[U-Boot] [PATCH 07/20] ppc: add support for ppc based board mgcoge2ne
Heiko Schocher
hs at denx.de
Tue Mar 8 14:30:05 CET 2011
The mgcoge2 board from keymile deploys two different porcessors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
Signed-off-by: Heiko Schocher <hs at denx.de>
cc: Wolfgang Denk <wd at denx.de>
cc: Valentin Longchamp <valentin.longchamp at keymile.com>
---
MAINTAINERS | 1 +
board/keymile/common/common.c | 4 +-
board/keymile/mgcoge/mgcoge.c | 4 +
boards.cfg | 1 +
include/configs/km82xx-common.h | 321 +++++++++++++++++++++++++++++++++++++++
include/configs/mgcoge.h | 292 +-----------------------------------
include/configs/mgcoge2ne.h | 63 ++++++++
7 files changed, 395 insertions(+), 291 deletions(-)
create mode 100644 include/configs/km82xx-common.h
create mode 100644 include/configs/mgcoge2ne.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 9644d38..e4525e4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -428,6 +428,7 @@ Heiko Schocher <hs at denx.de>
jupiter MPC5200
kmeter1 MPC8360
mgcoge MPC8247
+ mgcoge2ne MPC8247
mgcoge2un ARM926EJS (Kirkwood SoC)
mucmc52 MPC5200
muas3001 MPC8270
diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c
index f0b99ed..f723cfa 100644
--- a/board/keymile/common/common.c
+++ b/board/keymile/common/common.c
@@ -22,7 +22,7 @@
*/
#include <common.h>
-#if defined(CONFIG_MGCOGE)
+#if defined(CONFIG_MGCOGE) || defined(CONFIG_MGCOGE2NE)
#include <mpc8260.h>
#endif
#include <ioports.h>
@@ -337,7 +337,7 @@ int ivm_read_eeprom (void)
#define DELAY_ABORT_SEQ 62
#define DELAY_HALF_PERIOD (500 / (CONFIG_SYS_I2C_SPEED / 1000))
-#if defined(CONFIG_MGCOGE)
+#if defined(CONFIG_MGCOGE) || defined(CONFIG_MGCOGE2NE)
#define SDA_MASK 0x00010000
#define SCL_MASK 0x00020000
static void set_pin (int state, unsigned long mask)
diff --git a/board/keymile/mgcoge/mgcoge.c b/board/keymile/mgcoge/mgcoge.c
index 5c9496c..d9b0380 100644
--- a/board/keymile/mgcoge/mgcoge.c
+++ b/board/keymile/mgcoge/mgcoge.c
@@ -286,7 +286,11 @@ phys_size_t initdram (int board_type)
int checkboard(void)
{
+#if defined(CONFIG_MGCOGE)
puts ("Board: Keymile mgcoge");
+#else
+ puts ("Board: Keymile mgcoge2ne");
+#endif
if (ethernet_present ())
puts (" with PIGGY.");
puts ("\n");
diff --git a/boards.cfg b/boards.cfg
index 22cb509..3c45456 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -424,6 +424,7 @@ PQ2FADS-ZU_66MHz_lowboot powerpc mpc8260 mpc8260ads freesca
PQ2FADS-ZU_lowboot powerpc mpc8260 mpc8260ads freescale - MPC8260ADS:ADSTYPE=CONFIG_SYS_PQ2FADS,SYS_TEXT_BASE=0xFF800000
VoVPN-GW_66MHz powerpc mpc8260 vovpn-gw funkwerk - VoVPN-GW:CLKIN_66MHz
mgcoge powerpc mpc8260 - keymile
+mgcoge2ne powerpc mpc8260 mgcoge keymile
SCM powerpc mpc8260 - siemens
TQM8255_AA powerpc mpc8260 tqm8260 tqc - TQM8260:MPC8255,300MHz
TQM8260_AA powerpc mpc8260 tqm8260 tqc - TQM8260:MPC8260,200MHz
diff --git a/include/configs/km82xx-common.h b/include/configs/km82xx-common.h
new file mode 100644
index 0000000..b28cc99
--- /dev/null
+++ b/include/configs/km82xx-common.h
@@ -0,0 +1,321 @@
+/*
+ * (C) Copyright 2007-2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __KM82XX_COMMON
+#define __KM82XX_COMMON
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_CPM2 1 /* Has a CPM2 */
+
+/*
+ * Select serial console configuration
+ *
+ * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ */
+#define CONFIG_CONS_ON_SMC /* Console is on SMC */
+#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
+#undef CONFIG_CONS_NONE /* It's not on external UART */
+#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */
+#define CONFIG_SYS_SMC_RXBUFLEN 128
+#define CONFIG_SYS_MAXIDLE 10
+
+/*
+ * Select ethernet configuration
+ *
+ * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
+ * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
+ * SCC, 1-3 for FCC)
+ *
+ * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
+ * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
+ * must be unset.
