[U-Boot] [PATCH 17/17] M28: Add memory detection into SPL

Marek Vasut marek.vasut at gmail.com
Sat Oct 22 00:44:26 CEST 2011


This code allows the DDR DRAM size to be detected at runtime. The RAM size is
stored into two scratch registers, from which it is then fetched in U-Boot.

Signed-off-by: Marek Vasut <marek.vasut at gmail.com>
---
 board/denx/m28evk/Makefile   |    7 ++++++-
 board/denx/m28evk/m28evk.c   |   18 ++++++++++++++++--
 board/denx/m28evk/mem_init.c |   27 +++++++++++++++++++++++++++
 include/configs/m28evk.h     |    2 +-
 4 files changed, 50 insertions(+), 4 deletions(-)

diff --git a/board/denx/m28evk/Makefile b/board/denx/m28evk/Makefile
index 953143a..7bafff5 100644
--- a/board/denx/m28evk/Makefile
+++ b/board/denx/m28evk/Makefile
@@ -30,7 +30,7 @@ COBJS	:= m28evk.o
 endif
 
 ifdef	CONFIG_SPL_BUILD
-COBJS	:= mem_init.o mmc_boot.o power_init.o
+COBJS	:= mem_init.o mmc_boot.o power_init.o memsize.o
 endif
 
 SRCS	:= $(COBJS:.o=.c)
@@ -47,6 +47,11 @@ clean:
 distclean:	clean
 	rm -f $(LIB) core *.bak .depend
 
+ifdef	CONFIG_SPL_BUILD
+memsize.c:
+	ln -sf $(TOPDIR)/common/memsize.c $@
+endif
+
 #########################################################################
 
 # defines $(obj).depend target
diff --git a/board/denx/m28evk/m28evk.c b/board/denx/m28evk/m28evk.c
index 118e222..168ceeb 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/denx/m28evk/m28evk.c
@@ -63,10 +63,24 @@ int board_init(void)
 	return 0;
 }
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
 int dram_init(void)
 {
-	/* dram_init must store complete ramsize in gd->ram_size */
-	gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+	uint32_t sz[2];
+
+	sz[0] = readl(HW_DIGCTRL_SCRATCH0);
+	sz[1] = readl(HW_DIGCTRL_SCRATCH1);
+
+	if (sz[0] != sz[1]) {
+		printf("MX28:\n"
+			"Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
+			"HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
+			"verify these two registers contain valid RAM size!\n");
+		hang();
+	}
+
+	gd->ram_size = sz[0];
 	return 0;
 }
 
diff --git a/board/denx/m28evk/mem_init.c b/board/denx/m28evk/mem_init.c
index 066fe0d..17d1f9b 100644
--- a/board/denx/m28evk/mem_init.c
+++ b/board/denx/m28evk/mem_init.c
@@ -165,6 +165,31 @@ void mx28_mem_setup_vddd(void)
 		&power_regs->hw_power_vdddctrl);
 }
 
+#define	HW_DIGCTRL_SCRATCH0	0x8001c280
+#define	HW_DIGCTRL_SCRATCH1	0x8001c290
+void data_abort_memdetect_handler(void) __attribute__((naked));
+void data_abort_memdetect_handler(void)
+{
+	asm volatile("subs pc, r14, #4");
+}
+
+void mx28_mem_get_size(void)
+{
+	uint32_t sz, da;
+	uint32_t *vt = (uint32_t *)0x20;
+
+	/* Replace the DABT handler. */
+	da = vt[4];
+	vt[4] = (uint32_t)&data_abort_memdetect_handler;
+
+	sz = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
+	writel(sz, HW_DIGCTRL_SCRATCH0);
+	writel(sz, HW_DIGCTRL_SCRATCH1);
+
+	/* Restore the old DABT handler. */
+	vt[4] = da;
+}
+
 void mx28_mem_init(void)
 {
 	struct mx28_clkctrl_regs *clkctrl_regs =
@@ -210,4 +235,6 @@ void mx28_mem_init(void)
 	early_delay(10000);
 
 	mx28_mem_setup_cpu_and_hbus();
+
+	mx28_mem_get_size();
 }
diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h
index 381b01e..c8b0cf5 100644
--- a/include/configs/m28evk.h
+++ b/include/configs/m28evk.h
@@ -81,7 +81,7 @@
  */
 #define	CONFIG_NR_DRAM_BANKS		1		/* 2 banks of DRAM */
 #define	PHYS_SDRAM_1			0x40000000	/* Base address */
-#define	PHYS_SDRAM_1_SIZE		0x08000000	/* 128 MB */
+#define	PHYS_SDRAM_1_SIZE		0x40000000	/* Max 1 GB RAM */
 #define	CONFIG_STACKSIZE		0x00010000	/* 128 KB stack */
 #define	CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for malloc */
 #define	CONFIG_SYS_GBL_DATA_SIZE	128		/* Initial data */
-- 
1.7.6.3



More information about the U-Boot mailing list