[U-Boot] [PATCH 4/4] Sound: I2S: Replacing I2S1 with I2S0 channel.
Dani Krishna Mohan
krishna.md at samsung.com
Wed Aug 7 07:47:58 CEST 2013
This patch makes required changes to make use
of I2S0 channel instead of I2S1 channel on exynos5250.
Signed-off-by: Dani Krishna Mohan <krishna.md at samsung.com>
---
arch/arm/include/asm/arch-exynos/i2s-regs.h | 6 ++++++
drivers/sound/samsung-i2s.c | 16 ++++++++++------
2 files changed, 16 insertions(+), 6 deletions(-)
diff --git a/arch/arm/include/asm/arch-exynos/i2s-regs.h b/arch/arm/include/asm/arch-exynos/i2s-regs.h
index 613b9b7..4a4a7a0 100644
--- a/arch/arm/include/asm/arch-exynos/i2s-regs.h
+++ b/arch/arm/include/asm/arch-exynos/i2s-regs.h
@@ -8,10 +8,12 @@
#ifndef __I2S_REGS_H__
#define __I2S_REGS_H__
+#define CON_RESET (1 << 31)
#define CON_TXFIFO_FULL (1 << 8)
#define CON_TXCH_PAUSE (1 << 4)
#define CON_ACTIVE (1 << 0)
+#define MOD_OP_CLK (3 << 30)
#define MOD_BLCP_SHIFT 24
#define MOD_BLCP_16BIT (0 << MOD_BLCP_SHIFT)
#define MOD_BLCP_8BIT (1 << MOD_BLCP_SHIFT)
@@ -24,6 +26,7 @@
#define MOD_BLC_MASK (3 << 13)
#define MOD_SLAVE (1 << 11)
+#define MOD_RCLKSRC (0 << 10)
#define MOD_MASK (3 << 8)
#define MOD_LR_LLOW (0 << 7)
#define MOD_LR_RLOW (1 << 7)
@@ -47,4 +50,7 @@
#define FIC_TXFLUSH (1 << 15)
#define FIC_RXFLUSH (1 << 7)
+#define PSREN (1 << 15)
+#define PSVAL (3 << 8)
+
#endif /* __I2S_REGS_H__ */
diff --git a/drivers/sound/samsung-i2s.c b/drivers/sound/samsung-i2s.c
index 49921e5..8e8a2bc 100644
--- a/drivers/sound/samsung-i2s.c
+++ b/drivers/sound/samsung-i2s.c
@@ -303,21 +303,25 @@ int i2s_tx_init(struct i2stx_info *pi2s_tx)
(struct i2s_reg *)pi2s_tx->base_address;
/* Initialize GPIO for I2s */
- exynos_pinmux_config(PERIPH_ID_I2S1, 0);
+ exynos_pinmux_config(PERIPH_ID_I2S0, 0);
/* Set EPLL Clock */
- ret = set_epll_clk(pi2s_tx->audio_pll_clk);
+ ret = set_epll_clk(pi2s_tx->samplingrate * pi2s_tx->rfs * 4);
if (ret != 0) {
debug("%s: epll clock set rate falied\n", __func__);
return -1;
}
- /* Select Clk Source for Audio1 */
+ /* Select Clk Source for Audio0 */
set_i2s_clk_source();
- /* Set Prescaler to get MCLK */
- set_i2s_clk_prescaler(pi2s_tx->audio_pll_clk,
- (pi2s_tx->samplingrate * (pi2s_tx->rfs)));
+ /*Reset the i2s module */
+ writel(CON_RESET, &i2s_reg->con);
+
+ writel(MOD_OP_CLK | MOD_RCLKSRC, &i2s_reg->mod);
+
+ /* set i2s prescaler */
+ writel(PSREN | PSVAL, &i2s_reg->psr);
/* Configure I2s format */
ret = i2s_set_fmt(i2s_reg, (SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
--
1.7.9.5
More information about the U-Boot
mailing list