+ */
+#define CONFIG_ETHER_ON_SCC /* Ethernet is on SCC */
+#undef CONFIG_ETHER_ON_FCC /* Ethernet is not on FCC */
+#undef CONFIG_ETHER_NONE /* No external Ethernet */
+#define CONFIG_NET_MULTI 1
+
+#define CONFIG_ETHER_INDEX 4
+#define CONFIG_HAS_ETH0
+#define CONFIG_SYS_SCC_TOUT_LOOP 10000000
+
+# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
+
+#ifndef CONFIG_8260_CLKIN
+#define CONFIG_8260_CLKIN 66000000 /* in Hz */
+#endif
+
+#define BOOTFLASH_START 0xFE000000
+
+#define CONFIG_KM_CONSOLE_TTY "ttyCPM0"
+
+#define MTDPARTS_DEFAULT "mtdparts=" \
+ "app:" \
+ "768k(u-boot)," \
+ "128k(env)," \
+ "128k(envred)," \
+ "3072k(free)," \
+ "-(" CONFIG_KM_UBI_PARTITION_NAME ")"
+
+/*
+ * Default environment settings
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_KM_DEF_ENV \
+ "EEprom_ivm=pca9544a:70:4 \0" \
+ "unlock=yes\0" \
+ "newenv=" \
+ "prot off 0xFE0C0000 +0x40000 && " \
+ "era 0xFE0C0000 +0x40000\0" \
+ "rootpath=/opt/eldk/ppc_82xx\0" \
+ ""
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (768 << 10) /* Reserve 768KB for Monitor */
+
+#define CONFIG_ENV_IS_IN_FLASH
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN
+
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
+#define CONFIG_ENV_BUFFER_PRINT 1
+
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00010000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
+#define I2C_READ ((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+#define CONFIG_SYS_IMMR 0xF0000000
+
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/* Hard reset configuration word */
+#define CONFIG_SYS_HRCW_MASTER 0x0604b211
+
+/* No slaves */
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
+
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+#define CONFIG_SYS_HID0_INIT 0
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
+
+#define CONFIG_SYS_HID2 0
+
+#define CONFIG_SYS_SIUMCR 0x4020c200
+#define CONFIG_SYS_SYPCR 0xFFFFFFC3
+#define CONFIG_SYS_BCR 0x10000000
+#define CONFIG_SYS_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK)
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CONFIG_SYS_RMR 0
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_RCCR 0
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus Machine PortSz Device
+ * ---- --- ------- ------ ------
+ * 0 60x GPCM 8 bit FLASH
+ * 1 60x SDRAM 32 bit SDRAM
+ * 3 60x GPCM 8 bit GPIO/PIGGY
+ * 5 60x GPCM 16 bit CFG-Flash
+ *
+ */
+/* Bank 0 - FLASH
+ */
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV2 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_TRLX )
+
+
+/* Bank 1 - 60x bus SDRAM
+ */
+#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
+#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
+
+#define CONFIG_SYS_MPTPR 0x1800
+
+/*-----------------------------------------------------------------------------
+ * Address for Mode Register Set (MRS) command
+ *-----------------------------------------------------------------------------
+ */
+#define CONFIG_SYS_MRS_OFFS 0x00000110
+#define CONFIG_SYS_PSRT 0x0e
+
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_SDRAM_P |\
+ BRx_V)
+
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1
+
+/* SDRAM initialization values
+*/
+
+#define CONFIG_SYS_OR1 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_8 |\
+ ORxS_ROWST_PBI0_A7 |\
+ ORxS_NUMR_13)
+
+#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5 |\
+ PSDMR_BSMA_A14_A16 |\
+ PSDMR_SDA10_PBI0_A9 |\
+ PSDMR_RFRC_5_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_1C |\
+ PSDMR_CL_2)
+
+/* GPIO/PIGGY on CS3 initialization values
+*/
+#define CONFIG_SYS_PIGGY_BASE 0x30000000
+#define CONFIG_SYS_PIGGY_SIZE 128
+
+#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIGGY_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) |\
+ ORxG_CSNT | ORxG_ACS_DIV2 |\
+ ORxG_SCY_3_CLK | ORxG_TRLX )
