[U-Boot] [PATCH v2] ARM: at91 series: increase size for u-boot and change bootargs

Bo Shen voice.shen at atmel.com
Tue Nov 27 02:28:06 CET 2012


Hi Andreas,

On 11/26/2012 18:59, Andreas Bießmann wrote:
> Dear Bo Shen,
>
> On 13.11.2012 02:58, Bo Shen wrote:
>> As to more features are added into the u-boot, which cause the u-boot
>> size larger than 0x40000 (256KiB), so increase the size for u-boot
>> through move offset of the u-boot environment. Or else, when execute
>> saveenv command, which will erase the end of the u-boot causing it can
>> not boot up again.
>>
>> Also, the linux kernel image is bigger than 2MiB, so change the bootcmd
>> as the same time.
>>
>> Signed-off-by: Bo Shen <voice.shen at atmel.com>
>> ---
>> Change since v1:
>>    change the bootargs as to the size of mainline linux kernel image size
>> ---
>>   include/configs/at91sam9260ek.h    |   17 ++++++++---------
>>   include/configs/at91sam9261ek.h    |   17 ++++++++---------
>>   include/configs/at91sam9263ek.h    |   15 ++++++++-------
>>   include/configs/at91sam9m10g45ek.h |   15 +++++++--------
>>   4 files changed, 31 insertions(+), 33 deletions(-)
>>
>> diff --git a/include/configs/at91sam9260ek.h b/include/configs/at91sam9260ek.h
>> index f921fac..905d5c5 100644
>> --- a/include/configs/at91sam9260ek.h
>> +++ b/include/configs/at91sam9260ek.h
>> @@ -210,16 +210,15 @@
>>
>>   /* bootstrap + u-boot + env + linux in nandflash */
>>   #define CONFIG_ENV_IS_IN_NAND	1
>> -#define CONFIG_ENV_OFFSET		0x60000
>> -#define CONFIG_ENV_OFFSET_REDUND	0x80000
>> +#define CONFIG_ENV_OFFSET		0xc0000
>> +#define CONFIG_ENV_OFFSET_REDUND	0x100000
>>   #define CONFIG_ENV_SIZE		0x20000		/* 1 sector = 128 kB */
>> -#define CONFIG_BOOTCOMMAND	"nand read 0x22000000 0xA0000 0x200000; bootm"
>> -#define CONFIG_BOOTARGS		"console=ttyS0,115200 "			\
>> -				"root=/dev/mtdblock5 "			\
>> -				"mtdparts=atmel_nand:128k(bootstrap)ro,"	\
>> -				"256k(uboot)ro,128k(env1)ro,"		\
>> -				"128k(env2)ro,2M(linux),-(root) "	\
>> -				"rw rootfstype=jffs2"
>> +#define CONFIG_BOOTCOMMAND	"nand read 0x22000000 0x200000 0x300000; bootm"
>> +#define CONFIG_BOOTARGS							\
>> +	"console=ttyS0,115200 earlyprintk "				\
>> +	"mtdparts=atmel_nand:"						\
>> +	"8M(bootstrap/uboot/kernel)ro,-(rootfs) "			\
>> +	"root=/dev/mtdblock1 rw rootfstype=jffs2"
>
> I personally prefer to change bootlaoder related stuff also from linux.
> With this change you can not access the env partition from linux
> therefore you can never use tools like fw_pritnenv/fw_setenv.
> Can you please change this to a reasonable configuration. I think
> current setups will require about 1 sector for bootstrap, 1 or 2 sectors
> for each env, about 4 to 6 sectors for u-boot, another bunch of sectors
> for linux and maybe some place to store a configuration blob (think of
> 'Falcon mode' or FDT).

Ok, I will consider this and prepare for the next version.
Thanks.

Best Regards,
Bo Shen



More information about the U-Boot mailing list