[U-Boot] [PATCH v2 01/13] mx31: Move EHCI definitions to ehci-fsl.h

stefano babic sbabic at denx.de
Sat Nov 10 17:45:29 CET 2012


Am 10/11/2012 13:37, schrieb Benoît Thébaudeau:
> Hi Stefano,
> 
> On Saturday, November 10, 2012 8:42:24 AM, Stefano Babic wrote:
>> On 08/11/2012 21:27, Benoît Thébaudeau wrote:
>>> The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so
>>> move them to
>>> ehci-fsl.h so that all MXC SoCs can use them.
>>>
>>> Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau at advansee.com>
>>> Cc: Marek Vasut <marex at denx.de>
>>> Cc: Stefano Babic <sbabic at denx.de>
>>> ---
>>
>> Hi Benoît,
>>
>>> Changes for v2: None.
>>>
>>>  .../arch/arm/include/asm/arch-mx31/imx-regs.h      |   26
>>>  --------------------
>>>  .../include/usb/ehci-fsl.h                         |   22
>>>  +++++++++++++++++
>>>  2 files changed, 22 insertions(+), 26 deletions(-)
>>>
>>
>> By applying this patchset I see several minor issues reported by
>> checkpatch:
>>
>> WARNING: line over 80 characters
>> #303: FILE: drivers/usb/host/ehci-mx5.c:43:
>> +#define MXC_OTG_UCTRL_OWIE_BIT		(1 << 27)	/* OTG wakeup intr enable
>> */
>>
>> WARNING: line over 80 characters
>> #305: FILE: drivers/usb/host/ehci-mx5.c:45:
>> +#define MXC_H1_UCTRL_H1UIE_BIT		(1 << 12)	/* Host1 ULPI interrupt
>> enable */
>>
>> WARNING: line over 80 characters
>> #306: FILE: drivers/usb/host/ehci-mx5.c:46:
>> +#define MXC_H1_UCTRL_H1WIE_BIT		(1 << 11)	/* HOST1 wakeup intr
>> enable */
>>
>> WARNING: line over 80 characters
>> #312: FILE: drivers/usb/host/ehci-mx5.c:50:
>> +#define MXC_OTG_PHYCTRL_OC_DIS_BIT	(1 << 8)	/* OTG Disable
>> Overcurrent
>> Event */
>>
>> WARNING: line over 80 characters
>> #313: FILE: drivers/usb/host/ehci-mx5.c:51:
>> +#define MXC_H1_OC_DIS_BIT		(1 << 5)	/* UH1 Disable Overcurrent Event
>> */
>>
>> WARNING: line over 80 characters
>> #343: FILE: drivers/usb/host/ehci-mx5.c:174:
>> +			v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask unused */
>>
>> WARNING: line over 80 characters
>> #352: FILE: drivers/usb/host/ehci-mx5.c:190:
>> +			v &= ~MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask unused */
>>
>> WARNING: line over 80 characters
>> #641: FILE: drivers/usb/host/ehci-mx5.c:47:
>> +#define MXC_OTG_UCTRL_O_PWR_POL_BIT	(1 << 24)	/* OTG power pin
>> polarity */
>>
>> WARNING: line over 80 characters
>> #645: FILE: drivers/usb/host/ehci-mx5.c:51:
>> +#define MXC_H1_UCTRL_H1_PWR_POL_BIT	(1 << 8)	/* HOST1 power pin
>> polarity */
>>
>> WARNING: line over 80 characters
>> #648: FILE: drivers/usb/host/ehci-mx5.c:54:
>> +#define MXC_OTG_PHYCTRL_OC_POL_BIT	(1 << 9)	/* OTG Polarity of
>> Overcurrent */
>>
>> WARNING: line over 80 characters
>> #650: FILE: drivers/usb/host/ehci-mx5.c:56:
>> +#define MXC_H1_OC_POL_BIT		(1 << 6)	/* UH1 Polarity of Overcurrent
>> */
>>
>> WARNING: line over 80 characters
>> #652: FILE: drivers/usb/host/ehci-mx5.c:58:
>> +#define MXC_OTG_PHYCTRL_PWR_POL_BIT	(1 << 3)	/* OTG Power Pin
>> Polarity */
>>
>> WARNING: line over 80 characters
>> #873: FILE: drivers/usb/host/ehci-mxc.c:85:
>> +			MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT |
>>
>> WARNING: line over 80 characters
>> #1078: FILE: drivers/usb/host/ehci-mxc.c:184:
>> +			MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT | MX35_H1_USBTE_BIT |
>>
>> WARNING: line over 80 characters
>> #1179: FILE: board/freescale/mx35pdk/mx35pdk.c:105:
>> +	mxc_request_iomux(MX35_PIN_USBOTG_PWR, MUX_CONFIG_SION |
>> MUX_CONFIG_FUNC);
>>
>> WARNING: line over 80 characters
>> #1180: FILE: board/freescale/mx35pdk/mx35pdk.c:106:
>> +	mxc_request_iomux(MX35_PIN_USBOTG_OC, MUX_CONFIG_SION |
>> MUX_CONFIG_FUNC);
>>
>> total: 0 errors, 16 warnings, 810 lines checked
>>
>> Can you fix them ? Thanks !
> 
> OK, I'll do that. For the #define-s, do you prefer that I move the comment to
> the previous line, or that I split the end of the comment to the next line?

I have no preference, I usually move the comment to the previous line,
but it is a question of taste ;-)

Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================


More information about the U-Boot mailing list