[U-Boot] [PATCH 49/52] ARM: remove broken "at91sam9m10g45ek" / "at91sam9g45ekes" boards
Wolfgang Denk
wd at denx.de
Mon Jul 18 00:17:17 CEST 2011
Signed-off-by: Wolfgang Denk <wd at denx.de>
---
MAINTAINERS | 3 -
MAKEALL | 1 -
Makefile | 21 --
board/atmel/at91sam9m10g45ek/Makefile | 55 ----
board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 340 -----------------------
board/atmel/at91sam9m10g45ek/config.mk | 1 -
board/atmel/at91sam9m10g45ek/led.c | 41 ---
doc/README.scrapyard | 2 +
include/configs/at91sam9m10g45ek.h | 226 ---------------
9 files changed, 2 insertions(+), 688 deletions(-)
delete mode 100644 board/atmel/at91sam9m10g45ek/Makefile
delete mode 100644 board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
delete mode 100644 board/atmel/at91sam9m10g45ek/config.mk
delete mode 100644 board/atmel/at91sam9m10g45ek/led.c
delete mode 100644 include/configs/at91sam9m10g45ek.h
diff --git a/MAINTAINERS b/MAINTAINERS
index e5a22ee..f2a8bcb 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -629,9 +629,6 @@ Daniel Gorsulowski <daniel.gorsulowski at esd.eu>
otc570 ARM926EJS (AT91SAM9263 SoC)
-Sedji Gaouaou<sedji.gaouaou at atmel.com>
- at91sam9m10g45ek ARM926EJS (AT91SAM9G45 SoC)
-
Simon Guinot <simon.guinot at sequanux.org>
inetspace_v2 ARM926EJS (Kirkwood SoC)
diff --git a/MAKEALL b/MAKEALL
index c1b5b58..2d3d046 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -395,7 +395,6 @@ LIST_at91="$(boards_by_soc at91)\
$(boards_by_soc at91rm9200)\
at91sam9260ek \
at91sam9g20ek \
- at91sam9m10g45ek \
at91sam9rlek \
pm9g45 \
SBC35_A9G20 \
diff --git a/Makefile b/Makefile
index 0a2ed8e..71a08b0 100644
--- a/Makefile
+++ b/Makefile
@@ -808,27 +808,6 @@ at91sam9rlek_config : unconfig
fi;
@$(MKCONFIG) -n $@ -a at91sam9rlek arm arm926ejs at91sam9rlek atmel at91
-at91sam9m10g45ek_nandflash_config \
-at91sam9m10g45ek_dataflash_config \
-at91sam9m10g45ek_dataflash_cs0_config \
-at91sam9m10g45ek_config \
-at91sam9g45ekes_nandflash_config \
-at91sam9g45ekes_dataflash_config \
-at91sam9g45ekes_dataflash_cs0_config \
-at91sam9g45ekes_config : unconfig
- @mkdir -p $(obj)include
- @if [ "$(findstring 9m10,$@)" ] ; then \
- echo "#define CONFIG_AT91SAM9M10G45EK 1" >>$(obj)include/config.h ; \
- else \
- echo "#define CONFIG_AT91SAM9G45EKES 1" >>$(obj)include/config.h ; \
- fi;
- @if [ "$(findstring _nandflash,$@)" ] ; then \
- echo "#define CONFIG_SYS_USE_NANDFLASH 1" >>$(obj)include/config.h ; \
- else \
- echo "#define CONFIG_ATMEL_SPI 1" >>$(obj)include/config.h ; \
- fi;
- @$(MKCONFIG) -n $@ -a at91sam9m10g45ek arm arm926ejs at91sam9m10g45ek atmel at91
-
pm9g45_config : unconfig
@mkdir -p $(obj)include
@$(MKCONFIG) -a pm9g45 arm arm926ejs pm9g45 ronetix at91
diff --git a/board/atmel/at91sam9m10g45ek/Makefile b/board/atmel/at91sam9m10g45ek/Makefile
deleted file mode 100644
index 7aa2521..0000000
--- a/board/atmel/at91sam9m10g45ek/Makefile
+++ /dev/null
@@ -1,55 +0,0 @@
-#
-# (C) Copyright 2003-2008
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# (C) Copyright 2008
-# Stelian Pop <stelian.pop at leadtechdesign.com>
-# Lead Tech Design <www.leadtechdesign.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS-y += at91sam9m10g45ek.o
-COBJS-y += led.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS-y))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(call cmd_link_o_target, $(OBJS) $(SOBJS))
