[U-Boot] [PATCH v3 2/2] mpc85xx: support for Freescale COM Express P2020
Ira W. Snyder
iws at ovro.caltech.edu
Sat Nov 12 00:33:29 CET 2011
On Fri, Nov 11, 2011 at 03:10:43PM -0800, Ira W. Snyder wrote:
> On Fri, Nov 11, 2011 at 03:02:46PM -0800, York Sun wrote:
> > Looking good so far, what's the question? You can always override the
> > register values and try it since you got the interactive debug up.
> >
>
> Well, it doesn't work out of the box.
>
> I'm very worried about the following messages:
> > unknown module_type 0x08
> > Detected UDIMM SG572568EMR069S2SF
> > The choosen cas latency 16 is too large
>
> I copied the settings from the configuration for the On-Chip ROM's RAM
> setup. I issued the following in the interactive DDR setup:
>
> FSL-DDR> compute
> FSL-DDR> edit c0 d0 regs ddr_sdram_cfg e7000008
> ... lots more ...
> FSL-DDR> go
>
> That didn't work. Maybe I did something wrong? I'll try again.
I tried again. It turns out "edit" values have to be prefixed by "0x"
for hex values (unlike the rest of U-Boot).
The commands I used. You can double check that they match the
config_sram_blackadder2020.dat posted earlier in this thread.
edit c0 d0 regs ddr_sdram_cfg 0x67000008
edit c0 d0 regs cs0_bnds 0x0000003f
edit c0 d0 regs cs1_bnds 0x0040007f
edit c0 d0 regs cs0_config 0x80014202
edit c0 d0 regs cs1_config 0x80014202
edit c0 d0 regs timing_cfg_0 0x00330804
edit c0 d0 regs timing_cfg_1 0x6f6b4644
edit c0 d0 regs timing_cfg_2 0x0fa890d0
edit c0 d0 regs timing_cfg_3 0x00020000
edit c0 d0 regs ddr_sdram_cfg_2 0x24400010
edit c0 d0 regs ddr_sdram_mode 0x00401422
edit c0 d0 regs ddr_sdram_interval 0x61800100
edit c0 d0 regs ddr_data_init 0xdeadbeef
edit c0 d0 regs ddr_sdram_clk_cntl 0x02800000
edit c0 d0 regs timing_cfg_4 0x00220001
edit c0 d0 regs timing_cfg_5 0x03402400
edit c0 d0 regs ddr_zq_cntl 0x89080600
edit c0 d0 regs ddr_wrlvl_cntl 0x8655a608
edit c0 d0 regs err_int_en 0x0000000d
edit c0 d0 regs ddr_cdr1 0x000c0000
edit c0 d0 regs ddr_cdr2 0x00000000
edit c0 d0 regs ddr_sdram_cfg 0xe7000008
go
I get this message:
2 GiB (DDR2, 64-bit, CL=0.5, ECC off)
Basically completely wrong. It should be DDR3, CL=6, ECC on. That's what
happened before I tried to use the SPD.
I could use some pointers on how to debug this.
Ira
> > On Fri, 2011-11-11 at 14:54 -0800, McClintock Matthew-B29882 wrote:
> > > Adding York who might be able to help more...
> > >
> > > -M
> > >
> > > On Fri, Nov 11, 2011 at 4:18 PM, Ira W. Snyder <iws at ovro.caltech.edu> wrote:
> > > > On Fri, Nov 11, 2011 at 09:07:23PM +0000, McClintock Matthew-B29882 wrote:
> > > >> On Fri, Nov 11, 2011 at 3:03 PM, Ira W. Snyder <iws at ovro.caltech.edu> wrote:
> > > >> > Thanks. That config_sram.dat is exactly what I came up with.
> > > >> >
> > > >> > I have my board booting via L2SRAM, but the DDR doesn't get configured
> > > >> > correctly yet. I'm trying to figure out how the DDR SPD stuff works in
> > > >> > U-Boot. I've never used it before. I'm following the P2020DS code as an
> > > >> > example, but I haven't yet figured out how the code in
> > > >> > board/freescale/p2020ds/ddr.c was derived (the board_specific_parameters
> > > >> > structure especially).