+
+/* Board FPGA on CS4 initialization values
+*/
+#define CONFIG_SYS_FPGA_BASE 0x40000000
+#define CONFIG_SYS_FPGA_SIZE 1 /*1KB*/
+
+#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_FPGA_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FPGA_SIZE << 10) |\
+ ORxG_CSNT | ORxG_ACS_DIV2 |\
+ ORxG_SCY_3_CLK | ORxG_TRLX )
+
+/* CFG-Flash on CS5 initialization values
+*/
+#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FLASH_BASE_1 & BRx_BA_MSK) |\
+ BRx_PS_16 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR5_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE_1 + \
+ CONFIG_SYS_FLASH_SIZE_2) |\
+ ORxG_CSNT | ORxG_ACS_DIV2 |\
+ ORxG_SCY_5_CLK | ORxG_TRLX )
+
+#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
+
+/* pass open firmware flat tree */
+#define CONFIG_FIT 1
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc/cpm/serial at 11a90"
+
+#endif /* __KM82XX_COMMON */
diff --git a/include/configs/mgcoge.h b/include/configs/mgcoge.h
index 27f50a6..fbe8cdd 100644
--- a/include/configs/mgcoge.h
+++ b/include/configs/mgcoge.h
@@ -36,78 +36,10 @@
#define CONFIG_SYS_TEXT_BASE 0xFE000000
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
/* include common defines/options for all Keymile boards */
#include "keymile-common.h"
#include "km-powerpc.h"
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define CONFIG_CONS_ON_SMC /* Console is on SMC */
-#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
-#undef CONFIG_CONS_NONE /* It's not on external UART */
-#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */
-#define CONFIG_SYS_SMC_RXBUFLEN 128
-#define CONFIG_SYS_MAXIDLE 10
-
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
-#define CONFIG_ETHER_ON_SCC /* Ethernet is on SCC */
-#undef CONFIG_ETHER_ON_FCC /* Ethernet is not on FCC */
-#undef CONFIG_ETHER_NONE /* No external Ethernet */
-#define CONFIG_NET_MULTI 1
-
-#define CONFIG_ETHER_INDEX 4
-#define CONFIG_HAS_ETH0
-#define CONFIG_SYS_SCC_TOUT_LOOP 10000000
-
-# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN 66000000 /* in Hz */
-#endif
-
-#define BOOTFLASH_START 0xFE000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyCPM0"
-
-#define MTDIDS_DEFAULT "nor3=app"
-#define MTDPARTS_DEFAULT "mtdparts=" \
- "app:" \
- "768k(u-boot)," \
- "128k(env)," \
- "128k(envred)," \
- "3072k(free)," \
- "-(" CONFIG_KM_UBI_PARTITION_NAME ")"
-
-/*
- * Default environment settings
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- "EEprom_ivm=pca9544a:70:4 \0" \
- "unlock=yes\0" \
- "newenv=" \
- "prot off 0xFE0C0000 +0x40000 && " \
- "era 0xFE0C0000 +0x40000\0" \
- "rootpath=/opt/eldk/ppc_82xx\0" \
- ""
-
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0xFE000000
#define CONFIG_SYS_FLASH_SIZE 32
@@ -125,227 +57,9 @@
CONFIG_SYS_FLASH_BASE_1, \
CONFIG_SYS_FLASH_BASE_2 }
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (768 << 10) /* Reserve 768KB for Monitor */
-
-#define CONFIG_ENV_IS_IN_FLASH
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-#define CONFIG_ENV_BUFFER_PRINT 1
-
-/* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-#define CONFIG_SYS_IMMR 0xF0000000
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Hard reset configuration word */
-#define CONFIG_SYS_HRCW_MASTER 0x0604b211
-
-/* No slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#define CONFIG_SYS_HID0_INIT 0
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
-
-#define CONFIG_SYS_HID2 0
-
-#define CONFIG_SYS_SIUMCR 0x4020c200
-#define CONFIG_SYS_SYPCR 0xFFFFFFC3
-#define CONFIG_SYS_BCR 0x10000000
-#define CONFIG_SYS_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK)
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register 5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR 0
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 8 bit FLASH
