[U-Boot] [PATCH] ulpi: add generic ULPI support header file
Marek Vasut
marek.vasut at gmail.com
Wed Nov 2 11:24:34 CET 2011
Hi Igor,
> Hi Jana,
>
> On 11/01/11 21:12, Jana Rapava wrote:
> > Add ULPI header file needed by Efika USB support patchset and generic
> > ULPI support patch, which is to be posted soon.
> >
> > Signed-off-by: Jana Rapava <fermata7 at gmail.com>
> > Cc: Marek Vasut <marek.vasut at gmail.com>
> > Cc: Remy Bohmer <linux at bohmer.net>
> > Cc: Stefano Babic <sbabic at denx.de>
> > Cc: Igor Grinberg <grinberg at compulab.co.il>
> > ---
> >
> > include/usb/ulpi.h | 195
> > ++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 files changed,
> > 195 insertions(+), 0 deletions(-)
> > create mode 100644 include/usb/ulpi.h
> >
> > diff --git a/include/usb/ulpi.h b/include/usb/ulpi.h
> > new file mode 100644
> > index 0000000..4a88b5f
> > --- /dev/null
> > +++ b/include/usb/ulpi.h
> > @@ -0,0 +1,195 @@
> > +/*
> > + * Copyright (C) 2011 Jana Rapava <fermata7 at gmail.com>
> > + * Based on:
> > + * linux/include/linux/usb/ulpi.h
> > + * ULPI defines and function prototypes
> > + *
> > + * Original Copyrights follow:
> > + * Copyright (C) 2010 Nokia Corporation
> > + *
> > + * This software is distributed under the terms of the GNU General
> > + * Public License ("GPL") as published by the Free Software Foundation,
> > + * version 2 of that License.
> > + */
> > +
> > +#ifndef __USB_ULPI_H
> > +#define __USB_ULPI_H
> > +
> > +#define ULPI_ID_REGS_COUNT 4
> > +#define ULPI_TEST_VALUE 0x55
> > +#define ULPI_TIMEOUT 1000 /* some reasonable value */
> > +
> > +/* ULPI viewport control bits */
> > +#define ULPI_WU (1 << 31)
> > +#define ULPI_SS (1 << 27)
> > +#define ULPI_RWRUN (1 << 30)
> > +#define ULPI_RWCTRL (1 << 29)
> > +
> > +struct ulpi_regs {
> > + u8 vendor_id_low; /* 0x00 - Vendor ID lower byte */
> > + u8 vendor_id_high; /* 0x01 - Vendor ID upper byte */
> > + u8 product_id_low; /* 0x02 - Product ID lower byte */
> > + u8 product_id_high; /* 0x03 - Product ID higher byte */
> > + /* Function Control; 0x04 - 0x06 Read, 0x04 Write */
> > + u8 function_ctrl_write;
> > + u8 function_ctrl_set; /* 0x05 Set */
> > + u8 function_ctrl_clear; /* 0x06 Clear */
> > + /* Interface Control; 0x07 - 0x09 Read, 0x07 Write */
> > + u8 iface_ctrl_write;
> > + u8 iface_ctrl_set; /* 0x08 Set */
> > + u8 iface_ctrl_clear; /* 0x09 Clear */
> > + /* OTG Control; 0x0A - 0x0C Read, 0x0A Write */
> > + u8 otg_ctrl_write;
> > + u8 otg_ctrl_set; /* 0x0B Set */
> > + u8 otg_ctrl_clear; /* 0x0C Clear */
> > + /* USB Interrupt Enable Rising; 0x0D - 0x0F Read, 0x0D Write */
> > + u8 usb_ie_rising_write;
> > + u8 usb_ie_rising_set; /* 0x0E Set */
> > + u8 usb_ie_rising_clear; /* 0x0F Clear */
> > + /* USB Interrupt Enable Falling; 0x10 - 0x12 Read, 0x10 Write */