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
deleted file mode 100644
index f92b20f..0000000
--- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
+++ /dev/null
@@ -1,340 +0,0 @@
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian.pop at leadtechdesign.com>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/sizes.h>
-#include <asm/arch/at91sam9g45.h>
-#include <asm/arch/at91sam9_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
-#include <asm/arch/at91_common.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_rstc.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/io.h>
-#include <asm/arch/hardware.h>
-#include <lcd.h>
-#include <atmel_lcdc.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-#include <net.h>
-#endif
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* ------------------------------------------------------------------------- */
-/*
- * Miscelaneous platform dependent initialisations
- */
-
-#ifdef CONFIG_CMD_NAND
-static void at91sam9m10g45ek_nand_hw_init(void)
-{
- unsigned long csa;
-
- /* Enable CS3 */
- csa = at91_sys_read(AT91_MATRIX_EBICSA);
- at91_sys_write(AT91_MATRIX_EBICSA,
- csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
-
- /* Configure SMC CS3 for NAND/SmartMedia */
- at91_sys_write(AT91_SMC_SETUP(3),
- AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(3),
- AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(3) |
- AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(2));
- at91_sys_write(AT91_SMC_CYCLE(3),
- AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(4));
- at91_sys_write(AT91_SMC_MODE(3),
- AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
- AT91_SMC_EXNWMODE_DISABLE |
-#ifdef CONFIG_SYS_NAND_DBW_16
- AT91_SMC_DBW_16 |
-#else /* CONFIG_SYS_NAND_DBW_8 */
- AT91_SMC_DBW_8 |
-#endif
- AT91_SMC_TDF_(3));
-
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_PIOC);
-
- /* Configure RDY/BSY */
- at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
-
- /* Enable NandFlash */
- at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
-}
-#endif
-
-#ifdef CONFIG_CMD_USB
-static void at91sam9m10g45ek_usb_hw_init(void)
-{
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_PIODE);
-
- at91_set_gpio_output(AT91_PIN_PD1, 0);
- at91_set_gpio_output(AT91_PIN_PD3, 0);
-}
-#endif
-
-#ifdef CONFIG_MACB
-static void at91sam9m10g45ek_macb_hw_init(void)
-{
- unsigned long rstc;
-
- /* Enable clock */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_EMAC);
-
- /*
- * Disable pull-up on:
- * RXDV (PA15) => PHY normal mode (not Test mode)
- * ERX0 (PA12) => PHY ADDR0
- * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA12) |
- pin_to_mask(AT91_PIN_PA13),
- pin_to_controller(AT91_PIN_PA0) + PIO_PUDR);
-
- rstc = at91_sys_read(AT91_RSTC_MR);
-
- /* Need to reset PHY -> 500ms reset */
- at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
- (AT91_RSTC_ERSTL & (0x0D << 8)) |
- AT91_RSTC_URSTEN);
-
- at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
-
- /* Wait for end hardware reset */
- while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
-
- /* Restore NRST value */
- at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
- (rstc) |
- AT91_RSTC_URSTEN);
-
- /* Re-enable pull-up */
- writel(pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA12) |
- pin_to_mask(AT91_PIN_PA13),
