[U-Boot] [PATCH 2/2] ARM: tegra: enable 8-bit SD slots in board files

Stephen Warren swarren at wwwdotorg.org
Fri Nov 2 17:56:13 CET 2012


From: Stephen Warren <swarren at nvidia.com>

Harmony contains an SD slot with all 8 bits routed. This allows plugging
in an eMMC-chip-in-SD-form-factor.

Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits
hooked up.

Now that the U-Boot eMMC code fully supports 8-bit operation, initialize
those ports as 8-bit instead of 4-bit to improve performance.

Whistler was already registering its ports as 8-bit.

TrimSlice doesn't have any 8-bit ports.

I don't have any Avionic Design boards nor the Colibri board to test with.

Signed-off-by: Stephen Warren <swarren at nvidia.com>
---
 board/compal/paz00/paz00.c       |    5 ++---
 board/nvidia/harmony/harmony.c   |    5 ++---
 board/nvidia/seaboard/seaboard.c |    5 ++---
 3 files changed, 6 insertions(+), 9 deletions(-)

diff --git a/board/compal/paz00/paz00.c b/board/compal/paz00/paz00.c
index 0725989..6492d41 100644
--- a/board/compal/paz00/paz00.c
+++ b/board/compal/paz00/paz00.c
@@ -61,9 +61,8 @@ int board_mmc_init(bd_t *bd)
 	pin_mux_mmc();
 
 	debug("board_mmc_init: init eMMC\n");
-	/* init dev 0, eMMC chip, with 4-bit bus */
-	/* The board has an 8-bit bus, but 8-bit doesn't work yet */
-	tegra_mmc_init(0, 4, -1, -1);
+	/* init dev 0, eMMC chip, with 8-bit bus */
+	tegra_mmc_init(0, 8, -1, -1);
 
 	debug("board_mmc_init: init SD slot\n");
 	/* init dev 3, SD slot, with 4-bit bus */
diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c
index c7590ac..93430ed 100644
--- a/board/nvidia/harmony/harmony.c
+++ b/board/nvidia/harmony/harmony.c
@@ -64,9 +64,8 @@ int board_mmc_init(bd_t *bd)
 	pin_mux_mmc();
 
 	debug("board_mmc_init: init SD slot J26\n");
-	/* init dev 0, SD slot J26, with 4-bit bus */
-	/* The board has an 8-bit bus, but 8-bit doesn't work yet */
-	tegra_mmc_init(0, 4, GPIO_PI6, GPIO_PH2);
+	/* init dev 0, SD slot J26, with 8-bit bus */
+	tegra_mmc_init(0, 8, GPIO_PI6, GPIO_PH2);
 
 	debug("board_mmc_init: init SD slot J5\n");
 	/* init dev 2, SD slot J5, with 4-bit bus */
diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c
index c412c07..3e33da0 100644
--- a/board/nvidia/seaboard/seaboard.c
+++ b/board/nvidia/seaboard/seaboard.c
@@ -71,9 +71,8 @@ int board_mmc_init(bd_t *bd)
 	pin_mux_mmc();
 
 	debug("board_mmc_init: init eMMC\n");
-	/* init dev 0, eMMC chip, with 4-bit bus */
-	/* The board has an 8-bit bus, but 8-bit doesn't work yet */
-	tegra_mmc_init(0, 4, -1, -1);
+	/* init dev 0, eMMC chip, with 8-bit bus */
+	tegra_mmc_init(0, 8, -1, -1);
 
 	debug("board_mmc_init: init SD slot\n");
 	/* init dev 1, SD slot, with 4-bit bus */
-- 
1.7.0.4



More information about the U-Boot mailing list