[U-Boot] [PATCH v3 11/23] ppc: add support for ppc based board mgcoge2ne

Heiko Schocher hs at denx.de
Mon Mar 21 08:02:07 CET 2011


The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.

Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
Signed-off-by: Heiko Schocher <hs at denx.de>
cc: Wolfgang Denk <wd at denx.de>
cc: Valentin Longchamp <valentin.longchamp at keymile.com>
---
Changes for v2:
  - fix checkpatch.pl errors and warnings
Changes for v3:
  - rebased only

 MAINTAINERS                     |    1 +
 board/keymile/common/common.c   |    4 +-
 board/keymile/mgcoge/mgcoge.c   |    4 +
 boards.cfg                      |    1 +
 include/configs/km82xx-common.h |  336 +++++++++++++++++++++++++++++++++++++++
 include/configs/mgcoge.h        |  312 +-----------------------------------
 include/configs/mgcoge2ne.h     |   64 ++++++++
 7 files changed, 411 insertions(+), 311 deletions(-)
 create mode 100644 include/configs/km82xx-common.h
 create mode 100644 include/configs/mgcoge2ne.h

diff --git a/MAINTAINERS b/MAINTAINERS
index 9644d38..e4525e4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -428,6 +428,7 @@ Heiko Schocher <hs at denx.de>
 	jupiter		MPC5200
 	kmeter1		MPC8360
 	mgcoge		MPC8247
+	mgcoge2ne	MPC8247
 	mgcoge2un	ARM926EJS (Kirkwood SoC)
 	mucmc52		MPC5200
 	muas3001	MPC8270
diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c
index 85538d0..8564b9c 100644
--- a/board/keymile/common/common.c
+++ b/board/keymile/common/common.c
@@ -22,7 +22,7 @@
  */
 
 #include <common.h>
-#if defined(CONFIG_MGCOGE)
+#if defined(CONFIG_MGCOGE) || defined(CONFIG_MGCOGE2NE)
 #include <mpc8260.h>
 #endif
 #include <ioports.h>
@@ -343,7 +343,7 @@ int ivm_read_eeprom(void)
 #define DELAY_ABORT_SEQ		62
 #define DELAY_HALF_PERIOD	(500 / (CONFIG_SYS_I2C_SPEED / 1000))
 
-#if defined(CONFIG_MGCOGE)
+#if defined(CONFIG_MGCOGE) || defined(CONFIG_MGCOGE2NE)
 #define SDA_MASK	0x00010000
 #define SCL_MASK	0x00020000
 static void set_pin(int state, unsigned long mask)
diff --git a/board/keymile/mgcoge/mgcoge.c b/board/keymile/mgcoge/mgcoge.c
index de80aa5..e32ff98 100644
--- a/board/keymile/mgcoge/mgcoge.c
+++ b/board/keymile/mgcoge/mgcoge.c
@@ -284,7 +284,11 @@ phys_size_t initdram(int board_type)
 
