[U-Boot] [PATCH v3] powerpc/mpc85xx/p2020rdb-pca: Use L2 SRAM for SPL boot
Scott Wood
scottwood at freescale.com
Tue Nov 13 23:41:35 CET 2012
This allows DDR configuration to be deferred to the final U-Boot image,
which is able to make use of SPD data. The SPL itself cannot use SPD due
to code size constraints. It previously used fixed register values for
DDR configuration, and those values did not work on the p2020rdb-pca
board I tested with. It's possible that different revisions of the board
require different settings. Using SPD eliminates that problem.
Signed-off-by: Scott Wood <scottwood at freescale.com>
Cc: Andy Fleming <afleming at freescale.com>
---
v3: Fix a build break due to removal of fixed DDR defines -- this was a
last minute change in the previous patch, but I thought I had tested
it... :-P
v2: new patch in v2 of patchset
board/freescale/p1_p2_rdb_pc/ddr.c | 2 +
board/freescale/p1_p2_rdb_pc/spl_minimal.c | 7 ++-
board/freescale/p1_p2_rdb_pc/tlb.c | 15 +++++-
include/configs/p1_p2_rdb_pc.h | 69 +++++++++++++---------------
4 files changed, 54 insertions(+), 39 deletions(-)
diff --git a/board/freescale/p1_p2_rdb_pc/ddr.c b/board/freescale/p1_p2_rdb_pc/ddr.c
index 88ba56f..9355536 100644
--- a/board/freescale/p1_p2_rdb_pc/ddr.c
+++ b/board/freescale/p1_p2_rdb_pc/ddr.c
@@ -206,6 +206,7 @@ int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
}
#endif /* CONFIG_SYS_DDR_RAW_TIMING */
+#ifdef CONFIG_SYS_DDR_CS0_BNDS
/* Fixed sdram init -- doesn't use serial presence detect. */
phys_size_t fixed_sdram(void)
{
@@ -260,6 +261,7 @@ phys_size_t fixed_sdram(void)
return ddr_size;
}
+#endif
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
diff --git a/board/freescale/p1_p2_rdb_pc/spl_minimal.c b/board/freescale/p1_p2_rdb_pc/spl_minimal.c
index 5c893ee..d48fb01 100644
--- a/board/freescale/p1_p2_rdb_pc/spl_minimal.c
+++ b/board/freescale/p1_p2_rdb_pc/spl_minimal.c
@@ -23,16 +23,18 @@
#include <ns16550.h>
#include <asm/io.h>
#include <nand.h>
+#include <linux/compiler.h>
#include <asm/fsl_law.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
+#ifndef CONFIG_SYS_INIT_L2_ADDR
/*
* Fixed sdram init -- doesn't use serial presence detect.
*/
-void sdram_init(void)
+static void sdram_init(void)
{
ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR;
@@ -71,6 +73,7 @@ void sdram_init(void)
set_next_law(0, CONFIG_SYS_SDRAM_SIZE_LAW, LAW_TRGT_IF_DDR_1);
}
+#endif
void board_init_f(ulong bootflag)
{
@@ -101,8 +104,10 @@ void board_init_f(ulong bootflag)
__raw_writel(0x00000000, &pgpio->gpdir);
#endif
+#ifndef CONFIG_SYS_INIT_L2_ADDR
/* Initialize the DDR3 */
sdram_init();
+#endif
/* copy code to RAM and jump to it - this should not return */
/* NOTE - code has to be copied out of NAND buffer before
diff --git a/board/freescale/p1_p2_rdb_pc/tlb.c b/board/freescale/p1_p2_rdb_pc/tlb.c
index 0873dd7..3e4dffd 100644
--- a/board/freescale/p1_p2_rdb_pc/tlb.c
+++ b/board/freescale/p1_p2_rdb_pc/tlb.c
@@ -95,6 +95,16 @@ struct fsl_e_tlb_entry tlb_table[] = {
#endif
#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL)
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+ /* L2SRAM */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 8, BOOKE_PAGESZ_256K, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
+ CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_256K, 1),
+#else
/* *I*G - eSDHC/eSPI/NAND boot */
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
@@ -106,8 +116,9 @@ struct fsl_e_tlb_entry tlb_table[] = {
CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 9, BOOKE_PAGESZ_1G, 1),
-#endif
-#endif
+#endif /* P1020MBG */
+#endif /* not L2 SRAM */
+#endif /* RAMBOOT/SPL */
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index ba7a364..964bfcd 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -38,6 +38,7 @@
#define __SW_BOOT_MASK 0x03
#define __SW_BOOT_NOR 0xe4
#define __SW_BOOT_SD 0x54
+#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
#if defined(CONFIG_P1020UTM)
@@ -46,6 +47,7 @@
#define __SW_BOOT_MASK 0x03
#define __SW_BOOT_NOR 0xe0
#define __SW_BOOT_SD 0x50
+#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
#if defined(CONFIG_P1020RDB)
@@ -61,6 +63,7 @@
#define __SW_BOOT_SD 0x9c
#define __SW_BOOT_NAND 0xec
#define __SW_BOOT_PCIE 0x6c
+#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
#if defined(CONFIG_P1021RDB)
