[U-Boot] [PATCH v3 08/24] mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance
Joe Hershberger
joe.hershberger at ni.com
Wed Oct 12 06:57:15 CEST 2011
Signed-off-by: Joe Hershberger <joe.hershberger at ni.com>
Cc: Joe Hershberger <joe.hershberger at gmail.com>
Cc: Kim Phillips <kim.phillips at freescale.com>
---
include/configs/MPC8349ITX.h | 328 ++++++++++++++++++++++++++----------------
1 files changed, 204 insertions(+), 124 deletions(-)
diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h
index de233ff..c98c675 100644
--- a/include/configs/MPC8349ITX.h
+++ b/include/configs/MPC8349ITX.h
@@ -71,7 +71,7 @@
#define CONFIG_SYS_TEXT_BASE 0xFEF00000
#endif
-#define CONFIG_SYS_IMMR 0xE0000000 /* The IMMR is relocated to here */
+#define CONFIG_SYS_IMMR 0xE0000000 /* The IMMR is relocated to here */
#define CONFIG_MISC_INIT_F
#define CONFIG_MISC_INIT_R
@@ -81,7 +81,8 @@
*/
#ifdef CONFIG_MPC8349ITX
-#define CONFIG_COMPACT_FLASH /* The CF card interface on the back of the board */
+/* The CF card interface on the back of the board */
+#define CONFIG_COMPACT_FLASH
#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */
#define CONFIG_SATA_SIL3114 /* SIL3114 SATA controller */
#define CONFIG_SYS_USB_HOST /* use the EHCI USB controller */
@@ -111,19 +112,20 @@
#define CONFIG_SYS_I2C_8574A_ADDR1 0x38 /* I2C1, PCF8574A */
#define CONFIG_SYS_I2C_8574A_ADDR2 0x39 /* I2C1, PCF8574A */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C0, Board EEPROM */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/
-#define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/
+#define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/* Don't probe these addresses: */
-#define CONFIG_SYS_I2C_NOPROBES {{1, CONFIG_SYS_I2C_8574_ADDR1}, \
+#define CONFIG_SYS_I2C_NOPROBES { {1, CONFIG_SYS_I2C_8574_ADDR1}, \
{1, CONFIG_SYS_I2C_8574_ADDR2}, \
{1, CONFIG_SYS_I2C_8574A_ADDR1}, \
- {1, CONFIG_SYS_I2C_8574A_ADDR2}}
+ {1, CONFIG_SYS_I2C_8574A_ADDR2} }
/* Bit definitions for the 8574[A] I2C expander */
-#define I2C_8574_REVISION 0x03 /* Board revision, 00=0.0, 01=0.1, 10=1.0 */
+ /* Board revision, 00=0.0, 01=0.1, 10=1.0 */
+#define I2C_8574_REVISION 0x03
#define I2C_8574_CF 0x08 /* 1=Compact flash absent, 0=present */
#define I2C_8574_MPCICLKRN 0x10 /* MiniPCI Clk Run */
#define I2C_8574_PCI66 0x20 /* 0=33MHz PCI, 1=66MHz PCI */
@@ -146,7 +148,8 @@
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0200
#define CONFIG_SYS_ATA_STRIDE 2
-#define ATA_RESET_TIME 1 /* If a CF card is not inserted, time out quickly */
+/* If a CF card is not inserted, time out quickly */
+#define ATA_RESET_TIME 1
#endif
@@ -183,15 +186,15 @@
/*
* DDR Setup
*/
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_83XX_DDR_USES_CS0
-#define CONFIG_SYS_MEMTEST_START 0x1000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_START 0x1000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x2000
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
+ | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
#define CONFIG_VERY_BIG_RAM
#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)256 << 20)
@@ -200,9 +203,12 @@
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
#endif
-#ifndef CONFIG_SPD_EEPROM /* No SPD? Then manually set up DDR parameters */
- #define CONFIG_SYS_DDR_SIZE 256 /* Mb */
- #define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+/* No SPD? Then manually set up DDR parameters */
+#ifndef CONFIG_SPD_EEPROM
+ #define CONFIG_SYS_DDR_SIZE 256 /* Mb */
+ #define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN \
+ | CSCONFIG_ROW_BIT_13 \
+ | CSCONFIG_COL_BIT_10)
#define CONFIG_SYS_DDR_TIMING_1 0x26242321
#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45, may need tuning */
@@ -212,11 +218,12 @@
*Flash on the Local Bus
*/
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_MAX_FLASH_SECT 135 /* 127 64KB sectors + 8 8KB sectors per device */
+/* 127 64KB sectors + 8 8KB sectors per device */
+#define CONFIG_SYS_MAX_FLASH_SECT 135
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
@@ -224,11 +231,12 @@
/* The ITX has two flash chips, but the ITX-GP has only one. To support both
