[U-Boot] [3/5]devkit8000 nand_spl: Add RAM configuration independent of x-loader or CH

[simonschwarzcor at googlemail.com]

OMAP3 relied on the memory config done by X-loader or Configuration Header. This has to be reworked for the implementation of a SPL. This patch configures RAM bank 0 if CONFIG_PRELOADER is set. Settings for Micron-RAM used by devkit8000 are added to mem.h

Signed-off-by: Simon Schwarz <schwarz at corscience.de>
--

diff --git a/arch/arm/cpu/armv7/omap3/sdrc.c b/arch/arm/cpu/armv7/omap3/sdrc.c
index 2a7970b..d9e7313 100644
--- a/arch/arm/cpu/armv7/omap3/sdrc.c
+++ b/arch/arm/cpu/armv7/omap3/sdrc.c
@@ -8,6 +8,9 @@
  * Copyright (C) 2004-2010
  * Texas Instruments Incorporated - http://www.ti.com/
  *
+ * Copyright (C) 2011
+ * Corscience GmbH & Co. KG - Simon Schwarz <schwarz at corscience.de>
+ *
  * Author :
  *     Vaibhav Hiremath <hvaibhav at ti.com>
  *
@@ -36,6 +39,7 @@
 #include <asm/io.h>
 #include <asm/arch/mem.h>
 #include <asm/arch/sys_proto.h>
+#include <asm/utils.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 extern omap3_sysinfo sysinfo;
@@ -133,13 +137,38 @@ void do_sdrc_init(u32 cs, u32 early)
 		sdelay(0x20000);
 	}
 
+#ifdef CONFIG_PRELOADER
+	/* If we use a SPL there is no x-loader nor config header so we have
+	 * to do the job ourselfs
+	 */
+	if (cs == CS0) {
+		sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
+
+		/* General SDRC config */
+		writel(V_MCFG, &sdrc_base->cs[cs].mcfg);
+		writel(V_RFR_CTRL, &sdrc_base->cs[cs].rfr_ctrl);
+
+		/* AC timings */
+		writel(V_ACTIMA_165, &sdrc_actim_base0->ctrla);
+		writel(V_ACTIMB_165, &sdrc_actim_base0->ctrlb);
+
+		/* Initialize */
+		writel(CMD_NOP, &sdrc_base->cs[cs].manual);
+		writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
+		writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+		writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
+
+		writel(V_MR, &sdrc_base->cs[cs].mr);
+	}
+#endif
+
 	/*
 	 * SDRC timings are set up by x-load or config header
 	 * We don't need to redo them here.
 	 * Older x-loads configure only CS0
 	 * configure CS1 to handle this ommission
 	 */
-	if (cs) {
+	if (cs == CS1) {
 		sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
 		sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
 		writel(readl(&sdrc_base->cs[CS0].mcfg),
@@ -163,8 +192,11 @@ void do_sdrc_init(u32 cs, u32 early)
 	 * Test ram in this bank
 	 * Disable if bad or not present
 	 */
-	if (!mem_ok(cs))
+	if (!mem_ok(cs)) {
+		spl_debug("RAM test: FAILED!\n");
 		writel(0, &sdrc_base->cs[cs].mcfg);
+	}
+	spl_debug("RAM test: PASSED!\n");
 }
 
 /*
diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
index f165949..8b39745 100644
--- a/arch/arm/include/asm/arch-omap3/mem.h
+++ b/arch/arm/include/asm/arch-omap3/mem.h
@@ -128,6 +128,33 @@ enum {
 		(MICRON_XSR_165 << 0) | (MICRON_TXP_165 << 8) |	\
 		(MICRON_TWTR_165 << 16))
 
+#define MICRON_RAMTYPE			0x1
+#define MICRON_DDRTYPE			0x0
+#define MICRON_DEEPPD			0x1
+#define MICRON_B32NOT16			0x1
+#define MICRON_BANKALLOCATION	0x2
+#define MICRON_RAMSIZE			((PHYS_SDRAM_1_SIZE/(1024*1024))/2)
+#define MICRON_ADDRMUXLEGACY	0x1
+#define MICRON_CASWIDTH			0x5
+#define MICRON_RASWIDTH			0x2
+#define MICRON_LOCKSTATUS		0x0
+#define MICRON_V_MCFG ((MICRON_LOCKSTATUS << 30) | (MICRON_RASWIDTH << 24) | \
+	(MICRON_CASWIDTH << 20) | (MICRON_ADDRMUXLEGACY << 19) | \
+	(MICRON_RAMSIZE << 8) | (MICRON_BANKALLOCATION << 6) | \
+	(MICRON_B32NOT16 << 4) | (MICRON_DEEPPD << 3) | \
+	(MICRON_DDRTYPE << 2) | (MICRON_RAMTYPE))
+
+#define MICRON_ARCV				2030
+#define MICRON_ARE				0x1
+#define MICRON_V_RFR_CTRL ((MICRON_ARCV << 8) | (MICRON_ARE))
+
+#define MICRON_BL				0x2
+#define MICRON_SIL				0x0
+#define MICRON_CASL				0x3
+#define MICRON_WBST				0x0
+#define MICRON_V_MR ((MICRON_WBST << 9) | (MICRON_CASL << 4) | \
+	(MICRON_SIL << 3) | (MICRON_BL))
+
 /*
  * NUMONYX part of IGEP v2 (165MHz optimized) 6.06ns
  *   ACTIMA
@@ -171,10 +198,15 @@ enum {
 #define V_ACTIMA_165 INFINEON_V_ACTIMA_165
 #define V_ACTIMB_165 INFINEON_V_ACTIMB_165
 #endif
+
 #ifdef CONFIG_OMAP3_MICRON_DDR
-#define V_ACTIMA_165 MICRON_V_ACTIMA_165
-#define V_ACTIMB_165 MICRON_V_ACTIMB_165
+#define V_ACTIMA_165	MICRON_V_ACTIMA_165
+#define V_ACTIMB_165	MICRON_V_ACTIMB_165
+#define V_MCFG			MICRON_V_MCFG
+#define V_RFR_CTRL		MICRON_V_RFR_CTRL
+#define V_MR			MICRON_V_MR
 #endif
+
 #ifdef CONFIG_OMAP3_NUMONYX_DDR
 #define V_ACTIMA_165 NUMONYX_V_ACTIMA_165
 #define V_ACTIMB_165 NUMONYX_V_ACTIMB_165
@@ -184,6 +216,10 @@ enum {
 #error "Please choose the right DDR type in config header"
 #endif
 
+#if defined(CONFIG_PRELOADER) && (!defined(V_MCFG) || !defined(V_RFR_CTRL))
+#error "Please choose the right DDR type in config header"
+#endif
+
 /*
  * GPMC settings -
  * Definitions is as per the following format