[U-Boot] [PATCH] mx51evk: Make use of the i.MX GPIO API

Fabio Estevam fabio.estevam at freescale.com
Thu May 19 21:15:22 CEST 2011


Make use of the i.MX GPIO API.

While at it created a separate function for the FEC PHY reset,
so that it can be decoupled from the power_init function.

Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
---
 board/freescale/mx51evk/mx51evk.c |   33 +++++++++++++++++----------------
 1 files changed, 17 insertions(+), 16 deletions(-)

diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c
index ef7c6e4..2dabef9 100644
--- a/board/freescale/mx51evk/mx51evk.c
+++ b/board/freescale/mx51evk/mx51evk.c
@@ -33,6 +33,11 @@
 #include <fsl_esdhc.h>
 #include <fsl_pmic.h>
 #include <mc13892.h>
+#include <mxc_gpio.h>
+
+#define MX51EVK_PHY_RESET	(1 * 32 + 14)	/* GPIO2_14 */
+#define MX51EVK_SD1_CD		(0 * 32 + 0)	/* GPIO1_0 */
+#define MX51EVK_SD2_CD		(0 * 32 + 6)	/* GPIO1_6 */
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -261,27 +266,22 @@ static void power_init(void)
 	pmic_reg_write(REG_MODE_1, val);
 	udelay(200);
 
-	reg = readl(GPIO2_BASE_ADDR + 0x0);
-	reg &= ~0x4000;  /* Lower reset line */
-	writel(reg, GPIO2_BASE_ADDR + 0x0);
-
-	reg = readl(GPIO2_BASE_ADDR + 0x4);
-	reg |= 0x4000;	/* configure GPIO lines as output */
-	writel(reg, GPIO2_BASE_ADDR + 0x4);
-
-	/* Reset the ethernet controller over GPIO */
-	writel(0x1, IOMUXC_BASE_ADDR + 0x0AC);
-
 	/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
 	val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
 		VVIDEOEN | VAUDIOEN  | VSDEN;
 	pmic_reg_write(REG_MODE_1, val);
+}
+
+static void reset_phy_fec(void)
+{
+	mxc_request_iomux(MX51_PIN_EIM_A20, IOMUX_CONFIG_ALT1);
+	mxc_gpio_direction(MX51EVK_PHY_RESET, MXC_GPIO_DIRECTION_OUT);
 
+	mxc_gpio_set(MX51EVK_PHY_RESET, 0);	/* Lower reset line */
+
 	udelay(500);
 
-	reg = readl(GPIO2_BASE_ADDR + 0x0);
-	reg |= 0x4000;
-	writel(reg, GPIO2_BASE_ADDR + 0x0);
+	mxc_gpio_set(MX51EVK_PHY_RESET, 1);	/* Set reset line to high */
 }
 
 #ifdef CONFIG_FSL_ESDHC
@@ -290,9 +290,9 @@ int board_mmc_getcd(u8 *cd, struct mmc *mmc)
 	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 
 	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
-		*cd = readl(GPIO1_BASE_ADDR) & 0x01;
+		*cd = mxc_gpio_get(MX51EVK_SD1_CD);
 	else
-		*cd = readl(GPIO1_BASE_ADDR) & 0x40;
+		*cd = mxc_gpio_get(MX51EVK_SD2_CD);
 
 	return 0;
 }
@@ -414,6 +414,7 @@ int board_mmc_init(bd_t *bis)
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
+	reset_phy_fec();
 	setup_iomux_fec();
 
 	return 0;
-- 
1.6.0.4




More information about the U-Boot mailing list