[U-Boot] [PATCH v5 4/5] tegra2: Modify MMC driver to handle power and cd GPIOs

Stephen Warren swarren at nvidia.com
Wed Oct 12 19:52:36 CEST 2011


Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.

Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.

Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.

v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
    Remove prototype of gpio_config_mmc() from board.h

Signed-off-by: Stephen Warren <swarren at nvidia.com>
Tested-by: Simon Glass <sjg at chromium.org>
---
 board/nvidia/common/board.h      |    3 +-
 board/nvidia/harmony/harmony.c   |   27 ++---------------------
 board/nvidia/seaboard/seaboard.c |   33 +----------------------------
 drivers/mmc/tegra2_mmc.c         |   42 ++++++++++++++++++++++++++++++++-----
 drivers/mmc/tegra2_mmc.h         |    4 ++-
 5 files changed, 45 insertions(+), 64 deletions(-)

diff --git a/board/nvidia/common/board.h b/board/nvidia/common/board.h
index 344e702..35acbca 100644
--- a/board/nvidia/common/board.h
+++ b/board/nvidia/common/board.h
@@ -26,7 +26,6 @@
 
 void tegra2_start(void);
 void gpio_config_uart(void);
-void gpio_config_mmc(void);
-int tegra2_mmc_init(int dev_index, int bus_width);
+int tegra2_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio);
 
 #endif	/* BOARD_H */
diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c
index f2c3867..3cbe820 100644
--- a/board/nvidia/harmony/harmony.c
+++ b/board/nvidia/harmony/harmony.c
@@ -25,6 +25,7 @@
 #include <asm/io.h>
 #include <asm/arch/tegra2.h>
 #include <asm/arch/pinmux.h>
+#include <asm/gpio.h>
 #ifdef CONFIG_TEGRA2_MMC
 #include <mmc.h>
 #endif
@@ -72,15 +73,6 @@ static void pin_mux_mmc(void)
 	pinmux_tristate_disable(PINGRP_ATC);
 }
 
-/*
- * Routine: gpio_config_mmc
- * Description: Set GPIOs for SD card
- */
-void gpio_config_mmc(void)
-{
-	/* Not implemented for now */
-}
-
 /* this is a weak define that we are overriding */
 int board_mmc_init(bd_t *bd)
 {
@@ -88,29 +80,16 @@ int board_mmc_init(bd_t *bd)
 
 	/* Enable muxes, etc. for SDMMC controllers */
 	pin_mux_mmc();
-	gpio_config_mmc();
 
 	debug("board_mmc_init: init SD slot J26\n");
 	/* init dev 0, SD slot J26, with 4-bit bus */
 	/* The board has an 8-bit bus, but 8-bit doesn't work yet */
-	tegra2_mmc_init(0, 4);
+	tegra2_mmc_init(0, 4, GPIO_PI6, GPIO_PH2);
 
 	debug("board_mmc_init: init SD slot J5\n");
 	/* init dev 2, SD slot J5, with 4-bit bus */
-	tegra2_mmc_init(2, 4);
+	tegra2_mmc_init(2, 4, GPIO_PT3, GPIO_PI5);
 
 	return 0;
 }
-
-/* this is a weak define that we are overriding */
-int board_mmc_getcd(u8 *cd, struct mmc *mmc)
-{
-	debug("board_mmc_getcd called\n");
-	/*
-	 * Hard-code CD presence for now. Need to add GPIO inputs
-	 * for Harmony
-	 */
-	*cd = 1;
-	return 0;
-}
 #endif
diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c
index 22a0e69..356d616 100644
--- a/board/nvidia/seaboard/seaboard.c
+++ b/board/nvidia/seaboard/seaboard.c
@@ -87,19 +87,6 @@ static void pin_mux_mmc(void)
 	pinmux_tristate_disable(PINGRP_ATC);
 }
 
-/*
- * Routine: gpio_config_mmc
- * Description: Set GPIOs for SDMMC3 SDIO slot.
- */
-void gpio_config_mmc(void)
-{
-	/* Set EN_VDDIO_SD (GPIO I6) */
-	gpio_direction_output(GPIO_PI6, 1);
-
-	/* Config pin as GPI for Card Detect (GPIO I5) */
-	gpio_direction_input(GPIO_PI5);
-}
-
 /* this is a weak define that we are overriding */
 int board_mmc_init(bd_t *bd)
 {
@@ -107,31 +94,15 @@ int board_mmc_init(bd_t *bd)
 