 int checkboard(void)
 {
+#if defined(CONFIG_MGCOGE)
 	puts("Board: Keymile mgcoge");
+#else
+	puts("Board: Keymile mgcoge2ne");
+#endif
 	if (ethernet_present())
 		puts(" with PIGGY.");
 	puts("\n");
diff --git a/boards.cfg b/boards.cfg
index 22cb509..3c45456 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -424,6 +424,7 @@ PQ2FADS-ZU_66MHz_lowboot     powerpc     mpc8260     mpc8260ads          freesca
 PQ2FADS-ZU_lowboot           powerpc     mpc8260     mpc8260ads          freescale      -           MPC8260ADS:ADSTYPE=CONFIG_SYS_PQ2FADS,SYS_TEXT_BASE=0xFF800000
 VoVPN-GW_66MHz               powerpc     mpc8260     vovpn-gw            funkwerk       -           VoVPN-GW:CLKIN_66MHz
 mgcoge                       powerpc     mpc8260     -                   keymile
+mgcoge2ne                    powerpc     mpc8260     mgcoge              keymile
 SCM                          powerpc     mpc8260     -                   siemens
 TQM8255_AA                   powerpc     mpc8260     tqm8260             tqc            -           TQM8260:MPC8255,300MHz
 TQM8260_AA                   powerpc     mpc8260     tqm8260             tqc            -           TQM8260:MPC8260,200MHz
diff --git a/include/configs/km82xx-common.h b/include/configs/km82xx-common.h
new file mode 100644
index 0000000..f0a5893
--- /dev/null
+++ b/include/configs/km82xx-common.h
@@ -0,0 +1,336 @@
+/*
+ * (C) Copyright 2007-2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __KM82XX_COMMON
+#define __KM82XX_COMMON
+
+/*
+ * Select serial console configuration
+ *
+ * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ */
+#define	CONFIG_CONS_ON_SMC		/* Console is on SMC         */
+#undef  CONFIG_CONS_ON_SCC		/* It's not on SCC           */
+#undef	CONFIG_CONS_NONE		/* It's not on external UART */
+#define CONFIG_CONS_INDEX	2	/* SMC2 is used for console  */
+#define CONFIG_SYS_SMC_RXBUFLEN	128
+#define CONFIG_SYS_MAXIDLE	10
+
+/*
+ * Select ethernet configuration
+ *
+ * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
+ * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
+ * SCC, 1-3 for FCC)
+ *
+ * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
+ * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
+ * must be unset.
+ */
+#define	CONFIG_ETHER_ON_SCC		/* Ethernet is on SCC */
+#undef	CONFIG_ETHER_ON_FCC		/* Ethernet is not on FCC     */
+#undef	CONFIG_ETHER_NONE		/* No external Ethernet   */
+#define CONFIG_NET_MULTI
+
+#define CONFIG_ETHER_INDEX	4
+#define CONFIG_HAS_ETH0
+#define CONFIG_SYS_SCC_TOUT_LOOP	10000000
+
+#define CONFIG_SYS_CMXSCR_VALUE	(CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
+
+#ifndef CONFIG_8260_CLKIN
+#define CONFIG_8260_CLKIN	66000000	/* in Hz */
+#endif
+
+#define BOOTFLASH_START		0xFE000000
+
+#define CONFIG_KM_CONSOLE_TTY	"ttyCPM0"
+
+#define MTDPARTS_DEFAULT	"mtdparts="				\
+	"app:"								\
+		"768k(u-boot),"						\
+		"128k(env),"						\
+		"128k(envred),"						\
+		"3072k(free),"						\
+		"-(" CONFIG_KM_UBI_PARTITION_NAME ")"
+
+/*
+ * Default environment settings
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_KM_DEF_ENV						\
+	"EEprom_ivm=pca9544a:70:4 \0"					\
+	"unlock=yes\0"							\
+	"newenv="							\
+		"prot off 0xFE0C0000 +0x40000 && "			\
+		"era 0xFE0C0000 +0x40000\0"				\
+	"rootpath=/opt/eldk/ppc_82xx\0"					\
+	""
+
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN		(768 << 10)
+
+#define CONFIG_ENV_IS_IN_FLASH
+
+#ifdef CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE	0x20000
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
+					CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_OFFSET	CONFIG_SYS_MONITOR_LEN
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
+						CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND		(CONFIG_ENV_SIZE)
+#endif /* CONFIG_ENV_IS_IN_FLASH */
+
+/* enable I2C and select the hardware/software driver */
+#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CONFIG_SYS_I2C_SPEED		50000	/* I2C speed */
+#define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address */
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+
+#define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE	(iop->pdir |=  0x00010000)
+#define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
+#define I2C_READ	((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit)	do { \
+				if (bit) \
+					iop->pdat |=  0x00010000; \
+				else \
+					iop->pdat &= ~0x00010000; \
+			} while (0)
+#define I2C_SCL(bit)	do { \
+				if (bit) \
+					iop->pdat |=  0x00020000; \
+				else \
+					iop->pdat &= ~0x00020000; \
+			} while (0)
+#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
+#define CONFIG_DTT_LM75			/* ON Semi's LM75		*/
+#define CONFIG_DTT_SENSORS	{0}	/* Sensor addresses		*/
+#define CONFIG_SYS_DTT_MAX_TEMP	70
+#define CONFIG_SYS_DTT_LOW_TEMP	-30
+#define CONFIG_SYS_DTT_HYSTERESIS	3
+#define CONFIG_SYS_DTT_BUS_NUM		(CONFIG_SYS_MAX_I2C_BUS)
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+#define CONFIG_SYS_IMMR		0xF0000000
+