boards, we say we have two, but don't display a message if we find only one. */
#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + 0x800000}
-#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size in MB */
-#define CONFIG_SYS_FLASH_SIZE_SHIFT 4 /* log2 of the above value */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_FLASH_BANKS_LIST \
+ {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + 0x800000}
+#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size in MB */
+#define CONFIG_SYS_FLASH_SIZE_SHIFT 4 /* log2 of the above value */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
/* Vitesse 7385 */
@@ -248,12 +256,19 @@ boards, we say we have two, but don't display a message if we find only one. */
/* Flash */
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 | BR_V)
-#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
- OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \
+ | OR_UPM_XAM \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | (0x13 + CONFIG_SYS_FLASH_SIZE_SHIFT))
+#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \
+ | (0x13 + CONFIG_SYS_FLASH_SIZE_SHIFT))
/* Vitesse 7385 */
@@ -261,10 +276,15 @@ boards, we say we have two, but don't display a message if we find only one. */
#ifdef CONFIG_VSC7385_ENET
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_VSC7385_BASE | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
- OR_GPCM_SCY_15 | OR_GPCM_SETA | OR_GPCM_TRLX | \
- OR_GPCM_EHTR | OR_GPCM_EAD)
+#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_VSC7385_BASE | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM (OR_AM_128KB \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_SETA \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_VSC7385_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
@@ -273,20 +293,28 @@ boards, we say we have two, but don't display a message if we find only one. */
/* LED */
-#define CONFIG_SYS_LED_BASE 0xF9000000
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LED_BASE | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_2MB | OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
- OR_GPCM_XACS | OR_GPCM_SCY_9 | OR_GPCM_TRLX | \
- OR_GPCM_EHTR | OR_GPCM_EAD)
+#define CONFIG_SYS_LED_BASE 0xF9000000
+#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LED_BASE | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR2_PRELIM (OR_AM_2MB \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV2 \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_9 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
/* Compact Flash */
#ifdef CONFIG_COMPACT_FLASH
-#define CONFIG_SYS_CF_BASE 0xF0000000
+#define CONFIG_SYS_CF_BASE 0xF0000000
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CF_BASE | BR_PS_16 | BR_MS_UPMA | BR_V)
-#define CONFIG_SYS_OR3_PRELIM (OR_UPM_AM | OR_UPM_BI)
+#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CF_BASE \
+ | BR_PS_16 \
+ | BR_MS_UPMA \
+ | BR_V)
+#define CONFIG_SYS_OR3_PRELIM (OR_UPM_AM | OR_UPM_BI)
#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CF_BASE
#define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_64KB)
@@ -305,15 +333,16 @@ boards, we say we have two, but don't display a message if we find only one. */
#endif
#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
+#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/*
* Local Bus LCRR and LBCR regs
@@ -325,8 +354,10 @@ boards, we say we have two, but don't display a message if we find only one. */
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
-#define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32*/
+ /* LB sdram refresh timer, about 6us */
+#define CONFIG_SYS_LBC_LSRT 0x32000000
+ /* LB refresh timer prescal, 266MHz/32*/
+#define CONFIG_SYS_LBC_MRTPR 0x20000000
/*
* Serial Port
@@ -338,7 +369,7 @@ boards, we say we have two, but don't display a message if we find only one. */
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_CONSOLE ttyS0
#define CONFIG_BAUDRATE 115200
@@ -365,23 +396,27 @@ boards, we say we have two, but don't display a message if we find only one. */
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