> > > >>
> > > >> If you board has i2c to the ddr modules it should be able to use the
> > > >> timing info from there. I think CONFIG_DDR_SPD is the config option
> > > >> you are looking for. I know the P2020DS does SPD from L2SRAM.
> > > >>
> > > >
> > > > The only thing that looks like an SPD chip is at i2c bus 1, address
> > > > 0x53. I setup my board configuration with:
> > > >
> > > > #define CONFIG_FSL_DDR3
> > > > #define CONFIG_FSL_DDR_INTERACTIVE
> > > > #define CONFIG_CHIP_SELECTS_PER_CTRL 2
> > > > #define CONFIG_SYS_DDR_SBE 0x00010000
> > > >
> > > > #define CONFIG_DDR_SPD
> > > > #define CONFIG_SYS_SPD_BUS_NUM 1
> > > > #define SPD_EEPROM_ADDRESS 0x53
> > > >
> > > > Some of the settings the SPD code computes are correct, and some are
> > > > completely wrong. I can't figure out how to make this work.
> > > >
> > > > Here is the raw SPD dumped from a working U-Boot:
> > > >
> > > > 0000: 92 10 0b 08 02 11 00 09 0b 52 01 08 0c 00 3e 00 .........R....>.
> > > > 0010: 69 78 69 30 69 11 20 89 70 03 3c 3c 00 f0 83 05 ixi0i. .p.<<....
> > > > 0020: 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > > 0030: 00 00 00 00 00 00 00 00 00 00 00 00 0f 11 1f 00 ................
> > > > 0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > > 0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > > 0060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > > 0070: 00 00 00 00 00 01 94 01 10 25 03 ae 48 48 e3 e3 .........%..HH..
> > > > 0080: 53 47 35 37 32 35 36 38 45 4d 52 30 36 39 53 32 SG572568EMR069S2
> > > > 0090: 53 46 00 00 80 ce 53 4d 41 52 54 4d 6f 64 75 6c SF....SMARTModul
> > > > 00a0: 61 72 54 65 63 68 6e 6f 6c 6f 67 69 65 73 00 00 arTechnologies..
> > > > 00b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > > 00c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > > 00d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > > 00e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > > 00f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> > > >
> > > > And here is the output of an interactive FSL DDR run:
> > > >
> > > > U-Boot 2011.09-00929-g3b5f71c-dirty (Nov 11 2011 - 13:31:13)
> > > >
> > > > CPU0: P2020E, Version: 2.0, (0x80ea0020)
> > > > Core: E500, Version: 5.0, (0x80211050)
> > > > Clock Configuration:
> > > > CPU0:1200 MHz, CPU1:1200 MHz,
> > > > CCB:600 MHz,
> > > > DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:37.500 MHz
> > > > L1: D-cache 32 kB enabled
> > > > I-cache 32 kB enabled
> > > > Board: Freescale COM Express P2020
> > > > I2C: ready
> > > > SPI: ready
> > > > DRAM: FSL DDR>
> > > > FSL DDR>
> > > > FSL DDR>compute
> > > > unknown module_type 0x08
> > > > Detected UDIMM SG572568EMR069S2SF
> > > > The choosen cas latency 16 is too large
> > > > FSL DDR>print c0 d0
> > > > SPD info: Controller=0 DIMM=0
> > > > 0 : 92 info_size_crc bytes written into serial memory, CRC coverage
