[U-Boot] [PATCH 3/4] Armada100: Enable 88E3015 PHY support for GplugD

Prafulla Wadaskar prafulla at marvell.com
Mon Jul 18 21:27:24 CEST 2011



> -----Original Message-----
> From: Ajay Bhargav [mailto:ajay.bhargav at einfochips.com]
> Sent: Monday, July 18, 2011 3:12 PM
> To: Prafulla Wadaskar
> Cc: u-boot at lists.denx.de; Ajay Bhargav
> Subject: [PATCH 3/4] Armada100: Enable 88E3015 PHY support for GplugD
> 
> This patch adds support for 88E3015 PHY for Marvell GplugD board.
> 
> Signed-off-by: Ajay Bhargav <ajay.bhargav at einfochips.com>
> ---
>  board/Marvell/gplugd/gplugd.c |   35
> +++++++++++++++++++++++++++++++++++
>  include/configs/gplugd.h      |   14 ++++++++++++++
>  2 files changed, 49 insertions(+), 0 deletions(-)
> 
> diff --git a/board/Marvell/gplugd/gplugd.c
> b/board/Marvell/gplugd/gplugd.c
> index dc7d89d..347a689 100644
> --- a/board/Marvell/gplugd/gplugd.c
> +++ b/board/Marvell/gplugd/gplugd.c
> @@ -32,6 +32,8 @@
>  #include <mvmfp.h>
>  #include <asm/arch/mfp.h>
>  #include <asm/arch/armada100.h>
> +#include <asm/gpio.h>
> +#include <miiphy.h>
> 
>  DECLARE_GLOBAL_DATA_PTR;
> 
> @@ -49,6 +51,7 @@ int board_early_init_f(void)
>  	};
>  	/* configure MFP's */
>  	mfp_config(mfp_cfg);
> +

Remove this unwanted commit line

>  	return 0;
>  }
> 
> @@ -58,5 +61,37 @@ int board_init(void)
>  	gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD;
>  	/* adress of boot parameters */
>  	gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
> +	/* Assert PHY_RST# */
> +	gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_CLR);
> +	udelay(10);
> +	/* Deassert PHY_RST# */
> +	gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_SET);

May you please comment why do you need to set this GPIO?

>  	return 0;
>  }
> +
> +#ifdef CONFIG_RESET_PHY_R
> +/* Configure and initialize PHY chip 88E3015 */
> +void reset_phy(void)
> +{
> +	u16 phy_adr;
> +	const char *name = "armd-fec0";
> +
> +	if (miiphy_set_current_dev(name))
> +		return;
> +
> +	/* command to read PHY dev address */
> +	if (miiphy_read(name, 0xff, 0xff, (u16 *) &phy_adr)) {
> +		printf("Err..%s could not read PHY dev address\n",
> +				__func__);
> +		return;
> +	}
> +
> +	/* Set Ethernet LED in TX blink mode */
> +	miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00);
> +	miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL);
> +
> +	/* reset the phy */
> +	miiphy_reset(name, phy_adr);
> +	printf("88E3015 Initialized on %s\n", name);
> +}
> +#endif /* CONFIG_RESET_PHY_R */
> diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h
> index cc14f49..412c959 100644
> --- a/include/configs/gplugd.h
> +++ b/include/configs/gplugd.h
> @@ -65,6 +65,20 @@
>  #undef CONFIG_CMD_NET
>  #undef CONFIG_CMD_NFS
> 
> +/* GPIO Support */
> +#define CONFIG_ARMADA100_GPIO
> +
> +/* PHY configuration */

This below configuration should be within #ifdef CONFIG_CMD_NET
Or more it to asm/arch/config.h (recommended)

> +#define CONFIG_MII
> +#define CONFIG_CMD_MII
> +#define CONFIG_RESET_PHY_R
> +/* 88E3015 register definition */
> +#define PHY_LED_PAR_SEL_REG		22
> +#define PHY_LED_MAN_REG			25
> +#define PHY_LED_VAL			0x5b	/* LINK LED1, ACT LED2 */
> +/* GPIO Configuration for PHY */
> +#define CONFIG_SYS_GPIO_PHY_RST		104	/* GPIO104 */
> +
>  /*
>   * mv-common.h should be defined after CMD configs since it used them
>   * to enable certain macros

Regards..
Prafulla . .

> --
> 1.7.0.4



More information about the U-Boot mailing list