- pin_to_controller(AT91_PIN_PA0) + PIO_PUER);
-
- at91_macb_hw_init();
-}
-#endif
-
-#ifdef CONFIG_LCD
-
-vidinfo_t panel_info = {
- vl_col: 480,
- vl_row: 272,
- vl_clk: 9000000,
- vl_sync: ATMEL_LCDC_INVLINE_NORMAL |
- ATMEL_LCDC_INVFRAME_NORMAL,
- vl_bpix: 3,
- vl_tft: 1,
- vl_hsync_len: 45,
- vl_left_margin: 1,
- vl_right_margin:1,
- vl_vsync_len: 1,
- vl_upper_margin:40,
- vl_lower_margin:1,
- mmio: AT91SAM9G45_LCDC_BASE,
-};
-
-
-void lcd_enable(void)
-{
- at91_set_A_periph(AT91_PIN_PE6, 1); /* power up */
-}
-
-void lcd_disable(void)
-{
- at91_set_A_periph(AT91_PIN_PE6, 0); /* power down */
-}
-
-static void at91sam9m10g45ek_lcd_hw_init(void)
-{
- at91_set_A_periph(AT91_PIN_PE0, 0); /* LCDDPWR */
- at91_set_A_periph(AT91_PIN_PE2, 0); /* LCDCC */
- at91_set_A_periph(AT91_PIN_PE3, 0); /* LCDVSYNC */
- at91_set_A_periph(AT91_PIN_PE4, 0); /* LCDHSYNC */
- at91_set_A_periph(AT91_PIN_PE5, 0); /* LCDDOTCK */
-
- at91_set_A_periph(AT91_PIN_PE7, 0); /* LCDD0 */
- at91_set_A_periph(AT91_PIN_PE8, 0); /* LCDD1 */
- at91_set_A_periph(AT91_PIN_PE9, 0); /* LCDD2 */
- at91_set_A_periph(AT91_PIN_PE10, 0); /* LCDD3 */
- at91_set_A_periph(AT91_PIN_PE11, 0); /* LCDD4 */
- at91_set_A_periph(AT91_PIN_PE12, 0); /* LCDD5 */
- at91_set_A_periph(AT91_PIN_PE13, 0); /* LCDD6 */
- at91_set_A_periph(AT91_PIN_PE14, 0); /* LCDD7 */
- at91_set_A_periph(AT91_PIN_PE15, 0); /* LCDD8 */
- at91_set_A_periph(AT91_PIN_PE16, 0); /* LCDD9 */
- at91_set_A_periph(AT91_PIN_PE17, 0); /* LCDD10 */
- at91_set_A_periph(AT91_PIN_PE18, 0); /* LCDD11 */
- at91_set_A_periph(AT91_PIN_PE19, 0); /* LCDD12 */
- at91_set_B_periph(AT91_PIN_PE20, 0); /* LCDD13 */
- at91_set_A_periph(AT91_PIN_PE21, 0); /* LCDD14 */
- at91_set_A_periph(AT91_PIN_PE22, 0); /* LCDD15 */
- at91_set_A_periph(AT91_PIN_PE23, 0); /* LCDD16 */
- at91_set_A_periph(AT91_PIN_PE24, 0); /* LCDD17 */
- at91_set_A_periph(AT91_PIN_PE25, 0); /* LCDD18 */
- at91_set_A_periph(AT91_PIN_PE26, 0); /* LCDD19 */
- at91_set_A_periph(AT91_PIN_PE27, 0); /* LCDD20 */
- at91_set_B_periph(AT91_PIN_PE28, 0); /* LCDD21 */
- at91_set_A_periph(AT91_PIN_PE29, 0); /* LCDD22 */
- at91_set_A_periph(AT91_PIN_PE30, 0); /* LCDD23 */
-
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_LCDC);
-
- gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE;
-}
-
-#ifdef CONFIG_LCD_INFO
-#include <nand.h>
-#include <version.h>
-
-void lcd_show_board_info(void)
-{
- ulong dram_size, nand_size;
- int i;
- char temp[32];
-
- lcd_printf ("%s\n", U_BOOT_VERSION);
- lcd_printf ("(C) 2008 ATMEL Corp\n");
- lcd_printf ("at91support at atmel.com\n");
- lcd_printf ("%s CPU at %s MHz\n",
- CONFIG_SYS_AT91_CPU_NAME,
- strmhz(temp, get_cpu_clk_rate()));
-
- dram_size = 0;
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
- dram_size += gd->bd->bi_dram[i].size;
- nand_size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
- nand_size += nand_info[i].size;
- lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
- dram_size >> 20,
- nand_size >> 20 );
-}
-#endif /* CONFIG_LCD_INFO */
-#endif
-
-int board_init(void)
-{
- /* Enable Ctrlc */
- console_init_f();
-
- /* arch number of AT91SAM9M10G45EK-Board */
-#ifdef CONFIG_AT91SAM9M10G45EK
- gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK;
-#elif defined CONFIG_AT91SAM9G45EKES
- gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G45EKES;
-#endif