> > > > 1 : 10 spd_rev SPD Revision
> > > > 2 : 0b mem_type Key Byte / DRAM Device Type
> > > > 3 : 08 module_type Key Byte / Module Type
> > > > 4 : 02 density_banks SDRAM Density and Banks
> > > > 5 : 11 addressing SDRAM Addressing
> > > > 6 : 00 module_vdd Module Nominal Voltage, VDD
> > > > 7 : 09 organization Module Organization
> > > > 8 : 0b bus_width Module Memory Bus Width
> > > > 9 : 52 ftb_div Fine Timebase (FTB) Dividend / Divisor
> > > > 10 : 01 mtb_dividend Medium Timebase (MTB) Dividend
> > > > 11 : 08 mtb_divisor Medium Timebase (MTB) Divisor
> > > > 12 : 0c tCK_min SDRAM Minimum Cycle Time
> > > > 13 : 00 res_13 Reserved
> > > > 14 : 3e caslat_lsb CAS Latencies Supported, LSB
> > > > 15 : 00 caslat_msb CAS Latencies Supported, MSB
> > > > 16 : 69 tAA_min Min CAS Latency Time
> > > > 17 : 78 tWR_min Min Write REcovery Time
> > > > 18 : 69 tRCD_min Min RAS# to CAS# Delay Time
> > > > 19 : 30 tRRD_min Min Row Active to Row Active Delay Time
> > > > 20 : 69 tRP_min Min Row Precharge Delay Time
> > > > 21 : 11 tRAS_tRC_ext Upper Nibbles for tRAS and tRC
> > > > 22 : 20 tRAS_min_lsb Min Active to Precharge Delay Time, LSB
> > > > 23 : 89 tRC_min_lsb Min Active to Active/Refresh Delay Time, LSB
> > > > 24 : 70 tRFC_min_lsb Min Refresh Recovery Delay Time LSB
> > > > 25 : 03 tRFC_min_msb Min Refresh Recovery Delay Time MSB
> > > > 26 : 3c tWTR_min Min Internal Write to Read Command Delay Time
> > > > 27 : 3c tRTP_min Min Internal Read to Precharge Command Delay Time
> > > > 28 : 00 tFAW_msb Upper Nibble for tFAW
> > > > 29 : f0 tFAW_min Min Four Activate Window Delay Time
> > > > 30 : 83 opt_features SDRAM Optional Features
> > > > 31 : 05 therm_ref_opt SDRAM Thermal and Refresh Opts
> > > > 32 : 80 therm_sensor SDRAM Thermal Sensor
> > > > 33 : 00 device_type SDRAM Device Type
> > > > 34 - 59: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> > > > 60 -116: 0f111f000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000117 : 01 Module MfgID Code LSB - JEP-106
> > > > 118 : 94 Module MfgID Code MSB - JEP-106
> > > > 119 : 01 Mfg Location
> > > > 120-121: 10 25 Mfg Date
> > > > 122-125: 03 ae 48 48 Module Serial Number
> > > > 126-127: e3 e3 SPD CRC
> > > > 128-145: 53 47 35 37 32 35 36 38 45 4d 52 30 36 39 53 32 53 46 Mfg's Module Part Number
> > > > 146-147: 00 00 Module Revision code
> > > > 148 : 80 DRAM MfgID Code LSB - JEP-106
> > > > 149 : ce DRAM MfgID Code MSB - JEP-106
> > > > 150-175: 53 4d 41 52 54 4d 6f 64 75 6c 61 72 54 65 63 68 6e 6f 6c 6f 67 69 65 73 00 00 Mfg's Specific Data
> > > > 176-255: 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 Mfg's Specific Data
> > > >
> > > >
> > > >
> > > > DIMM parameters: Controller=0 DIMM=0
> > > > DIMM organization parameters:
> > > > module part name = SG572568EMR069S2SF
> > > > rank_density = 1073741824 bytes (1024 megabytes)
> > > > capacity = 2147483648 bytes (2048 megabytes)