- * 1 60x SDRAM 32 bit SDRAM
- * 3 60x GPCM 8 bit GPIO/PIGGY
- * 5 60x GPCM 16 bit CFG-Flash
- *
- */
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV2 |\
- ORxG_SCY_5_CLK |\
- ORxG_TRLX )
-
-
-/* Bank 1 - 60x bus SDRAM
- */
-#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
-#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
-
-#define CONFIG_SYS_MPTPR 0x1800
-
-/*-----------------------------------------------------------------------------
- * Address for Mode Register Set (MRS) command
- *-----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_MRS_OFFS 0x00000110
-#define CONFIG_SYS_PSRT 0x0e
-
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1
-
-/* SDRAM initialization values
-*/
-
-#define CONFIG_SYS_OR1 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
- ORxS_BPD_8 |\
- ORxS_ROWST_PBI0_A7 |\
- ORxS_NUMR_13)
-
-#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5 |\
- PSDMR_BSMA_A14_A16 |\
- PSDMR_SDA10_PBI0_A9 |\
- PSDMR_RFRC_5_CLK |\
- PSDMR_PRETOACT_2W |\
- PSDMR_ACTTORW_2W |\
- PSDMR_LDOTOPRE_1C |\
- PSDMR_WRC_1C |\
- PSDMR_CL_2)
-
-/* GPIO/PIGGY on CS3 initialization values
-*/
-#define CONFIG_SYS_PIGGY_BASE 0x30000000
-#define CONFIG_SYS_PIGGY_SIZE 128
-
-#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIGGY_BASE & BRx_BA_MSK) |\
- BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
-
-#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) |\
- ORxG_CSNT | ORxG_ACS_DIV2 |\
- ORxG_SCY_3_CLK | ORxG_TRLX )
-
-/* Board FPGA on CS4 initialization values
-*/
-#define CONFIG_SYS_FPGA_BASE 0x40000000
-#define CONFIG_SYS_FPGA_SIZE 1 /*1KB*/
-
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_FPGA_BASE & BRx_BA_MSK) |\
- BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FPGA_SIZE << 10) |\
- ORxG_CSNT | ORxG_ACS_DIV2 |\
- ORxG_SCY_3_CLK | ORxG_TRLX )
-
-/* CFG-Flash on CS5 initialization values
-*/
-#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FLASH_BASE_1 & BRx_BA_MSK) |\
- BRx_PS_16 | BRx_MS_GPCM_P | BRx_V)
-
-#define CONFIG_SYS_OR5_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE_1 + \
- CONFIG_SYS_FLASH_SIZE_2) |\
- ORxG_CSNT | ORxG_ACS_DIV2 |\
- ORxG_SCY_5_CLK | ORxG_TRLX )
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
-
-/* pass open firmware flat tree */
-#define CONFIG_FIT 1
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
+#define MTDIDS_DEFAULT "nor3=app"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc/cpm/serial at 11a90"
+/* include further common stuff for all keymile 82xx boards */
+#include "km82xx-common.h"
#endif /* __CONFIG_H */
diff --git a/include/configs/mgcoge2ne.h b/include/configs/mgcoge2ne.h
new file mode 100644
index 0000000..d99d83e
--- /dev/null
+++ b/include/configs/mgcoge2ne.h
@@ -0,0 +1,63 @@
+/*
+ * (C) Copyright 2007-2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __MGCOGE2NE
+#define __MGCOGE2NE
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8247 1
+#define CONFIG_MPC8272_FAMILY 1
+#define CONFIG_MGCOGE 1
+#define CONFIG_HOSTNAME mgcoge2ne
+
+#define CONFIG_SYS_TEXT_BASE 0xFE000000
+
+/* include common defines/options for all Keymile boards */
+#include "keymile-common.h"
+#include "km-powerpc.h"
+
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFE000000
+#define CONFIG_SYS_FLASH_SIZE 32
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max num of flash banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+
+#define CONFIG_SYS_FLASH_BASE_1 0x50000000
+#define CONFIG_SYS_FLASH_SIZE_1 64
+#define CONFIG_SYS_FLASH_SIZE_2 0
+
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \
+ CONFIG_SYS_FLASH_BASE_1 }
+
+#define MTDIDS_DEFAULT "nor2=app"
+
+/* include further common stuff for all keymile 82xx boards */
+#include "km82xx-common.h"
+
+#endif /* __MGCOGE2NE */
--
1.7.4
More information about the U-Boot
mailing list