- /* adress of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
- at91_serial_hw_init();
-#ifdef CONFIG_CMD_NAND
- at91sam9m10g45ek_nand_hw_init();
-#endif
-#ifdef CONFIG_CMD_USB
- at91sam9m10g45ek_usb_hw_init();
-#endif
-#ifdef CONFIG_HAS_DATAFLASH
- at91_spi0_hw_init(1 << 0);
-#endif
-#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 4);
-#endif
-
-#ifdef CONFIG_MACB
- at91sam9m10g45ek_macb_hw_init();
-#endif
-
-#ifdef CONFIG_LCD
- at91sam9m10g45ek_lcd_hw_init();
-#endif
- return 0;
-}
-
-int dram_init(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
- return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-void reset_phy(void)
-{
-}
-#endif
-
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)AT91SAM9G45_BASE_EMAC, 0x00);
-#endif
- return rc;
-}
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs < 2;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- switch(slave->cs) {
- case 1:
- at91_set_gpio_output(AT91_PIN_PB18, 0);
- break;
- case 0:
- default:
- at91_set_gpio_output(AT91_PIN_PB3, 0);
- break;
- }
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- switch(slave->cs) {
- case 1:
- at91_set_gpio_output(AT91_PIN_PB18, 1);
- break;
- case 0:
- default:
- at91_set_gpio_output(AT91_PIN_PB3, 1);
- break;
- }
-}
-#endif /* CONFIG_ATMEL_SPI */
diff --git a/board/atmel/at91sam9m10g45ek/config.mk b/board/atmel/at91sam9m10g45ek/config.mk
deleted file mode 100644
index 9d3c5ae..0000000
--- a/board/atmel/at91sam9m10g45ek/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x73f00000
diff --git a/board/atmel/at91sam9m10g45ek/led.c b/board/atmel/at91sam9m10g45ek/led.c
deleted file mode 100644
index ff59a2d..0000000
--- a/board/atmel/at91sam9m10g45ek/led.c
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian.pop at leadtechdesign.com>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/arch/at91sam9g45.h>
-#include <asm/arch/at91_pmc.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/io.h>
-
-void coloured_LED_init(void)
-{
- /* Enable clock */
- at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9G45_ID_PIODE);
-
- at91_set_gpio_output(CONFIG_RED_LED, 1);
- at91_set_gpio_output(CONFIG_GREEN_LED, 1);
-
- at91_set_gpio_value(CONFIG_RED_LED, 0);
- at91_set_gpio_value(CONFIG_GREEN_LED, 1);
-}
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index e69470f..56cb8b6 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,6 +11,8 @@ easily if here is something they might want to dig for...
Board Arch CPU removed Commit last known maintainer/contact
=============================================================================
+at91sam9g45ekes arm arm926ejs - 2011-07-17
+at91sam9m10g45ek arm arm926ejs - 2011-07-17 Sedji Gaouaou<sedji.gaouaou at atmel.com>
at91sam9263ek arm arm926ejs - 2011-07-17 Stelian Pop <stelian.pop at leadtechdesign.com>
at91sam9g10ek arm arm926ejs - 2011-07-17 Sedji Gaouaou<sedji.gaouaou at atmel.com>
at91sam9261ek arm arm926ejs - 2011-07-17 Stelian Pop <stelian.pop at leadtechdesign.com>
diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
deleted file mode 100644
index de74dcf..0000000
--- a/include/configs/at91sam9m10g45ek.h
+++ /dev/null
@@ -1,226 +0,0 @@
-/*
- * (C) Copyright 2007-2008
- * Stelian Pop <stelian.pop at leadtechdesign.com>
- * Lead Tech Design <www.leadtechdesign.com>
- *
- * Configuation settings for the AT91SAM9M10G45EK board(and AT91SAM9G45EKES).