@@ -78,6 +81,7 @@
#define __SW_BOOT_SD 0x9c
#define __SW_BOOT_NAND 0xec
#define __SW_BOOT_PCIE 0x6c
+#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
#if defined(CONFIG_P1024RDB)
@@ -91,6 +95,7 @@
#define __SW_BOOT_SPI 0x08
#define __SW_BOOT_SD 0x04
#define __SW_BOOT_NAND 0x0c
+#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
#if defined(CONFIG_P1025RDB)
@@ -108,6 +113,7 @@
#define __SW_BOOT_SPI 0x08
#define __SW_BOOT_SD 0x04
#define __SW_BOOT_NAND 0x0c
+#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
#if defined(CONFIG_P2020RDB)
@@ -122,6 +128,14 @@
#define __SW_BOOT_SD 0x68 /* or 0x18 */
#define __SW_BOOT_NAND 0xe8
#define __SW_BOOT_PCIE 0xa8
+#define CONFIG_SYS_L2_SIZE (512 << 10)
+#endif
+
+#if CONFIG_SYS_L2_SIZE >= (512 << 10)
+/* must be 32-bit */
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
#endif
#ifdef CONFIG_SDCARD
@@ -149,14 +163,28 @@
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SYS_TEXT_BASE 0x00201000
#define CONFIG_SPL_TEXT_BASE 0xfffff000
#define CONFIG_SPL_MAX_SIZE (4 * 1024)
+
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+/* We multiply CONFIG_SPL_MAX_SIZE by two to leave some room for BSS. */
+#define CONFIG_SYS_TEXT_BASE 0xf8f82000
+#define CONFIG_SPL_RELOC_TEXT_BASE \
+ (CONFIG_SYS_INIT_L2_END - CONFIG_SPL_MAX_SIZE * 2)
+#define CONFIG_SPL_RELOC_STACK \
+ (CONFIG_SYS_INIT_L2_END - CONFIG_SPL_MAX_SIZE * 2)
+#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR)
+#define CONFIG_SYS_NAND_U_BOOT_START \
+ (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SPL_MAX_SIZE)
+#else
+#define CONFIG_SYS_TEXT_BASE 0x00201000
#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000
#define CONFIG_SPL_RELOC_STACK 0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) + CONFIG_SPL_MAX_SIZE)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE)
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
+#endif
+
+#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000)
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0
#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#endif
@@ -261,39 +289,7 @@
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
/* Default settings for DDR3 */
-#ifdef CONFIG_P2020RDB
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
-#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
-#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000
-#define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000
-#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000
-
-#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
-#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
-#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
-
-#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
-#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8645F607
-#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
-#define CONFIG_SYS_DDR_RCW_1 0x00000000
-#define CONFIG_SYS_DDR_RCW_2 0x00000000
-#define CONFIG_SYS_DDR_CONTROL 0xC7000000 /* Type = DDR3 */
-#define CONFIG_SYS_DDR_CONTROL_2 0x24401000
-#define CONFIG_SYS_DDR_TIMING_4 0x00220001
-#define CONFIG_SYS_DDR_TIMING_5 0x02401400
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00020000
-#define CONFIG_SYS_DDR_TIMING_0 0x00330104
-#define CONFIG_SYS_DDR_TIMING_1 0x6f6B4644
-#define CONFIG_SYS_DDR_TIMING_2 0x0FA88CCF
-#define CONFIG_SYS_DDR_CLK_CTRL 0x02000000
-#define CONFIG_SYS_DDR_MODE_1 0x00421422
-#define CONFIG_SYS_DDR_MODE_2 0x04000000
-#define CONFIG_SYS_DDR_INTERVAL 0x0C300100
-
-#else
+#ifndef CONFIG_P2020RDB
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
@@ -334,13 +330,14 @@
* 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable
* 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3)
* 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1
+ * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 512K cacheable
+ * (early boot only)
* 0xff80_0000 0xff80_7fff NAND flash 32K non-cacheable CS1/0
* 0xff98_0000 0xff98_ffff PMC 64K non-cacheable CS2
* 0xffa0_0000 0xffaf_ffff CPLD 1M non-cacheable CS3
* 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable CS2
* 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable
- * 0xffd8_0000 0xffdf_ffff L2 SRAM Up to 512K cacheable
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
*/
--
1.7.9.5
More information about the U-Boot
mailing list