[U-Boot] [PATCH] qoriq/p1_p2_rdb: USB device-tree fixups for P1020

Wolfgang Denk wd at denx.de
Tue May 10 15:44:22 CEST 2011


Dear Ramneek Mehresh,

In message <1305032211-7732-1-git-send-email-ramneek.mehresh at freescale.com> you wrote:
> Resolve P1020 second USB controller multiplexing with eLBC
> 	- mandatory to mention USB2 in hwconfig string to select it
> 	  over eLBC, otherwise USB2 node is removed
> 	- works only for SPI and SD boot
> 
> Signed-off-by: Ramneek Mehresh <ramneek.mehresh at freescale.com>
> ---
> Applies on git://git.am.freescale.net/mirrors/u-boot.git
> (branch master)

Forget it.   It is a mandatory requirement that patches are submitted
against the master branch of the master repository.

NAK, without even looking further.


>  board/freescale/p1_p2_rdb/p1_p2_rdb.c |   54 +++++++++++++++++++++++++++++++++
>  1 files changed, 54 insertions(+), 0 deletions(-)
> 
> diff --git a/board/freescale/p1_p2_rdb/p1_p2_rdb.c b/board/freescale/p1_p2_rdb/p1_p2_rdb.c
> index d66b130..14ad895 100644
> --- a/board/freescale/p1_p2_rdb/p1_p2_rdb.c
> +++ b/board/freescale/p1_p2_rdb/p1_p2_rdb.c
> @@ -37,6 +37,7 @@
>  #include <netdev.h>
>  #include <rtc.h>
>  #include <i2c.h>
> +#include <hwconfig.h>
>  
>  DECLARE_GLOBAL_DATA_PTR;
>  
> @@ -247,6 +248,11 @@ extern void ft_pci_board_setup(void *blob);
>  
>  void ft_board_setup(void *blob, bd_t *bd)
>  {
> +#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
> +	const char *soc_elbc_compat = "fsl,p1020-elbc";
> +#endif
> +	const char *soc_usb_compat = "fsl-usb2-dr";
> +	int off, err, usb1_off, usb2_off;
>  	phys_addr_t base;
>  	phys_size_t size;
>  
> @@ -260,5 +266,53 @@ void ft_board_setup(void *blob, bd_t *bd)
>  #endif /* #if defined(CONFIG_PCI) */
>  
>  	fdt_fixup_memory(blob, (u64)base, (u64)size);
> +
> +	fdt_fixup_dr_usb(blob, bd);
> +
> +#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
> +	/* Delete eLBC node as it is muxed with USB2 controller */
> +	if (hwconfig("usb2")) {
> +		off = fdt_node_offset_by_compatible(blob, -1,
> +			soc_elbc_compat);
> +		if (off < 0) {
> +			printf("WARNING: could not find compatible node"
> +				" %s: %s.\n", soc_elbc_compat,
> +				fdt_strerror(off));
> +				return;
> +		}
> +		err = fdt_del_node(blob, off);
> +		if (err < 0) {
> +			printf("WARNING: could not remove %s: %s.\n",
> +				soc_elbc_compat, fdt_strerror(err));
> +				return;
> +		}

Move the return; from oneline above here.

> +	} else {
> +#endif

Then you can get rid of this "else {" part, and indentation will
become correct.  As is, it's ugly at best.

> +		/* Delete USB2 node as it is muxed with eLBC */
> +		usb1_off = fdt_node_offset_by_compatible(blob, -1,
> +			soc_usb_compat);
> +		if (usb1_off < 0) {
> +			printf("WARNING: could not find compatible node"
> +				" %s: %s.\n", soc_usb_compat,
> +				fdt_strerror(usb1_off));
> +			return;
> +		}
> +		usb2_off = fdt_node_offset_by_compatible(blob, usb1_off,
> +				 soc_usb_compat);
> +		if (usb2_off < 0) {
> +			printf("WARNING: could not find compatible node"
> +				" %s: %s.\n", soc_usb_compat,
> +				fdt_strerror(usb2_off));
> +			return;
> +		}
> +		err = fdt_del_node(blob, usb2_off);
> +		if (err < 0) {
> +			printf("WARNING: could not remove %s: %s.\n",
> +				soc_usb_compat, fdt_strerror(err));
> +			return;
> +		}
> +#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
> +	}
> +#endif

This #if will then disappear, too.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
A committee is a life form with six or more legs and no brain.
                              -- Lazarus Long, "Time Enough For Love"


More information about the U-Boot mailing list