[U-Boot] [PATCHv2 2/6] omap3evm: Prepare to split configuration
Sanjeev Premi
premi at ti.com
Tue Oct 25 18:11:29 CEST 2011
This patch marks the beginning of steps that would
lead to clean and easy split of the configuration
file. Common portion can then be re-used by other
configurations.
Signed-off-by: Sanjeev Premi <premi at ti.com>
Cc: Sandeep Paulraj <s-paulraj at ti.com>
---
Since the patch changes most of the file contents, it may
not be easy to review. This sequence on individual patches
that were squashed to make this change can be viewed at:
http://pastebin.com/0utWswst
Since, this was a set of patches with no real change in
functionality, i didn't post them to the list.
Changes in v2:
Minor edits due to removal of CONFIG_NET_MULTI since previous
revision. The URL above (pastebin) doesn't reflect these changes.
include/configs/omap3_evm.h | 194 +++++++++++++++++++++++++++++--------------
1 files changed, 132 insertions(+), 62 deletions(-)
diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
index 6319e32..8a55614 100644
--- a/include/configs/omap3_evm.h
+++ b/include/configs/omap3_evm.h
@@ -1,6 +1,8 @@
/*
- * (C) Copyright 2006-2008
- * Texas Instruments.
+ * Configuration settings for the TI OMAP3 EVM board.
+ *
+ * Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
* Author :
* Manikandan Pillai <mani.pillai at ti.com>
* Derived from Beagle Board and 3430 SDP code by
@@ -9,8 +11,6 @@
*
* Manikandan Pillai <mani.pillai at ti.com>
*
- * Configuration settings for the TI OMAP3 EVM board.
- *
* See file CREDITS for list of people who contributed to this
* project.
*
@@ -30,11 +30,130 @@
* MA 02111-1307 USA
*/
-#ifndef __CONFIG_H
-#define __CONFIG_H
+#ifndef __OMAP3EVM_CONFIG_H
+#define __OMAP3EVM_CONFIG_H
+
+#include <asm/arch/cpu.h>
+#include <asm/arch/omap3.h>
+
+/* =============================================================================
+ * This section holds the common definitions that correspond to the
+ * current default configuration - omap3_evm_config
+ * =============================================================================
+ */
+
+/* ----------------------------------------------------------------------------
+ * Supported U-boot commands
+ * ----------------------------------------------------------------------------
+ */
+
+/* Default commands to include */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EXT2 /* EXT2 Support */
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+
+#define CONFIG_CMD_I2C /* I2C serial bus support */
+#define CONFIG_CMD_MMC /* MMC support */
+#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+
+#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
+#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
+#undef CONFIG_CMD_IMI /* iminfo */
+#undef CONFIG_CMD_IMLS /* List all found images */
+
+/* ----------------------------------------------------------------------------
+ * Supported U-boot features
+ * ----------------------------------------------------------------------------
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+
+/* Display CPU and Board information */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Add auto-completion support */
+#define CONFIG_AUTO_COMPLETE
+
+/* ----------------------------------------------------------------------------
+ * Supported hardware
+ * ----------------------------------------------------------------------------
+ */
+
+/* MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_DOS_PARTITION
+
+/* USB
+ *
+ * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
+ * Enable CONFIG_MUSB_UDD for Device functionalities.
+ */
+#define CONFIG_USB_OMAP3
+#define CONFIG_MUSB_HCD
+/* #define CONFIG_MUSB_UDC */
+
+/* -----------------------------------------------------------------------------
+ * Default environment
+ * -----------------------------------------------------------------------------
+ */
+#define CONFIG_BOOTDELAY 10
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "usbtty=cdc_acm\0" \
+ "mmcdev=0\0" \
+ "memsize=128M\0" \
+ "console=ttyO0,115200n8\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "mem=${memsize}\0 " \
+ "root=/dev/mmcblk0p2 rw " \
+ "rootfstype=ext3 rootwait\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "mem=${memsize}\0 " \
+ "root=/dev/mtdblock4 rw " \
+ "rootfstype=jffs2\0" \
+ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source ${loadaddr}\0" \
+ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "onenand read ${loadaddr} 280000 400000; " \
+ "bootm ${loadaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "if mmc rescan ${mmcdev}; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run nandboot; " \
+ "fi; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+/* =============================================================================
+ * This section holds the common definitions that can be used by
+ * all OMAP3EVM based configurations.
+ * =============================================================================
+ */
/*
- * High Level Configuration Options
+ * High level configuration options
*/
#define CONFIG_OMAP /* This is TI OMAP core */
#define CONFIG_OMAP34XX /* belonging to 34XX family */
@@ -46,12 +165,6 @@
#define CONFIG_OMAP3_MICRON_DDR /* with MICRON DDR part */
#define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */
-/*
- * Get cpu and chip specific definitions
- */
-#include <asm/arch/cpu.h>
-#include <asm/arch/omap3.h>
-
#undef CONFIG_USE_IRQ /* no support for IRQs */
/*
@@ -77,10 +190,10 @@
/*
* Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
+ * These values are used in start.S
*/
#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
+
#ifdef CONFIG_USE_IRQ
#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
@@ -193,22 +306,8 @@
#define CONFIG_JFFS2_PART_SIZE 0xf980000
/*
- * MMC
- */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_OMAP_HSMMC
-#define CONFIG_DOS_PARTITION
-
-/* USB
- *
- * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard
- * Enable CONFIG_MUSB_UDD for Device functionalities.
+ * USB
*/
-#define CONFIG_USB_OMAP3
-#define CONFIG_MUSB_HCD
-/* #define CONFIG_MUSB_UDC */
-
#ifdef CONFIG_USB_OMAP3
#ifdef CONFIG_MUSB_HCD
@@ -244,16 +343,10 @@
* U-boot features
* ----------------------------------------------------------------------------
*/
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT "OMAP3_EVM # "
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_MAXARGS 16 /* max args for a command */
-/* Display CPU and Board information */
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
#define CONFIG_MISC_INIT_R
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
@@ -261,12 +354,6 @@
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
-/* Allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Add auto-completion support */
-#define CONFIG_AUTO_COMPLETE
-
/* Size of Console IO buffer */
#define CONFIG_SYS_CBSIZE 512
@@ -277,28 +364,11 @@
/* Size of bootarg buffer */
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-/* Default commands to include */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
-
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_NAND /* NAND support */
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-
-#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
-#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
-#undef CONFIG_CMD_IMI /* iminfo */
-#undef CONFIG_CMD_IMLS /* List all found images */
+#define CONFIG_BOOTFILE uImage
/*
- * Additional definitions that depend on chosen commands
+ * NAND / OneNAND
*/
-/* NAND */
#if defined(CONFIG_CMD_NAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
@@ -393,4 +463,4 @@
"fi; " \
"else run nandboot; fi"
-#endif /* __CONFIG_H */
+#endif /* __OMAP3EVM_CONFIG_H */
--
1.7.0.4
More information about the U-Boot
mailing list