+#define CONFIG_SYS_PCI1_MMIO_BASE \
+ (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */
#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_PCI2_MEM_BASE (CONFIG_SYS_PCI1_MMIO_BASE + CONFIG_SYS_PCI1_MMIO_SIZE)
+#define CONFIG_SYS_PCI2_MEM_BASE \
+ (CONFIG_SYS_PCI1_MMIO_BASE + CONFIG_SYS_PCI1_MMIO_SIZE)
#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE (CONFIG_SYS_PCI2_MEM_BASE + CONFIG_SYS_PCI2_MEM_SIZE)
+#define CONFIG_SYS_PCI2_MMIO_BASE \
+ (CONFIG_SYS_PCI2_MEM_BASE + CONFIG_SYS_PCI2_MEM_SIZE)
#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS (CONFIG_SYS_PCI1_IO_PHYS + CONFIG_SYS_PCI1_IO_SIZE)
-#define CONFIG_SYS_PCI2_IO_SIZE 0x01000000 /* 16M */
+#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS \
+ (CONFIG_SYS_PCI1_IO_PHYS + CONFIG_SYS_PCI1_IO_SIZE)
+#define CONFIG_SYS_PCI2_IO_SIZE 0x01000000 /* 16M */
#endif
#define CONFIG_NET_MULTI
@@ -444,15 +479,16 @@ boards, we say we have two, but don't display a message if we find only one. */
#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+ #define CONFIG_ENV_ADDR \
+ (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for environment */
- #define CONFIG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_SIZE 0x2000
#else
- #define CONFIG_SYS_NO_FLASH /* Flash is not usable now */
+ #define CONFIG_SYS_NO_FLASH /* Flash is not usable now */
#undef CONFIG_FLASH_CFI_DRIVER
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
- #define CONFIG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO /* echo on for serial download */
@@ -481,30 +517,30 @@ boards, we say we have two, but don't display a message if we find only one. */
#define CONFIG_CMD_SDRAM
#if defined(CONFIG_COMPACT_FLASH) || defined(CONFIG_SATA_SIL3114) \
- || defined(CONFIG_USB_STORAGE)
- #define CONFIG_DOS_PARTITION
- #define CONFIG_CMD_FAT
- #define CONFIG_SUPPORT_VFAT
+ || defined(CONFIG_USB_STORAGE)
+ #define CONFIG_DOS_PARTITION
+ #define CONFIG_CMD_FAT
+ #define CONFIG_SUPPORT_VFAT
#endif
#ifdef CONFIG_COMPACT_FLASH
- #define CONFIG_CMD_IDE
+ #define CONFIG_CMD_IDE
#endif
#ifdef CONFIG_SATA_SIL3114
- #define CONFIG_CMD_SATA
+ #define CONFIG_CMD_SATA
#endif
#if defined(CONFIG_SATA_SIL3114) || defined(CONFIG_USB_STORAGE)
- #define CONFIG_CMD_EXT2
+ #define CONFIG_CMD_EXT2
#endif
#ifdef CONFIG_PCI
- #define CONFIG_CMD_PCI
+ #define CONFIG_CMD_PCI
#endif
#ifdef CONFIG_HARD_I2C
- #define CONFIG_CMD_I2C
+ #define CONFIG_CMD_I2C
#endif
/* Watchdog */
@@ -513,38 +549,41 @@ boards, we say we have two, but don't display a message if we find only one. */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#ifdef CONFIG_MPC8349ITX
-#define CONFIG_SYS_PROMPT "MPC8349E-mITX> " /* Monitor Command Prompt */
+#define CONFIG_SYS_PROMPT "MPC8349E-mITX> " /* Monitor Command Prompt */
#else
-#define CONFIG_SYS_PROMPT "MPC8349E-mITX-GP> " /* Monitor Command Prompt */
+#define CONFIG_SYS_PROMPT "MPC8349E-mITX-GP> " /* Monitor Command Prompt */
#endif
#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+ /* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+ /* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/
+ /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
@@ -565,7 +604,7 @@ boards, we say we have two, but don't display a message if we find only one. */
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII )
+ HRCWH_TSEC2M_IN_GMII)
#else
#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
@@ -578,14 +617,14 @@ boards, we say we have two, but don't display a message if we find only one. */
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_TSEC1M_IN_GMII |\
- HRCWH_TSEC2M_IN_GMII )
+ HRCWH_TSEC2M_IN_GMII)
#endif
/*
* System performance
*/
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
#define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
@@ -596,8 +635,10 @@ boards, we say we have two, but don't display a message if we find only one. */
/*
* System IO Config
*/
-#define CONFIG_SYS_SICRH SICRH_TSOBI1 /* Needed for gigabit to work on TSEC 1 */
-#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1) /* USB DR as device + USB MPH as host */
+/* Needed for gigabit to work on TSEC 1 */
