[U-Boot] [PATCH v3 8/8] arm/km: update mgcoge3un board support
Valentin Longchamp
valentin.longchamp at keymile.com
Wed May 4 17:53:50 CEST 2011
From: Holger Brunck <holger.brunck at keymile.com>
We change default settings for egiga on mgcoge3un.
The reason we need this is that we have the gig port on mgcoge3un
connected using a back-to-back pair of PHYs. There are no magnetics and
because of that the port has to be run with a fixd configuration and
auto-negotiation must be disabled. In the default mode the egiga driver
uses autoneg to determine port speed - which defaults to 1G (we need
100M full duplex).
Add wait for the GPIO line connected to mgcoge3ne before
starting mgcoge3un. A board specific ethernet present function
was added, because on this board ethernet is always present.
The BOCO FPGA access was enhanced and changed to use register
definitions.
Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
Acked-by: Heiko Schocher <hs at denx.de>
cc: Wolfgang Denk <wd at denx.de>
cc: Detlev Zundel <dzu at denx.de>
cc: Prafulla Wadaskar <prafulla at marvell.com>
---
Changes for v2:
- split up first large patch series to three independent smaller
patch series
Changes for v3:
- taken Prafulla's comments into account, merged with previous 08/08 patch
board/keymile/km_arm/km_arm.c | 80 +++++++++++++++++++++++++++++++++-------
include/configs/mgcoge3un.h | 25 +++++++++++++
2 files changed, 91 insertions(+), 14 deletions(-)
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 4049a4e..d86acc9 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -41,6 +41,16 @@
DECLARE_GLOBAL_DATA_PTR;
+/*
+ * BOCO FPGA definitions
+ */
+#define BOCO 0x10
+#define REG_CTRL_H 0x02
+#define MASK_WRL_UNITRUN 0x01
+#define MASK_RBX_PGY_PRESENT 0x40
+#define REG_IRQ_CIRQ2 0x2d
+#define MASK_RBI_DEFECT_16 0x01
+
/* Multi-Purpose Pins Functionality configuration */
u32 kwmpp_config[] = {
MPP0_NF_IO2,
@@ -102,43 +112,64 @@ u32 kwmpp_config[] = {
0
};
+#if defined(CONFIG_MGCOGE3UN)
+/*
+ * Wait for startup OK from mgcoge3ne
+ */
+int startup_allowed(void)
+{
+ unsigned char buf;
+
+ /*
+ * Read CIRQ16 bit (bit 0)
+ */
+ if (i2c_read(BOCO, REG_IRQ_CIRQ2, 1, &buf, 1) != 0)
+ printf("%s: Error reading Boco\n", __func__);
+ else
+ if ((buf & MASK_RBI_DEFECT_16) == MASK_RBI_DEFECT_16)
+ return 1;
+ return 0;
+}
+
+/*
+ * mgcoge3un has always ethernet present. Its connected to the 6061 switch
+ * and provides ICNev and piggy4 connections.
+ */
+int ethernet_present(void)
+{
+ return 1;
+}
+#else
int ethernet_present(void)
{
uchar buf;
int ret = 0;
- if (i2c_read(0x10, 2, 1, &buf, 1) != 0) {
+ if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
printf("%s: Error reading Boco\n", __func__);
return -1;
}
- if ((buf & 0x40) == 0x40)
+ if ((buf & MASK_RBX_PGY_PRESENT) == MASK_RBX_PGY_PRESENT)
ret = 1;
return ret;
}
+#endif
int initialize_unit_leds(void)
{
/*
- * init the unit LEDs
- * per default they all are
+ * Init the unit LEDs per default they all are
* ok apart from bootstat
- * LED connected through BOCO
- * BOCO lies at the address 0x10
- * LEDs are in the block CTRL_H (addr 0x02)
- * BOOTSTAT LED is the first 0x01
*/
- #define BOCO 0x10
- #define CTRL_H 0x02
- #define APPLEDMASK 0x01
uchar buf;
- if (i2c_read(BOCO, CTRL_H, 1, &buf, 1) != 0) {
+ if (i2c_read(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
printf("%s: Error reading Boco\n", __func__);
return -1;
}
- buf |= APPLEDMASK;
- if (i2c_write(BOCO, CTRL_H, 1, &buf, 1) != 0) {
+ buf |= MASK_WRL_UNITRUN;
+ if (i2c_write(BOCO, REG_CTRL_H, 1, &buf, 1) != 0) {
printf("%s: Error writing Boco\n", __func__);
return -1;
}
@@ -167,6 +198,27 @@ int misc_init_r(void)
printf("Overwriting MACH_TYPE with %d!!!\n", mach_type);
gd->bd->bi_arch_number = mach_type;
}
+#if defined(CONFIG_MGCOGE3UN)
+ char *wait_for_ne;
+ wait_for_ne = getenv("waitforne");
+ if (wait_for_ne != NULL) {
+ if (strcmp(wait_for_ne, "true") == 0) {
+ int cnt = 0;
+ puts("NE go: ");
+ while (startup_allowed() == 0) {
+ udelay(200000);
+ cnt++;
+ if (cnt == 5)
+ puts("wait\b\b\b\b");
+ if (cnt == 10) {
+ cnt = 0;
+ puts(" \b\b\b\b");
+ }
+ }
+ puts("OK\n");
+ }
+ }
+#endif
initialize_unit_leds();
set_km_env();
diff --git a/include/configs/mgcoge3un.h b/include/configs/mgcoge3un.h
index 1c32085..d022c4f 100644
--- a/include/configs/mgcoge3un.h
+++ b/include/configs/mgcoge3un.h
@@ -50,4 +50,29 @@
/* we use a new RAM type on mgcoge3un board */
#define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-memphis.cfg
+/*
+ * mgcoge3un has a fixed link to the marvell switch
+ * with 100MB full duplex and autoneg off, for this
+ * reason we have to change the default settings
+ */
+#define PORT_SERIAL_CONTROL_VALUE ( \
+ MVGBE_FORCE_LINK_PASS | \
+ MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \
+ MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \
+ MVGBE_ADV_NO_FLOW_CTRL | \
+ MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \
+ MVGBE_FORCE_BP_MODE_NO_JAM | \
+ (1 << 9) /* Reserved bit has to be 1 */ | \
+ MVGBE_DO_NOT_FORCE_LINK_FAIL | \
+ MVGBE_DIS_AUTO_NEG_SPEED_GMII | \
+ MVGBE_DTE_ADV_0 | \
+ MVGBE_MIIPHY_MAC_MODE | \
+ MVGBE_AUTO_NEG_NO_CHANGE | \
+ MVGBE_MAX_RX_PACKET_1552BYTE | \
+ MVGBE_CLR_EXT_LOOPBACK | \
+ MVGBE_SET_FULL_DUPLEX_MODE | \
+ MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\
+ MVGBE_SET_GMII_SPEED_TO_10_100 |\
+ MVGBE_SET_MII_SPEED_TO_100)
+
#endif /* _CONFIG_MGCOGE3UN_H */
--
1.7.0.5
More information about the U-Boot
mailing list