[U-Boot] [PATCH 15/52] ARM: remove broken "SMN42" board

Wolfgang Denk wd at denx.de
Mon Jul 18 00:16:43 CEST 2011


Signed-off-by: Wolfgang Denk <wd at denx.de>
---
 MAKEALL                 |    1 -
 boards.cfg              |    1 -
 doc/README.scrapyard    |    1 +
 include/configs/SMN42.h |  201 -----------------------------------------------
 4 files changed, 1 insertions(+), 203 deletions(-)
 delete mode 100644 include/configs/SMN42.h

diff --git a/MAKEALL b/MAKEALL
index f1f1ad3..02a6614 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -305,7 +305,6 @@ LIST_SA="$(boards_by_cpu sa1100)"
 LIST_ARM7="		\
 	lpc2292sodimm	\
 	modnet50	\
-	SMN42		\
 "
 
 #########################################################################
diff --git a/boards.cfg b/boards.cfg
index 2d484b8..6d06d03 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -43,7 +43,6 @@ omap2420h4                   arm         arm1136     -                   ti
 tnetv107x_evm                arm         arm1176     tnetv107xevm        ti             tnetv107x
 modnet50                     arm         arm720t
 lpc2292sodimm                arm         arm720t     -                   -              lpc2292
-SMN42                        arm         arm720t     -                   siemens        lpc2292
 a320evb                      arm         arm920t     -                   faraday        a320
 at91rm9200ek                 arm         arm920t     at91rm9200ek        atmel          at91        at91rm9200ek
 at91rm9200ek_ram             arm         arm920t     at91rm9200ek        atmel          at91        at91rm9200ek:RAMBOOT
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 778eb97..5561f77 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,6 +11,7 @@ easily if here is something they might want to dig for...
 
 Board	Arch	CPU	removed	    Commit	last known maintainer/contact
 =============================================================================
+SMN42	arm	arm720t	-	  2011-07-16
 impa7	arm	arm720t	-	  2011-07-16	Marius Gröger <mag at sysgo.de>
 evb4510	arm	arm720t	-	  2011-07-16
 ep7312	arm	arm720t	-	  2011-07-16	Marius Gröger <mag at sysgo.de>
diff --git a/include/configs/SMN42.h b/include/configs/SMN42.h
deleted file mode 100644
index 4a8acab..0000000
--- a/include/configs/SMN42.h
+++ /dev/null
@@ -1,201 +0,0 @@
-/*
- * (C) Copyright 2007
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * Configuation settings for the SMN42 board from Siemens.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * If we are developing, we might want to start u-boot from ram
- * so we MUST NOT initialize critical regs like mem-timing ...
- */
-#undef CONFIG_SKIP_LOWLEVEL_INIT
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_ARM7		1	/* This is a ARM7 CPU	*/
-#define CONFIG_ARM_THUMB	1	/* this is an ARM720TDMI */
-#define CONFIG_LPC2292
-#undef	CONFIG_ARM7_REVD		/* disable ARM720 REV.D Workarounds */
-
-#undef CONFIG_USE_IRQ			/* don't need them anymore */
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
-
-/*
- * Hardware drivers
- */
-
-/*
- * select serial console configuration
- */
-#define CONFIG_LPC2292_SERIAL
-#define CONFIG_SERIAL1		1	/* we use Serial line 1 */
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_BAUDRATE		115200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-/* this would be 0xAE if E0, E1 and E2 were pulled high */
-#define CONFIG_SYS_I2C_SLAVE		0xA0
-#define CONFIG_SYS_I2C_EEPROM_ADDR	(0xA0 >> 1)
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-/* not used but required by devices.c */
-#define CONFIG_SYS_I2C_SPEED 10000
-
-#ifdef CONFIG_SOFT_I2C
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define SCL		0x00000004		/* P0.2 */
-#define SDA		0x00000008		/* P0.3 */
-
-#define	I2C_READ	((GET32(IO0PIN) & SDA) ? 1 : 0)
-#define	I2C_SDA(x)	{ if (x) PUT32(IO0SET, SDA); else PUT32(IO0CLR, SDA); }
-#define	I2C_SCL(x)	{ if (x) PUT32(IO0SET, SCL); else PUT32(IO0CLR, SCL); }
-#define	I2C_DELAY	{ udelay(100); }
-#define	I2C_ACTIVE	{ unsigned int i2ctmp; \
-					  i2ctmp = GET32(IO0DIR); \
-					  i2ctmp |= SDA; \
-					  PUT32(IO0DIR, i2ctmp); }
-#define	I2C_TRISTATE	{ unsigned int i2ctmp; \
-					      i2ctmp = GET32(IO0DIR); \
-					      i2ctmp &= ~SDA; \
-						  PUT32(IO0DIR, i2ctmp); }
-#endif /* CONFIG_SOFT_I2C */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_PING
-
-
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_BOOTDELAY	5
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#define	CONFIG_SYS_PROMPT		"SMN42 # " /* Monitor Command Prompt	*/
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x81800000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x83000000	/* 24 MB in SRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x81000000	/* default load address	*/
-						/* for uClinux img is here*/
-
-#define CONFIG_SYS_SYS_CLK_FREQ	58982400	/* Hz */
-#define	CONFIG_SYS_HZ			2048		/* decrementer freq in Hz */
-
-						/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
-#endif
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS	1	   /* we have 1 bank of SRAM */
-#define PHYS_SDRAM_1		0x81000000 /* SRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE	0x02000000 /* 32 MB SRAM */
-
-/* This is the external flash */
-#define PHYS_FLASH_1		0x80000000 /* Flash Bank #1 */
-#define PHYS_FLASH_SIZE		0x01000000 /* 16 MB */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-/*
- * The first entry in CONFIG_SYS_FLASH_BANKS_LIST is a dummy, but it must be present.
- */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ 0, PHYS_FLASH_1 }
-#define CONFIG_SYS_FLASH_ADDR0			0x555
-#define CONFIG_SYS_FLASH_ADDR1			0x2AA
-#define CONFIG_SYS_FLASH_ERASE_TOUT	16384	/* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	5	/* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_MAX_FLASH_SECT	128  /* max number of sectors on one chip    */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-/* The Environment Sector is in the CPU-internal flash */
-#define CONFIG_SYS_FLASH_BASE		0
-#define CONFIG_ENV_OFFSET		0x3C000
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-#define CONFIG_ENV_SIZE		0x2000 /* Total Size of Environment Sector	*/
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_MMC			1
-/* we use this ethernet chip */
-#define CONFIG_ENC28J60_LPC2292
-
-#endif	/* __CONFIG_H */
-- 
1.7.6



More information about the U-Boot mailing list