> > + u8 usb_ie_falling_write;
> > + u8 usb_ie_falling_set; /* 0x11 Set */
> > + u8 usb_ie_falling_clear; /* 0x12 Clear */
> > + u8 usb_int_status; /* 0x13 - USB Interrupt Status */
> > + u8 usb_int_latch; /* 0x14 - USB Interrupt Latch */
> > + u8 debug; /* 0x15 - Debug */
> > + /* Scratch Register; 0x16 - 0x18 Read, 0x16 Write */
> > + u8 scratch_write;
> > + u8 scratch_set; /* 0x17 Set */
> > + u8 scratch_clear; /* 0x18 Clear */
> > + /*
> > + * Optional Carkit registers
> > + */
> > + /* Carkit Control; 0x19 - 0x1B Read, 0x19 Write */
> > + u8 carkit_ctrl_write;
> > + u8 carkit_ctrl_set;
> > + u8 carkit_ctrl_clear;
> > + /* Carkit Interrupt Delay */
> > + u8 carkit_int_delay; /* 0x1C Read, Write */
> > + /* Carkit Interrupt Enable; 0x1D - 0x1F Read, 0x1D Write */
> > + u8 carkit_ie_write;
> > + u8 carkit_ie_set;
> > + u8 carkit_ie_clear;
> > + u8 carkit_int_status; /* 0x20 - Carkit Interrupt Status */
> > + u8 carkit_int_latch; /* 0x21 - Carkit Interrupt Latch */
> > + /* Carkit Pulse Control; 0x22 - 0x24 Read, 0x22 Write */
> > + u8 carkit_pulse_ctrl_write;
> > + u8 carkit_pulse_ctrl_set;
> > + u8 carkit_pulse_ctrl_clear;
> > + /*
> > + * Other optional registers
> > + */
> > + u8 transmit_pos_width; /* 0x25 - Transmit Positive Width */
> > + u8 transmit_neg_width; /* 0x26 - Transmit Negative Width */
> > + u8 recv_pol_recovery; /* 0x27 - Receive Polarity Recovery */
> > + /*
> > + * Addresses 0x28 - 0x2E are reserved, so we use offsets
> > + * for immediate registers with higher addresses
> > + */
> > +};
>
> In the structure above, you have a mixture of tab and spaces
> after the type before the name.
> You can use either tabs or spaces (I prefer spaces), but not both.
I prefer tabs, they improve readability and it's easier to navigate in the file
;-) Anyway, I agree that not both shall be used.
>
> > +
> > +/* Access Extended Register Set (indicator) */
> > +#define ACCESS_EXT_REGS_OFFSET 0x2f /* read-write */
> > +/* Vendor-specific */
> > +#define VENDOR_SPEC_OFFSET 0x30
> > +
> > +/*
> > + * Extended Register Set
> > + *
> > + * Addresses 0x00-0x3F map directly to Immediate Register Set.
> > + * Addresses 0x40-0x7F are reserved.
> > + * Addresses 0x80-0xff are vendor-specific.
> > + */
> > +#define EXT_VENDOR_SPEC_OFFSET 0x80
> > +
> > +/*
> > + * Register Bits
> > + */
> > +
> > +/* Function Control */
> > +#define ULPI_FC_XCVRSEL (1 << 0)
> > +#define ULPI_FC_XCVRSEL_MASK (3 << 0)
> > +#define ULPI_FC_HIGH_SPEED (0 << 0)
> > +#define ULPI_FC_FULL_SPEED (1 << 0)
> > +#define ULPI_FC_LOW_SPEED (2 << 0)
> > +#define ULPI_FC_FS4LS (3 << 0)
> > +#define ULPI_FC_TERMSELECT (1 << 2)
> > +#define ULPI_FC_OPMODE (1 << 3)
> > +#define ULPI_FC_OPMODE_MASK (3 << 3)
> > +#define ULPI_FC_OPMODE_NORMAL (0 << 3)
> > +#define ULPI_FC_OPMODE_NONDRIVING (1 << 3)
