivsi3.o _divsi3.o
+COBJS = cpu.o davinci_nand.o ns16550.o div0.o davinci_pinmux.o psc.o \
+ misc.o cam_enc_4xx_nand_spl.o nand_boot.o memory.o dm365_lowlevel.o
+
+SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS := $(SOBJS) $(COBJS)
+LNDIR := $(nandobj)board/$(BOARDDIR)
+
+ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin \
+ $(nandobj)u-boot-spl-16k.bin
+
+all: $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
+ -Map $(nandobj)u-boot-spl.map \
+ -o $(nandobj)u-boot-spl
+
+$(nandobj)u-boot.lds: $(LDSCRIPT)
+ $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+# create symbolic links for common files
+
+# from board directory
+$(obj)davinci_pinmux.c:
+ @rm -f $@
+ @ln -s $(TOPDIR)/board/davinci/common/davinci_pinmux.c $@
+
+# from drivers/mtd/nand directory
+$(obj)davinci_nand.c:
+ @rm -f $@
+ @ln -s $(TOPDIR)/drivers/mtd/nand/davinci_nand.c $@
+
+# from nand_spl directory
+$(obj)nand_boot.c:
+ @rm -f $@
+ @ln -s $(TOPDIR)/nand_spl/nand_boot.c $@
+
+# from drivers/serial directory
+$(obj)ns16550.c:
+ @rm -f $@
+ @ln -sf $(TOPDIR)/drivers/serial/ns16550.c $@
+
+# from cpu directory
+$(obj)start.S:
+ @rm -f $@
+ ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/start.S $@
+
+# from lib directory
+$(obj)_udivsi3.S:
+ @rm -f $@
+ ln -s $(TOPDIR)/arch/arm/lib/_udivsi3.S $@
+
+# from lib directory
+$(obj)_divsi3.S:
+ @rm -f $@
+ ln -s $(TOPDIR)/arch/arm/lib/_divsi3.S $@
+
+# from lib directory
+$(obj)div0.c:
+ @rm -f $@
+ ln -s $(TOPDIR)/arch/arm/lib/div0.c $@
+
+# from SoC directory
+$(obj)cpu.c:
+ @rm -f $@
+ @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/cpu.c $@
+
+# from board directory
+$(obj)cam_enc_4xx_nand_spl.c:
+ @rm -f $@
+ ln -s $(TOPDIR)/board/ait/cam_enc_4xx/cam_enc_4xx_nand_spl.c $@
+
+# from board directory
+$(obj)misc.c:
+ @rm -f $@
+ ln -s $(TOPDIR)/board/davinci/common/misc.c $@
+
+$(obj)psc.c:
+ @rm -f $@
+ ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/psc.c $@
+
+# from post directory
+$(obj)memory.c:
+ @rm -f $@
+ @ln -s $(TOPDIR)/post/drivers/memory.c $@
+
+# from cpu directory
+$(obj)dm365_lowlevel.c:
+ @rm -f $@
+ ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/dm365_lowlevel.c $@
+
+
+#########################################################################
+
+$(obj)%.o: $(obj)%.S
+ $(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o: $(obj)%.c
+ $(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/nand_spl/board/ait/cam_enc_4xx/u-boot.lds b/nand_spl/board/ait/cam_enc_4xx/u-boot.lds
new file mode 100644
index 0000000..ec16033
--- /dev/null
+++ b/nand_spl/board/ait/cam_enc_4xx/u-boot.lds
@@ -0,0 +1,75 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj at denx.de>
+ *
+ * (C) Copyright 2008
+ * Guennadi Liakhovetki, DENX Software Engineering, <lg at denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ start.o (.text)
+ cpu.o (.text)
+ nand_boot.o (.text)
+
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ . = ALIGN(4);
+ .data : {
+ *(.data)
+ __datarel_start = .;
+ *(.data.rel)
+ __datarelrolocal_start = .;
+ *(.data.rel.ro.local)
+ __datarellocal_start = .;
+ *(.data.rel.local)
+ __datarelro_start = .;
+ *(.data.rel.ro)
+ }
+
+ . = ALIGN(4);
+ __rel_dyn_start = .;
+ __rel_dyn_end = .;
+ __dynsym_start = .;
+
+ __got_start = .;
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __got_end = .;
+
+ . = ALIGN(4);
+ __bss_start = .;
+ .bss : { *(.bss) }
+ __bss_end__ = .;
+}
--
1.7.6
More information about the U-Boot
mailing list