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE	0x2000 /* used size in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+						GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/* Hard reset configuration word */
+#define CONFIG_SYS_HRCW_MASTER		0x0604b211
+
+/* No slaves */
+#define CONFIG_SYS_HRCW_SLAVE1		0
+#define CONFIG_SYS_HRCW_SLAVE2		0
+#define CONFIG_SYS_HRCW_SLAVE3		0
+#define CONFIG_SYS_HRCW_SLAVE4		0
+#define CONFIG_SYS_HRCW_SLAVE5		0
+#define CONFIG_SYS_HRCW_SLAVE6		0
+#define CONFIG_SYS_HRCW_SLAVE7		0
+
+/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
+
+#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#  define CONFIG_SYS_CACHELINE_SHIFT	5 /* log base 2 of the above value */
+#endif
+
+#define CONFIG_SYS_HID0_INIT		0
+#define CONFIG_SYS_HID0_FINAL		(HID0_ICE | HID0_IFEM | HID0_ABE)
+
+#define CONFIG_SYS_HID2		0
+
+#define CONFIG_SYS_SIUMCR		0x4020c200
+#define CONFIG_SYS_SYPCR		0xFFFFFFC3
+#define CONFIG_SYS_BCR			0x10000000
+#define CONFIG_SYS_SCCR		(SCCR_PCI_MODE | SCCR_PCI_MODCK)
+
+/*
+ *-----------------------------------------------------------------------
+ * RMR - Reset Mode Register                                     5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CONFIG_SYS_RMR         0
+
+/*
+ *-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control                     4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*
+ *-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control                 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CONFIG_SYS_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*
+ *-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration                         13-7
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SYS_RCCR        0
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus     Machine PortSz  Device
+ * ---- ---     ------- ------  ------
+ *  0   60x     GPCM     8 bit  FLASH
+ *  1   60x     SDRAM   32 bit  SDRAM
+ *  3   60x     GPCM     8 bit  GPIO/PIGGY
+ *  5   60x     GPCM    16 bit  CFG-Flash
+ *
+ */
+/* Bank 0 - FLASH
+ */
+#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)	|\
+			 BRx_PS_8			|\
+			 BRx_MS_GPCM_P			|\
+			 BRx_V)
+
+#define CONFIG_SYS_OR0_PRELIM  (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE)	|\
+			 ORxG_CSNT			|\
+			 ORxG_ACS_DIV2			|\
+			 ORxG_SCY_5_CLK			|\
+			 ORxG_TRLX)
+
+
+/*
+ * Bank 1 - 60x bus SDRAM
+ */
+#define SDRAM_MAX_SIZE	0x08000000	/* max. 128 MB		*/
+#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT	(256 << 20)	/* less than 256 MB */
+
+#define CONFIG_SYS_MPTPR       0x1800
+
+/*
+ *-----------------------------------------------------------------------------
+ * Address for Mode Register Set (MRS) command
+ *-----------------------------------------------------------------------------
+ */
+#define CONFIG_SYS_MRS_OFFS	0x00000110
+#define CONFIG_SYS_PSRT        0x0e
+
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
+			 BRx_PS_64		|\
+			 BRx_MS_SDRAM_P		|\
+			 BRx_V)
+
+#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR1
+
+/*
+ *  SDRAM initialization values
+ */
+
+#define CONFIG_SYS_OR1 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+			 ORxS_BPD_8			|\
+			 ORxS_ROWST_PBI0_A7		|\
+			 ORxS_NUMR_13)
+
+#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5	|\
+			 PSDMR_BSMA_A14_A16	|\
+			 PSDMR_SDA10_PBI0_A9	|\
+			 PSDMR_RFRC_5_CLK	|\
+			 PSDMR_PRETOACT_2W	|\
+			 PSDMR_ACTTORW_2W	|\
+			 PSDMR_LDOTOPRE_1C	|\
+			 PSDMR_WRC_1C		|\
+			 PSDMR_CL_2)
+
+/*
+ * GPIO/PIGGY on CS3 initialization values
+ */
+#define CONFIG_SYS_PIGGY_BASE	0x30000000
+#define CONFIG_SYS_PIGGY_SIZE	128
+
+#define CONFIG_SYS_BR3_PRELIM	((CONFIG_SYS_PIGGY_BASE & BRx_BA_MSK) |\
+			 BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR3_PRELIM	(MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) |\
+			 ORxG_CSNT | ORxG_ACS_DIV2 |\
+			 ORxG_SCY_3_CLK | ORxG_TRLX)
+
+/*
+ * Board FPGA on CS4 initialization values
+ */
+#define CONFIG_SYS_FPGA_BASE	0x40000000
+#define CONFIG_SYS_FPGA_SIZE	1 /*1KB*/
+
+#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_FPGA_BASE & BRx_BA_MSK) |\
+			BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FPGA_SIZE << 10) |\
+			 ORxG_CSNT | ORxG_ACS_DIV2 |\
+			 ORxG_SCY_3_CLK | ORxG_TRLX)
+
+/*
+ * CFG-Flash on CS5 initialization values
+ */
+#define CONFIG_SYS_BR5_PRELIM	((CONFIG_SYS_FLASH_BASE_1 & BRx_BA_MSK) |\
+			 BRx_PS_16 | BRx_MS_GPCM_P | BRx_V)
+
+#define CONFIG_SYS_OR5_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE_1 + \
+				 CONFIG_SYS_FLASH_SIZE_2) |\
+				 ORxG_CSNT | ORxG_ACS_DIV2 |\
+				 ORxG_SCY_5_CLK | ORxG_TRLX)
+
+#define	CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC	/* "bad" address */
+
+/* pass open firmware flat tree */
+#define CONFIG_FIT		1
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+#define OF_TBCLK		(bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH		"/soc/cpm/serial at 11a90"
+
+#endif /* __KM82XX_COMMON */
diff --git a/include/configs/mgcoge.h b/include/configs/mgcoge.h
index 05ba433..3d2ee24 100644
--- a/include/configs/mgcoge.h
+++ b/include/configs/mgcoge.h
@@ -39,72 +39,6 @@
 #include "keymile-common.h"
 #include "km-powerpc.h"
 
