[U-Boot] [PATCH 2/2] WIP: tegra: i2c: Enable new CONFIG_SYS_I2C framework

[Heiko Schocher]

Hello Stephen,

On 31.10.2012 17:25, Stephen Warren wrote:
> On 10/31/2012 09:56 AM, Simon Glass wrote:
>> Hi Stephen,
>>
>> On Wed, Oct 31, 2012 at 8:41 AM, Stephen Warren<swarren at wwwdotorg.org>  wrote:
>>> On 10/31/2012 12:00 AM, Heiko Schocher wrote:
>>>> Hello Stephen,
>>>>
>>>> On 30.10.2012 23:32, Stephen Warren wrote:
>>>>> On 10/30/2012 11:28 AM, Simon Glass wrote:
> ...
>>>>>> diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h
> ...
>>>>>> +#define CONFIG_SYS_I2C
>>>>>> +#define CONFIG_SYS_I2C_ADAPTERS    {&tegra_i2c_adap[0]}
>>>>>> +#define CONFIG_SYS_NUM_I2C_ADAPTERS    TEGRA_I2C_NUM_CONTROLLERS
>>>>>
>>>>> But, why is CONFIG_SYS_I2C_ADAPTERS needed; can't the adapter init
>>>>> functions (which presumably would be called from board code or as a
>>>>> result of DT parsing) dynamically register themselves?
> ...
>>> I mainly ask because Simon is pushing to have Tegra's U-Boot completely
>>> driven by device tree. If we need to hard-code the list of enabled I2C
>>> adapters in the U-Boot config file, and don't also support dynamically
>>> added I2C drivers, then that will be incompatible with device tree.
>>
>> Mostly, although with the serial console (which had a similar problem)
>> we just decoded the information onto the stack as needed. It was
>> inefficient, but worked fine for a small number of operations. We
>> might be able to do better with pre-relocation malloc() soon.
>
> It's more complex than that.
>
> If we use DT, we must be able to:
>
> a) Configure exactly which I2C instances the board uses from DT.
> b) Provide configuration (e.g. max clock rate) for those instances from DT.
>
> If all in-use I2C adapters must be specified statically in
> CONFIG_SYS_I2C_ADAPTERS, then since a board's DT could enable any
> arbitrary subset of Tegra's I2C adapters, then we must always set
> CONFIG_SYS_I2C_ADAPTERS to the list of all Tegra's I2C adapters. If we
> put some subset into CONFIG_SYS_I2C_ADAPTERS, then we're pre-defining
> the maximal set of I2C adapters that a board can enable, which means DT
> isn't specifying that, but rather the board config file is, and hence
> it's pointless to even use DT for this purpose.

My current approach needs static specific adapters, yes. But I see not
the problem, if we define all tegra adapters per default and ...

> Now, most boards won't use all I2C adapters, so presumably the Tegra I2C
> init routine will look for status="disabled" (or the inverse) in DT, and
> only initialize if the DT node for the adapter is present and enabled.

... and it should here be possible to add the used "i2c busses"!
dynamically from the info in the DT, or?

We use in U-Boot not direct the i2c adapters, instead i2c busses ...
so if we define all 4 tegra i2c adapters per default, but using on
one board only adapter 1 and 3 we have two i2c busses:
0 (= adapter 1) and
1 (= adapter 3) ...
no gaps between ...)

> However, this will leave entries in CONFIG_SYS_I2C_ADAPTERS that are not
> enabled, which will presumably influence the I2C bus numbering in the

No, why? You can add all i2c adapters to the CONFIG_SYS_I2C_ADAPTERS
define, without really use them in CONFIG_SYS_I2C_BUSSES. And it
should be possible (not yet coded, but tried in an older version) to add
i2c busses after relocation, or while interpret DT ...

something like I did in
http://git.denx.de/?p=u-boot/u-boot-i2c.git;a=commitdiff;h=ccb680c8cf9002232bc459e4003e3b47db5e1bf4#patch13
function:
int i2c_add_one_bus(char *buf)

-> while interpreting DT i2c info for above board will result in calling:
    i2c_add_one_bus("tegra-i2c-1");
    i2c_add_one_bus("tegra-i2c-3");

and results in two new i2c busses 0 and 1 ...
Maybe this is a way to go?

> U-Boot shell; there will be I2C busses that exist but cannot be used. Is
> this what we want? Perhaps it is in fact a good idea to always make the

Now, this is wrong! You mix here "i2c bus" with "i2c adapter"! We have
some i2c adapters which are defined but (maybe) not used ...

> U-Boot shell's I2C bus IDs be the same as the HW's, and hence leave gaps
> when some ports aren't enabled? That would be a departure from the way
> USB is handled today though.

Hmm.. but is this possible? If we have a board with 2 (or more) different
i2c adapters (which is now possible with the new framework), for example
2 i2c soft adapters + 4 tegra i2c adapter ... if we say the i2c tegra
adapters are the first 4 i2c busses, so we cannot longer say the
two soft i2c adapters are starting from 0 too (and vice versa) ...

bye,
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany