[U-Boot] Please pull u-boot-ti/master
Albert ARIBAUD
albert.u.boot at aribaud.net
Fri Oct 21 20:12:06 CEST 2011
Hi Sandeep,
Le 21/10/2011 19:00, s-paulraj at ti.com a écrit :
> Albert,
> Please pull u-boot-ti/master
>
> Regards,
> Sandeep
>
>
> The following changes since commit efb2172ece93ef48f34fb8bdf963d3b72880cc7d:
> Simon Glass (1):
> Move timestamp and version files into 'generated' subdir
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-ti.git master
>
> Aneesh V (1):
> omap: spl: fix build break due to changes in FAT
>
> Chandan Nath (5):
> ARM:AM33XX: Added support for AM33xx
> ARM:AM33XX: Add clock definitions
> ARM:AM33XX: Add emif/ddr support
> ARM:AM33XX: Added timer support
> ARM:AM33XX: Add support for TI AM335X EVM
>
> Christian Riesch (1):
> da850evm: Move LPSC configuration to board_early_init_f()
>
> Heiko Schocher (1):
> arm, davinci: add missing LSPC define for MMC/SD1
>
> Ilya Yanok (1):
> omap3/emif4: fix registers definition
>
> Joe Hershberger (2):
> omap: Don't use gpio_free to change direction to input
> omap4_panda: Build in cmd_gpio support on panda
>
> Joel A Fernandes (1):
> Makefile: Remove MLO on make clean
>
> Manjunath Hadli (6):
> dm644X: revert cache disable patch
> dm36x: revert cache disable patch
> da830: add support for NAND boot mode
> davinci: emac: add new features to autonegotiate for EMAC
> davinci: emac: add support for more than 1 PHYs
> davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
>
> Philip Balister (3):
> OMAP3: overo : Use ttyO2 instead of ttyS2.
> OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
> OMAP3: overo : Add environment variable optargs to bootargs
>
> Ricardo Salveti de Araujo (3):
> omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
> omap4: adding revision detection for 4460 ES1.1
> omap4: splitting padconfs into common, 4430 and 4460
>
> SRICHARAN R (1):
> U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
>
> Sergei Shtylyov (1):
> DaVinci: correct MDSTAT.STATE mask
>
> Simon Schwarz (4):
> omap3: Add Base register for DMA
> omap3: Add DMA register accessors
> omap3: Add interface for omap3 DMA
> SPL: Add DMA library
>
> Steve Sakoman (3):
> omap: overo: Configure mux for gpio10
> omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
> omap: beagle: Use ubifs instead of jffs2 for nand boot
>
> Tom Rini (3):
> OMAP3 SPL: Provide weak omap_rev_string
> devkit8000: Add malloc space
> mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
>
> Vladimir Zapolskiy (1):
> davinci: remove config.mk file from the sources
Applied to u-boot-arm/master (with rebase, as the pull request was based
on u-boot, not u-boot-arm), thanks!
Amicalement,
--
Albert.
More information about the U-Boot
mailing list