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define	CONFIG_CONS_ON_SMC		/* Console is on SMC         */
-#undef  CONFIG_CONS_ON_SCC		/* It's not on SCC           */
-#undef	CONFIG_CONS_NONE		/* It's not on external UART */
-#define CONFIG_CONS_INDEX	2	/* SMC2 is used for console  */
-#define CONFIG_SYS_SMC_RXBUFLEN	128
-#define CONFIG_SYS_MAXIDLE	10
-
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
-#define	CONFIG_ETHER_ON_SCC		/* Ethernet is on SCC */
-#undef	CONFIG_ETHER_ON_FCC		/* Ethernet is not on FCC     */
-#undef	CONFIG_ETHER_NONE		/* No external Ethernet   */
-#define CONFIG_NET_MULTI
-
-#define CONFIG_ETHER_INDEX	4
-#define CONFIG_HAS_ETH0
-#define CONFIG_SYS_SCC_TOUT_LOOP	10000000
-
-# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8)
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN	66000000	/* in Hz */
-#endif
-
-#define BOOTFLASH_START		0xFE000000
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyCPM0"
-
-#define MTDIDS_DEFAULT		"nor3=app"
-#define MTDPARTS_DEFAULT	"mtdparts="				\
-	"app:"								\
-		"768k(u-boot),"						\
-		"128k(env),"						\
-		"128k(envred),"						\
-		"3072k(free),"						\
-		"-(" CONFIG_KM_UBI_PARTITION_NAME ")"
-
-/*
- * Default environment settings
- */
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CONFIG_KM_DEF_ENV						\
-	"EEprom_ivm=pca9544a:70:4 \0"					\
-	"unlock=yes\0"							\
-	"newenv="							\
-		"prot off 0xFE0C0000 +0x40000 && "			\
-		"era 0xFE0C0000 +0x40000\0"				\
-	"rootpath=/opt/eldk/ppc_82xx\0"					\
-	""
-
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		0xFE000000
 #define CONFIG_SYS_FLASH_SIZE		32
@@ -122,249 +56,9 @@
 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \
 					CONFIG_SYS_FLASH_BASE_1, \
 					CONFIG_SYS_FLASH_BASE_2 }
+#define MTDIDS_DEFAULT		"nor3=app"
 