> > +#define ULPI_FC_OPMODE_DISABLE_NRZI (2 << 3)
> > +#define ULPI_FC_OPMODE_NOSYNC_NOEOP (3 << 3)
> > +#define ULPI_FC_RESET (1 << 5)
> > +#define ULPI_FC_SUSPENDM (1 << 6)
> > +
> > +/* Interface Control */
> > +#define ULPI_IFACE_6_PIN_SERIAL_MODE (1 << 0)
> > +#define ULPI_IFACE_3_PIN_SERIAL_MODE (1 << 1)
> > +#define ULPI_IFACE_CARKITMODE (1 << 2)
> > +#define ULPI_IFACE_CLOCKSUSPENDM (1 << 3)
> > +#define ULPI_IFACE_AUTORESUME (1 << 4)
> > +#define ULPI_IFACE_EXTVBUS_COMPLEMENT (1 << 5)
> > +#define ULPI_IFACE_PASSTHRU (1 << 6)
> > +#define ULPI_IFACE_PROTECT_IFC_DISABLE (1 << 7)
> > +
> > +/* OTG Control */
> > +#define ULPI_OTG_ID_PULLUP (1 << 0)
> > +#define ULPI_OTG_DP_PULLDOWN (1 << 1)
> > +#define ULPI_OTG_DM_PULLDOWN (1 << 2)
> > +#define ULPI_OTG_DISCHRGVBUS (1 << 3)
> > +#define ULPI_OTG_CHRGVBUS (1 << 4)
> > +#define ULPI_OTG_DRVVBUS (1 << 5)
> > +#define ULPI_OTG_DRVVBUS_EXT (1 << 6)
> > +#define ULPI_OTG_EXTVBUSIND (1 << 7)
> > +
> > +/*
> > + * USB Interrupt Enable Rising,
> > + * USB Interrupt Enable Falling,
> > + * USB Interrupt Status and
> > + * USB Interrupt Latch
> > + */
> > +#define ULPI_INT_HOST_DISCONNECT (1 << 0)
> > +#define ULPI_INT_VBUS_VALID (1 << 1)
> > +#define ULPI_INT_SESS_VALID (1 << 2)
> > +#define ULPI_INT_SESS_END (1 << 3)
> > +#define ULPI_INT_IDGRD (1 << 4)
> > +
> > +/* Debug */
> > +#define ULPI_DEBUG_LINESTATE0 (1 << 0)
> > +#define ULPI_DEBUG_LINESTATE1 (1 << 1)
> > +
> > +/* Carkit Control */
> > +#define ULPI_CARKIT_CTRL_CARKITPWR (1 << 0)
> > +#define ULPI_CARKIT_CTRL_IDGNDDRV (1 << 1)
> > +#define ULPI_CARKIT_CTRL_TXDEN (1 << 2)
> > +#define ULPI_CARKIT_CTRL_RXDEN (1 << 3)
> > +#define ULPI_CARKIT_CTRL_SPKLEFTEN (1 << 4)
> > +#define ULPI_CARKIT_CTRL_SPKRIGHTEN (1 << 5)
> > +#define ULPI_CARKIT_CTRL_MICEN (1 << 6)
> > +
> > +/* Carkit Interrupt Enable */
> > +#define ULPI_CARKIT_INT_EN_IDFLOAT_RISE (1 << 0)
> > +#define ULPI_CARKIT_INT_EN_IDFLOAT_FALL (1 << 1)
> > +#define ULPI_CARKIT_INT_EN_CARINTDET (1 << 2)
> > +#define ULPI_CARKIT_INT_EN_DP_RISE (1 << 3)
> > +#define ULPI_CARKIT_INT_EN_DP_FALL (1 << 4)
> > +
> > +/*
> > + * Carkit Interrupt Status and
> > + * Carkit Interrupt Latch
> > + */
> > +#define ULPI_CARKIT_INT_IDFLOAT (1 << 0)
> > +#define ULPI_CARKIT_INT_CARINTDET (1 << 1)
> > +#define ULPI_CARKIT_INT_DP (1 << 2)
> > +
> > +/* Carkit Pulse Control*/
> > +#define ULPI_CARKIT_PLS_CTRL_TXPLSEN (1 << 0)
> > +#define ULPI_CARKIT_PLS_CTRL_RXPLSEN (1 << 1)
> > +#define ULPI_CARKIT_PLS_CTRL_SPKRLEFT_BIASEN (1 << 2)
> > +#define ULPI_CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN (1 << 3)
> > +
> > +void ulpi_write(struct usb_ehci *ehci, u32 reg, u32 value);
> > +u32 ulpi_read(struct usb_ehci *ehci, u32 reg);
> > +
> > +#endif /* __USB_ULPI_H */
More information about the U-Boot
mailing list