+#define CONFIG_SYS_SICRH SICRH_TSOBI1
+ /* USB DR as device + USB MPH as host */
+#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1)
#define CONFIG_SYS_HID0_INIT 0x00000000
#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_INSTRUCTION_CACHE
@@ -606,15 +647,31 @@ boards, we say we have two, but don't display a message if we find only one. */
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
+ | BATL_PP_10 \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
/* PCI */
#ifdef CONFIG_PCI
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
+ | BATL_PP_10 \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
+ | BATL_PP_10 \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
#else
#define CONFIG_SYS_IBAT1L 0
#define CONFIG_SYS_IBAT1U 0
@@ -623,10 +680,21 @@ boards, we say we have two, but don't display a message if we find only one. */
#endif
#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \
+ | BATL_PP_10 \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \
+ | BATL_PP_10 \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
#else
#define CONFIG_SYS_IBAT3L 0
#define CONFIG_SYS_IBAT3U 0
@@ -635,13 +703,24 @@ boards, we say we have two, but don't display a message if we find only one. */
#endif
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
+ | BATL_PP_10 \
+ | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE | \
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L (0xF0000000 \
+ | BATL_PP_10 \
+ | BATL_MEMCOHERENCE \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U (0xF0000000 \
+ | BATU_BL_256M \
+ | BATU_VS \
+ | BATU_VP)
#define CONFIG_SYS_IBAT7L 0
#define CONFIG_SYS_IBAT7U 0
@@ -674,23 +753,24 @@ boards, we say we have two, but don't display a message if we find only one. */
*/
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_NETDEV eth0
+#define CONFIG_NETDEV "eth0"
#ifdef CONFIG_MPC8349ITX
-#define CONFIG_HOSTNAME mpc8349emitx
+#define CONFIG_HOSTNAME "mpc8349emitx"
#else
-#define CONFIG_HOSTNAME mpc8349emitxgp
+#define CONFIG_HOSTNAME "mpc8349emitxgp"
#endif
/* Default path and filenames */
#define CONFIG_ROOTPATH /nfsroot/rootfs
#define CONFIG_BOOTFILE uImage
-#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
+ /* U-Boot image on TFTP server */
+#define CONFIG_UBOOTPATH "u-boot.bin"
#ifdef CONFIG_MPC8349ITX
-#define CONFIG_FDTFILE mpc8349emitx.dtb
+#define CONFIG_FDTFILE "mpc8349emitx.dtb"
#else
-#define CONFIG_FDTFILE mpc8349emitxgp.dtb
+#define CONFIG_FDTFILE "mpc8349emitxgp.dtb"
#endif
#define CONFIG_BOOTDELAY 6
@@ -700,28 +780,28 @@ boards, we say we have two, but don't display a message if we find only one. */
#define CONFIG_BOOTARGS \
"root=/dev/nfs rw" \
- " nfsroot=" MK_STR(CONFIG_SERVERIP) ":" MK_STR(CONFIG_ROOTPATH) \
+ " nfsroot=" MK_STR(CONFIG_SERVERIP) ":" MK_STR(CONFIG_ROOTPATH) \
" ip=" MK_STR(CONFIG_IPADDR) ":" MK_STR(CONFIG_SERVERIP) ":" \
- MK_STR(CONFIG_GATEWAYIP) ":" MK_STR(CONFIG_NETMASK) ":" \
- MK_STR(CONFIG_HOSTNAME) ":" MK_STR(CONFIG_NETDEV) ":off" \
+ MK_STR(CONFIG_GATEWAYIP) ":" MK_STR(CONFIG_NETMASK) ":" \
+ CONFIG_HOSTNAME ":" CONFIG_NETDEV ":off" \
" console=" MK_STR(CONFIG_CONSOLE) "," MK_STR(CONFIG_BAUDRATE)
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=" MK_STR(CONFIG_CONSOLE) "\0" \
- "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "netdev=" CONFIG_NETDEV "\0" \
+ "uboot=" CONFIG_UBOOTPATH "\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \
- "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
+ "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "\
+ "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; "\
+ "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; "\
+ "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0"\
"fdtaddr=780000\0" \
- "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"
+ "fdtfile=" CONFIG_FDTFILE "\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath" \
- " ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ " ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\
" console=$console,$baudrate $othbootargs; " \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
--
1.6.0.2
More information about the U-Boot
mailing list