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(768 << 10)
-
-#define CONFIG_ENV_IS_IN_FLASH
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
-				CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_OFFSET	CONFIG_SYS_MONITOR_LEN
-
-/* Address and size of Redundant Environment Sector	*/
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
-					CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND		(CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-#define CONFIG_ENV_BUFFER_PRINT
-
-/* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		50000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-
-#define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE	(iop->pdir |=  0x00010000)
-#define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
-#define I2C_READ	((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit)	do { \
-				if (bit) \
-					iop->pdat |=  0x00010000; \
-				else \
-					iop->pdat &= ~0x00010000; \
-			} while (0)
-#define I2C_SCL(bit)	do { \
-				if (bit) \
-					iop->pdat |=  0x00020000; \
-				else \
-					iop->pdat &= ~0x00020000; \
-			} while (0)
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75		/* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS	{0}	/* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP	70
-#define CONFIG_SYS_DTT_LOW_TEMP	-30
-#define CONFIG_SYS_DTT_HYSTERESIS	3
-#define CONFIG_SYS_DTT_BUS_NUM		(CONFIG_SYS_MAX_I2C_BUS)
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-#define CONFIG_SYS_IMMR		0xF0000000
-
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Hard reset configuration word */
-#define CONFIG_SYS_HRCW_MASTER		0x0604b211
-
-/* No slaves */
-#define CONFIG_SYS_HRCW_SLAVE1		0
-#define CONFIG_SYS_HRCW_SLAVE2		0
-#define CONFIG_SYS_HRCW_SLAVE3		0
-#define CONFIG_SYS_HRCW_SLAVE4		0
-#define CONFIG_SYS_HRCW_SLAVE5		0
-#define CONFIG_SYS_HRCW_SLAVE6		0
-#define CONFIG_SYS_HRCW_SLAVE7		0
-
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5 /* log base 2 of the above value */
-#endif
-
-#define CONFIG_SYS_HID0_INIT		0
-#define CONFIG_SYS_HID0_FINAL		(HID0_ICE | HID0_IFEM | HID0_ABE)
-
-#define CONFIG_SYS_HID2		0
-
-#define CONFIG_SYS_SIUMCR		0x4020c200
-#define CONFIG_SYS_SYPCR		0xFFFFFFC3
-#define CONFIG_SYS_BCR			0x10000000
-#define CONFIG_SYS_SCCR		(SCCR_PCI_MODE | SCCR_PCI_MODCK)
-
-/*
- *-----------------------------------------------------------------------
- * RMR - Reset Mode Register                                     5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR         0
-
-/*
- *-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control                     4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*
- *-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control                 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*
- *-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration                         13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR        0
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus     Machine PortSz  Device
- * ---- ---     ------- ------  ------
- *  0   60x     GPCM     8 bit  FLASH
- *  1   60x     SDRAM   32 bit  SDRAM
- *  3   60x     GPCM     8 bit  GPIO/PIGGY
- *  5   60x     GPCM    16 bit  CFG-Flash
- *
- */
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)	|\
-			 BRx_PS_8			|\
-			 BRx_MS_GPCM_P			|\
-			 BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM  (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE)	|\
-			 ORxG_CSNT			|\
-			 ORxG_ACS_DIV2			|\
-			 ORxG_SCY_5_CLK			|\
-			 ORxG_TRLX )
-
-
-/*
- * Bank 1 - 60x bus SDRAM
- */
-#define SDRAM_MAX_SIZE	0x08000000	/* max. 128 MB		*/
-#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT	(256 << 20)
-
-#define CONFIG_SYS_MPTPR       0x1800
-
-/*
- *-----------------------------------------------------------------------------