> > > > burst_lengths_bitmask = 00
> > > > base_addresss = 0 (00000000 00000000)
> > > > n_ranks = 2
> > > > data_width = 72
> > > > primary_sdram_width = 64
> > > > ec_sdram_width = 8
> > > > registered_dimm = 0
> > > > n_row_addr = 0
> > > > n_col_addr = 0
> > > > edc_config = 0
> > > > n_banks_per_sdram_device = 0
> > > > tCKmin_X_ps = 0
> > > > tCKmin_X_minus_1_ps = 0
> > > > tCKmin_X_minus_2_ps = 0
> > > > tCKmax_ps = 0
> > > > caslat_X = 0
> > > > tAA_ps = 0
> > > > caslat_X_minus_1 = 0
> > > > caslat_X_minus_2 = 0
> > > > caslat_lowest_derated = 0
> > > > tRCD_ps = 0
> > > > tRP_ps = 0
> > > > tRAS_ps = 0
> > > > tWR_ps = 0
> > > > tWTR_ps = 0
> > > > tRFC_ps = 0
> > > > tRRD_ps = 0
> > > > tRC_ps = 0
> > > > refresh_rate_ps = 0
> > > > tIS_ps = 0
> > > > tIH_ps = 0
> > > > tDS_ps = 0
> > > > tDH_ps = 0
> > > > tRTP_ps = 0
> > > > tDQSQ_max_ps = 0
> > > > tQHS_ps = 0
> > > >
> > > >
> > > >
> > > > "lowest common" DIMM parameters: Controller=0
> > > > tCKmin_X_ps = 0 (4294967295 MHz)
> > > > tCKmax_ps = 0 (4294967295 MHz)
> > > > all_DIMMs_burst_lengths_bitmask = 00
> > > > tCKmax_max_ps = 0
> > > > tRCD_ps = 0
> > > > tRP_ps = 0
> > > > tRAS_ps = 0
> > > > tWR_ps = 0
> > > > tWTR_ps = 0
> > > > tRFC_ps = 0
> > > > tRRD_ps = 0
> > > > tRC_ps = 0
> > > > refresh_rate_ps = 0
> > > > tIS_ps = 0
> > > > tDS_ps = 0
> > > > tDH_ps = 0
> > > > tRTP_ps = 0
> > > > tDQSQ_max_ps = 0
> > > > tQHS_ps = 0
> > > > lowest_common_SPD_caslat = 0
> > > > highest_common_derated_caslat = 0
> > > > additive_latency = 0
> > > > ndimms_present = 1
> > > > all_DIMMs_registered = 0
> > > > all_DIMMs_unbuffered = 1
> > > > all_DIMMs_ECC_capable = 0
> > > > total_mem = 2147483648 (2048 megabytes)
> > > > base_address = 0 (0 megabytes)
> > > >
> > > >
> > > > User Config Options: Controller=0
> > > > cs0_odt_rd_cfg = 0
> > > > cs0_odt_wr_cfg = 1
> > > > cs1_odt_rd_cfg = 0
> > > > cs1_odt_wr_cfg = 1
> > > > cs0_odt_rtt_norm = 3
> > > > cs0_odt_rtt_wr = 0
> > > > cs1_odt_rtt_norm = 0
> > > > cs1_odt_rtt_wr = 0
> > > > memctl_interleaving = 0
> > > > memctl_interleaving_mode = 0
> > > > ba_intlv_ctl = 0x00000040
> > > > ECC_mode = 0
> > > > ECC_init_using_memctl = 1
> > > > DQS_config = 1
> > > > self_refresh_in_sleep = 1
> > > > dynamic_power = 0
> > > > data_bus_width = 0
> > > > burst_length = 6
> > > > cas_latency_override = 0
> > > > cas_latency_override_value = 3
> > > > use_derated_caslat = 0
> > > > additive_latency_override = 0
> > > > additive_latency_override_value = 3
> > > > clk_adjust = 6
> > > > cpo_override = 31
> > > > write_data_delay = 4
> > > > half_strength_driver_enable = 0
> > > > twoT_en = 0
> > > > threeT_en = 0
> > > > registered_dimm_en = 0
> > > > ap_en = 1
> > > > bstopre = 256
> > > > wrlvl_override = 1
> > > > wrlvl_sample = 10
> > > > wrlvl_start = 8
> > > > rcw_override = 0
> > > > rcw_1 = 0
> > > > rcw_2 = 0
