[U-Boot] [PATCH 07/11] MX5: mx53evk: use new pmic driver

Stefano Babic sbabic at denx.de
Sat Oct 8 12:07:04 CEST 2011


Switch to new pmic generic driver.

Signed-off-by: Stefano Babic <sbabic at denx.de>
CC: Jason Liu <jason.hui at linaro.org>
---
 board/freescale/mx53evk/mx53evk.c |   15 +++++++++------
 include/configs/mx53evk.h         |    5 +++--
 2 files changed, 12 insertions(+), 8 deletions(-)

diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c
index fd821c0..af0948f 100644
--- a/board/freescale/mx53evk/mx53evk.c
+++ b/board/freescale/mx53evk/mx53evk.c
@@ -32,6 +32,7 @@
 #include <i2c.h>
 #include <mmc.h>
 #include <fsl_esdhc.h>
+#include <pmic.h>
 #include <fsl_pmic.h>
 #include <asm/gpio.h>
 #include <mc13892.h>
@@ -124,12 +125,13 @@ static void setup_i2c(unsigned int port_number)
 void power_init(void)
 {
 	unsigned int val;
+	struct pmic *p = get_pmic();
 
 	/* Set VDDA to 1.25V */
-	val = pmic_reg_read(REG_SW_2);
+	pmic_reg_read(p, REG_SW_2, &val);
 	val &= ~SWX_OUT_MASK;
 	val |= SWX_OUT_1_25;
-	pmic_reg_write(REG_SW_2, val);
+	pmic_reg_write(p, REG_SW_2, val);
 
 	/*
 	 * Need increase VCC and VDDA to 1.3V
@@ -137,16 +139,16 @@ void power_init(void)
 	 */
 	if (is_soc_rev(CHIP_REV_2_0) == 0) {
 		/* Set VCC to 1.3V for TO2 */
-		val = pmic_reg_read(REG_SW_1);
+		pmic_reg_read(p, REG_SW_1, &val);
 		val &= ~SWX_OUT_MASK;
 		val |= SWX_OUT_1_30;
-		pmic_reg_write(REG_SW_1, val);
+		pmic_reg_write(p, REG_SW_1, val);
 
 		/* Set VDDA to 1.3V for TO2 */
-		val = pmic_reg_read(REG_SW_2);
+		pmic_reg_read(p, REG_SW_2, &val);
 		val &= ~SWX_OUT_MASK;
 		val |= SWX_OUT_1_30;
-		pmic_reg_write(REG_SW_2, val);
+		pmic_reg_write(p, REG_SW_2, val);
 	}
 }
 
@@ -364,6 +366,7 @@ int board_init(void)
 int board_late_init(void)
 {
 	setup_i2c(1);
+	pmic_init();
 	power_init();
 
 	return 0;
diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h
index b127b06..dfe07bf 100644
--- a/include/configs/mx53evk.h
+++ b/include/configs/mx53evk.h
@@ -59,8 +59,9 @@
 #define CONFIG_SYS_I2C_SLAVE            0xfe
 
 /* PMIC Configs */
-#define CONFIG_FSL_PMIC
-#define CONFIG_FSL_PMIC_I2C
+#define CONFIG_PMIC
+#define CONFIG_PMIC_I2C
+#define CONFIG_PMIC_FSL
 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR    8
 
 /* MMC Configs */
-- 
1.7.1



More information about the U-Boot mailing list