- * Address for Mode Register Set (MRS) command
- *-----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_MRS_OFFS	0x00000110
-#define CONFIG_SYS_PSRT        0x0e
-
-#define CONFIG_SYS_BR1_PRELIM  ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK)  |\
-			 BRx_PS_64                      |\
-			 BRx_MS_SDRAM_P                 |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR1
-
-/*
- * SDRAM initialization values
- */
-
-#define CONFIG_SYS_OR1    ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
-			 ORxS_BPD_8                     |\
-			 ORxS_ROWST_PBI0_A7		|\
-			 ORxS_NUMR_13)
-
-#define CONFIG_SYS_PSDMR  (PSDMR_SDAM_A14_IS_A5 |\
-			 PSDMR_BSMA_A14_A16           |\
-			 PSDMR_SDA10_PBI0_A9		|\
-			 PSDMR_RFRC_5_CLK               |\
-			 PSDMR_PRETOACT_2W              |\
-			 PSDMR_ACTTORW_2W               |\
-			 PSDMR_LDOTOPRE_1C              |\
-			 PSDMR_WRC_1C                   |\
-			 PSDMR_CL_2)
-
-/*
- * GPIO/PIGGY on CS3 initialization values
- */
-#define CONFIG_SYS_PIGGY_BASE	0x30000000
-#define CONFIG_SYS_PIGGY_SIZE	128
-
-#define CONFIG_SYS_BR3_PRELIM	((CONFIG_SYS_PIGGY_BASE & BRx_BA_MSK) |\
-			 BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
-
-#define CONFIG_SYS_OR3_PRELIM	(MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) |\
-			 ORxG_CSNT | ORxG_ACS_DIV2 |\
-			 ORxG_SCY_3_CLK | ORxG_TRLX )
-
-/*
- * Board FPGA on CS4 initialization values
- */
-#define CONFIG_SYS_FPGA_BASE	0x40000000
-#define CONFIG_SYS_FPGA_SIZE	1 /*1KB*/
-
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_FPGA_BASE & BRx_BA_MSK) |\
-			BRx_PS_8 | BRx_MS_GPCM_P | BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FPGA_SIZE << 10) |\
-			 ORxG_CSNT | ORxG_ACS_DIV2 |\
-			 ORxG_SCY_3_CLK | ORxG_TRLX )
-
-/*
- * CFG-Flash on CS5 initialization values
- */
-#define CONFIG_SYS_BR5_PRELIM	((CONFIG_SYS_FLASH_BASE_1 & BRx_BA_MSK) |\
-			 BRx_PS_16 | BRx_MS_GPCM_P | BRx_V)
-
-#define CONFIG_SYS_OR5_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE_1 + \
-				 CONFIG_SYS_FLASH_SIZE_2) |\
-				 ORxG_CSNT | ORxG_ACS_DIV2 |\
-				 ORxG_SCY_5_CLK | ORxG_TRLX )
-
-#define	CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC	/* "bad" address */
-
-/* pass open firmware flat tree */
-#define CONFIG_FIT
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
-#define OF_TBCLK		(bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH		"/soc/cpm/serial at 11a90"
+/* include further common stuff for all keymile 82xx boards */
+#include "km82xx-common.h"
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/mgcoge2ne.h b/include/configs/mgcoge2ne.h
new file mode 100644
index 0000000..287b717
--- /dev/null
+++ b/include/configs/mgcoge2ne.h
@@ -0,0 +1,64 @@
+/*
+ * (C) Copyright 2007-2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __MGCOGE2NE
+#define __MGCOGE2NE
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC8247
+#define CONFIG_MGCOGE
+#define CONFIG_HOSTNAME		mgcoge2ne
+
+#define	CONFIG_SYS_TEXT_BASE	0xFE000000
+
+/* include common defines/options for all Keymile boards */
+#include "keymile-common.h"
+#include "km-powerpc.h"
+
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0xFE000000
+#define CONFIG_SYS_FLASH_SIZE		32
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_MAX_FLASH_BANKS	3	/* max num of flash banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	512	/*
+						 * max num of sects on one
+						 * chip
+						 */
+
+#define CONFIG_SYS_FLASH_BASE_1	0x50000000
+#define CONFIG_SYS_FLASH_SIZE_1	64
+#define CONFIG_SYS_FLASH_SIZE_2	0
+
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \
+					CONFIG_SYS_FLASH_BASE_1 }
+
+#define MTDIDS_DEFAULT		"nor2=app"
+
+/* include further common stuff for all keymile 82xx boards */
+#include "km82xx-common.h"
+
+#endif /* __MGCOGE2NE */
-- 
1.7.4



More information about the U-Boot mailing list