 	/* Enable muxes, etc. for SDMMC controllers */
 	pin_mux_mmc();
-	gpio_config_mmc();
 
 	debug("board_mmc_init: init eMMC\n");
 	/* init dev 0, eMMC chip, with 4-bit bus */
 	/* The board has an 8-bit bus, but 8-bit doesn't work yet */
-	tegra2_mmc_init(0, 4);
+	tegra2_mmc_init(0, 4, -1, -1);
 
 	debug("board_mmc_init: init SD slot\n");
 	/* init dev 1, SD slot, with 4-bit bus */
-	tegra2_mmc_init(1, 4);
-
-	return 0;
-}
-
-/* this is a weak define that we are overriding */
-int board_mmc_getcd(u8 *cd, struct mmc *mmc)
-{
-	debug("board_mmc_getcd called\n");
-	*cd = 1;			/* Assume card is inserted, or eMMC */
-
-	if (IS_SD(mmc)) {
-		/* Seaboard SDMMC3 = SDIO3_CD = GPIO_PI5 */
-		if (gpio_get_value(GPIO_PI5))
-			*cd = 0;
-	}
+	tegra2_mmc_init(1, 4, GPIO_PI6, GPIO_PI5);
 
 	return 0;
 }
diff --git a/drivers/mmc/tegra2_mmc.c b/drivers/mmc/tegra2_mmc.c
index 78b1190..3de9c5d 100644
--- a/drivers/mmc/tegra2_mmc.c
+++ b/drivers/mmc/tegra2_mmc.c
@@ -21,6 +21,7 @@
 
 #include <common.h>
 #include <mmc.h>
+#include <asm/gpio.h>
 #include <asm/io.h>
 #include <asm/arch/clk_rst.h>
 #include <asm/arch/clock.h>
@@ -433,20 +434,37 @@ static int mmc_core_init(struct mmc *mmc)
 	return 0;
 }
 
-static int tegra2_mmc_initialize(int dev_index, int bus_width)
+int tegra2_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio)
 {
 	struct mmc_host *host;
+	char gpusage[12]; /* "SD/MMCn PWR" or "SD/MMCn CD" */
 	struct mmc *mmc;
 
-	debug(" mmc_initialize called\n");
+	debug(" tegra2_mmc_init: index %d, bus width %d "
+		"pwr_gpio %d cd_gpio %d\n",
+		dev_index, bus_width, pwr_gpio, cd_gpio);
 
 	host = &mmc_host[dev_index];
 
 	host->clock = 0;
+	host->pwr_gpio = pwr_gpio;
+	host->cd_gpio = cd_gpio;
 	tegra2_get_setup(host, dev_index);
 
 	clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000);
 
+	if (host->pwr_gpio >= 0) {
+		sprintf(gpusage, "SD/MMC%d PWR", dev_index);
+		gpio_request(host->pwr_gpio, gpusage);
+		gpio_direction_output(host->pwr_gpio, 1);
+	}
+
+	if (host->cd_gpio >= 0) {
+		sprintf(gpusage, "SD/MMC%d CD", dev_index);
+		gpio_request(host->cd_gpio, gpusage);
+		gpio_direction_input(host->cd_gpio);
+	}
+
 	mmc = &mmc_dev[dev_index];
 
 	sprintf(mmc->name, "Tegra2 SD/MMC");
@@ -478,9 +496,21 @@ static int tegra2_mmc_initialize(int dev_index, int bus_width)
 	return 0;
 }
 
-int tegra2_mmc_init(int dev_index, int bus_width)
+/* this is a weak define that we are overriding */
+int board_mmc_getcd(u8 *cd, struct mmc *mmc)
 {
-	debug(" tegra2_mmc_init: index %d, bus width %d\n",
-		dev_index, bus_width);
-	return tegra2_mmc_initialize(dev_index, bus_width);
+	struct mmc_host *host = (struct mmc_host *)mmc->priv;
+
+	debug("board_mmc_getcd called\n");
+
+	*cd = 1; /* Assume card is inserted, or eMMC */
+
+	if (IS_SD(mmc)) {
+		if (host->cd_gpio >= 0) {
+			if (gpio_get_value(host->cd_gpio))
+				*cd = 0;
+		}
+	}
+
+	return 0;
 }
diff --git a/drivers/mmc/tegra2_mmc.h b/drivers/mmc/tegra2_mmc.h
index 28698e0..72f587b 100644
--- a/drivers/mmc/tegra2_mmc.h
+++ b/drivers/mmc/tegra2_mmc.h
@@ -74,9 +74,11 @@ struct mmc_host {
 	unsigned int clock;	/* Current clock (MHz) */
 	unsigned int base;	/* Base address, SDMMC1/2/3/4 */
 	enum periph_id mmc_id;	/* Peripheral ID: PERIPH_ID_... */
+	int pwr_gpio;		/* Power GPIO */
+	int cd_gpio;		/* Change Detect GPIO */
 };
 
-int tegra2_mmc_init(int dev_index, int bus_width);
+int tegra2_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio);
 
 #endif	/* __ASSEMBLY__ */
 #endif	/* __TEGRA2_MMC_H_ */
-- 
1.7.0.4



More information about the U-Boot mailing list