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_AT91_LEGACY
-
-/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-#define CONFIG_SYS_HZ 1000
-
-#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
-#ifdef CONFIG_AT91SAM9M10G45EK
-#define CONFIG_AT91SAM9M10G45 1 /* It's an Atmel AT91SAM9M10G45 SoC*/
-#else
-#define CONFIG_AT91SAM9G45 1 /* It's an Atmel AT91SAM9G45 SoC*/
-#endif
-#define CONFIG_ARCH_CPU_INIT
-#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-/*
- * Hardware drivers
- */
-#define CONFIG_AT91_GPIO 1
-#define CONFIG_ATMEL_USART 1
-#undef CONFIG_USART0
-#undef CONFIG_USART1
-#undef CONFIG_USART2
-#define CONFIG_USART3 1 /* USART 3 is DBGU */
-
-/* LCD */
-#define CONFIG_LCD 1
-#define LCD_BPP LCD_COLOR8
-#define CONFIG_LCD_LOGO 1
-#undef LCD_TEST_PATTERN
-#define CONFIG_LCD_INFO 1
-#define CONFIG_LCD_INFO_BELOW_LOGO 1
-#define CONFIG_SYS_WHITE_ON_BLACK 1
-#define CONFIG_ATMEL_LCD 1
-#define CONFIG_ATMEL_LCD_RGB565 1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
-/* board specific(not enough SRAM) */
-#define CONFIG_AT91SAM9G45_LCD_BASE 0x73E00000
-
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED AT91_PIN_PD31 /* this is the user1 led */
-#define CONFIG_GREEN_LED AT91_PIN_PD0 /* this is the user2 led */
-
-#define CONFIG_BOOTDELAY 3
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE 1
-#define CONFIG_BOOTP_BOOTPATH 1
-#define CONFIG_BOOTP_GATEWAY 1
-#define CONFIG_BOOTP_HOSTNAME 1
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_BDI
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMI
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_AUTOSCRIPT
-#undef CONFIG_CMD_LOADS
-
-#define CONFIG_CMD_PING 1
-#define CONFIG_CMD_DHCP 1
-#define CONFIG_CMD_NAND 1
-#define CONFIG_CMD_USB 1
-
-/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM 0x70000000
-#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */
-
-/* DataFlash */
-#ifdef CONFIG_ATMEL_SPI
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_SPI_FLASH 1
-#define CONFIG_SPI_FLASH_ATMEL 1
-#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
-#endif
-
-/* NOR flash, if populated */
-#ifndef CONFIG_CMD_NAND
-#define CONFIG_SYS_NO_FLASH 1
-#else
-#define CONFIG_SYS_FLASH_CFI 1
-#define CONFIG_FLASH_CFI_DRIVER 1
-#define PHYS_FLASH_1 0x10000000
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-#define CONFIG_SYS_MAX_FLASH_SECT 256
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#endif
-
-/* NAND flash */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_MAX_CHIPS 1
-#define CONFIG_NAND_ATMEL
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-#define CONFIG_SYS_NAND_DBW_8 1
-/* our ALE is AD21 */
-#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
-/* our CLE is AD22 */
-#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
-#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC8
-
-#endif
-
-/* Ethernet */
-#define CONFIG_MACB 1
-#define CONFIG_RMII 1
-#define CONFIG_NET_MULTI 1
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_RESET_PHY_R 1
-
-/* USB */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_OHCI_NEW 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* AT91SAM9G45_UHP_OHCI_BASE */
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-#define CONFIG_USB_STORAGE 1
-
-#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END 0x23e00000
-
-#ifdef CONFIG_SYS_USE_DATAFLASH
-
-/* bootstrap + u-boot + env + linux in dataflash on CS0 */
-#define CONFIG_ENV_IS_IN_SPI_FLASH 1
-#define CONFIG_SYS_MONITOR_BASE (0xC0000000 + 0x8400)
-#define CONFIG_ENV_OFFSET 0x4200
-#define CONFIG_ENV_ADDR (0xC0000000 + CONFIG_ENV_OFFSET)
-#define CONFIG_ENV_SIZE 0x4200
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm"
-#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
- "root=/dev/mtdblock0 " \
- "mtdparts=atmel_nand:-(root) "\
- "rw rootfstype=jffs2"
-
-#else /* CONFIG_SYS_USE_NANDFLASH */
-
-/* bootstrap + u-boot + env + linux in nandflash */
-#define CONFIG_ENV_IS_IN_NAND 1
-#define CONFIG_ENV_OFFSET 0x60000
-#define CONFIG_ENV_OFFSET_REDUND 0x80000
-#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
-#define CONFIG_BOOTCOMMAND "nand read 0x72000000 0x200000 0x200000; bootm"
-#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
- "root=/dev/mtdblock5 " \
- "mtdparts=atmel_nand:128k(bootstrap)ro, \
- 256k(uboot)ro,128k(env1)ro,128k(env2)ro, \
- 2M(linux),-(root) " \
- "rw rootfstype=jffs2"
-
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
-
-#define CONFIG_SYS_PROMPT "U-Boot> "
-#define CONFIG_SYS_CBSIZE 256
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
-
-#define CONFIG_STACKSIZE (32*1024) /* regular stack */
-
-#ifdef CONFIG_USE_IRQ
-#error CONFIG_USE_IRQ not supported
-#endif
-
-#endif
--
1.7.6
More information about the U-Boot
mailing list