> > > > tCKE_clock_pulse_width_ps = 9000
> > > > tFAW_window_four_activates_ps = 0
> > > > trwt_override = 0
> > > > trwt = 0
> > > >
> > > >
> > > > Address Assignment: Controller=0 DIMM=0
> > > > Don't have this functionality yet
> > > >
> > > >
> > > > Computed Register Values: Controller=0
> > > > cs0_bnds = 0x0000007F
> > > > cs0_config = 0x80014400
> > > > cs0_config_2 = 0x00000000
> > > > cs1_bnds = 0x00000000
> > > > cs1_config = 0x80014400
> > > > cs1_config_2 = 0x00000000
> > > > timing_cfg_3 = 0x000F0000
> > > > timing_cfg_0 = 0x40110104
> > > > timing_cfg_1 = 0x000F8246
> > > > timing_cfg_2 = 0x0FA8D0C0
> > > > ddr_sdram_cfg = 0xC7004000
> > > > ddr_sdram_cfg_2 = 0x24401040
> > > > ddr_sdram_mode = 0x00401021
> > > > ddr_sdram_mode_2 = 0x00000000
> > > > ddr_sdram_mode_3 = 0x00000000
> > > > ddr_sdram_mode_4 = 0x00000000
> > > > ddr_sdram_mode_5 = 0x00000000
> > > > ddr_sdram_mode_6 = 0x00000000
> > > > ddr_sdram_mode_7 = 0x00000000
> > > > ddr_sdram_mode_8 = 0x00000000
> > > > ddr_sdram_interval = 0x00000100
> > > > ddr_data_init = 0xDEADBEEF
> > > > ddr_sdram_clk_cntl = 0x03000000
> > > > ddr_init_addr = 0x00000000
> > > > ddr_init_ext_addr = 0x00000000
> > > > timing_cfg_4 = 0x00220001
> > > > timing_cfg_5 = 0x1C401400
> > > > ddr_zq_cntl = 0x89080600
> > > > ddr_wrlvl_cntl = 0x8675A608
> > > > ddr_sr_cntr = 0x00000000
> > > > ddr_sdram_rcw_1 = 0x00000000
> > > > ddr_sdram_rcw_2 = 0x00000000
> > > > ddr_cdr1 = 0x00000000
> > > > ddr_cdr2 = 0x00000000
> > > > err_disable = 0x00000000
> > > > err_int_en = 0x00000000
> > > > debug_01 = 0x00000000
> > > > debug_02 = 0x00000000
> > > > debug_03 = 0x00000000
> > > > debug_04 = 0x00000000
> > > > debug_05 = 0x00000000
> > > > debug_06 = 0x00000000
> > > > debug_07 = 0x00000000
> > > > debug_08 = 0x00000000
> > > > debug_09 = 0x00000000
> > > > debug_10 = 0x00000000
> > > > debug_11 = 0x00000000
> > > > debug_12 = 0x00000000
> > > > debug_13 = 0x00000000
> > > > debug_14 = 0x00000000
> > > > debug_15 = 0x00000000
> > > > debug_16 = 0x00000000
> > > > debug_17 = 0x00000000
> > > > debug_18 = 0x00000000
> > > > debug_19 = 0x00000000
> > > > debug_20 = 0x00000000
> > > > debug_21 = 0x00000000
> > > > debug_22 = 0x00000000
> > > > debug_23 = 0x00000000
> > > > debug_24 = 0x00000000
> > > > debug_25 = 0x00000000
> > > > debug_26 = 0x00000000
> > > > debug_27 = 0x00000000
> > > > debug_28 = 0x00000000
> > > > debug_29 = 0x00000000
> > > > debug_30 = 0x00000000
> > > > debug_31 = 0x00000000
> > > > debug_32 = 0x00000000
> > > >
> > > > _______________________________________________
> > > > U-Boot mailing list
> > > > U-Boot at lists.denx.de
> > > > http://lists.denx.de/mailman/listinfo/u-boot
> > > >
> >
> >
> >
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > http://lists.denx.de/mailman/listinfo/u-boot
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
More information about the U-Boot
mailing list