[U-Boot] [PATCH 2/2] mxs: spi: Remove CONFIG_MXS_SPI_DMA_ENABLE
Marek Vasut
marex at denx.de
Sat Feb 2 07:10:41 CET 2013
The CONFIG_MXS_SPI_DMA_ENABLE is no longer relevant as the SPI DMA
has proven to work correctly. Remove this configuration option.
Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Fabio Estevam <fabio.estevam at freescale.com>
Cc: Otavio Salvador <otavio at ossystems.com.br>
Cc: Stefano Babic <sbabic at denx.de>
---
drivers/spi/mxs_spi.c | 16 ----------------
include/configs/m28evk.h | 1 -
include/configs/mx28evk.h | 1 -
3 files changed, 18 deletions(-)
NOTE: COMPILE TESTED ONLY!!! Someone please test before applying!
diff --git a/drivers/spi/mxs_spi.c b/drivers/spi/mxs_spi.c
index 5a737a1..ca87180 100644
--- a/drivers/spi/mxs_spi.c
+++ b/drivers/spi/mxs_spi.c
@@ -40,17 +40,6 @@
#define MXSSSP_SMALL_TRANSFER 512
-/*
- * CONFIG_MXS_SPI_DMA_ENABLE: Experimental mixed PIO/DMA support for MXS SPI
- * host. Use with utmost caution!
- *
- * Enabling this is not yet recommended since this
- * still doesn't support transfers to/from unaligned
- * addresses. Therefore this driver will not work
- * for example with saving environment. This is
- * caused by DMA alignment constraints on MXS.
- */
-
struct mxs_spi_slave {
struct spi_slave slave;
uint32_t max_khz;
@@ -347,12 +336,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
char dummy;
int write = 0;
char *data = NULL;
-
-#ifdef CONFIG_MXS_SPI_DMA_ENABLE
int dma = 1;
-#else
- int dma = 0;
-#endif
if (bitlen == 0) {
if (flags & SPI_XFER_END) {
diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h
index 1b51fe2..59a7be9 100644
--- a/include/configs/m28evk.h
+++ b/include/configs/m28evk.h
@@ -244,7 +244,6 @@
#ifdef CONFIG_CMD_SPI
#define CONFIG_HARD_SPI
#define CONFIG_MXS_SPI
-#define CONFIG_MXS_SPI_DMA_ENABLE
#define CONFIG_SPI_HALF_DUPLEX
#define CONFIG_DEFAULT_SPI_BUS 2
#define CONFIG_DEFAULT_SPI_CS 0
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
index 71447d9..6a46f3c 100644
--- a/include/configs/mx28evk.h
+++ b/include/configs/mx28evk.h
@@ -202,7 +202,6 @@
#ifdef CONFIG_CMD_SPI
#define CONFIG_HARD_SPI
#define CONFIG_MXS_SPI
-#define CONFIG_MXS_SPI_DMA_ENABLE
#define CONFIG_SPI_HALF_DUPLEX
#define CONFIG_DEFAULT_SPI_BUS 2
#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0
--
1.7.10.4
More information about the U-Boot
mailing list