[U-Boot] support all dataflash for at91sam9g20ek_2mmc

John Stile john at stilen.com
Thu Feb 14 16:20:05 CET 2013


I am using uboot-2013.01, with at91sam9g20ek_2mmc and I am trying to
build for dataflash, using at91bootstrap-1.16, and buildroot-2011.11

Initially I built for nand flash, with a patch to boards.cfg and
at91sam9260ek.c

This was fine if I used the reset button, but from a cold boot, startup
stopped after after at91bootstrap-1.16, and uboot never starts.

Now I am trying to build uboot for all dataflash, but I still see the
same behavior with uboot.

Uboot worked from dataflash when using uboot-1.3.6 (and patches from
atmel), but much has changed since then, so it is hard to figure out if
something from those patches is lost in the current uboot.  

What can I try next.

Bellow are the patches I applied so far.

boards.cfg: add target name
at91sam9g20ek_2mmc_nandflash,at91sam9g20ek_2mmc_dataflash_cs0,at91sam9g20ek_2mmc_dataflash_cs1

signed-off-by John Stile <john at stilen.com>

diff -ruNp a/boards.cfg b/boards.cfg
--- a/boards.cfg        2013-02-14 07:08:12.000000000 -0800
+++ b/boards.cfg        2013-02-13 18:09:32.000000000 -0800
@@ -91,7 +91,10 @@ at91sam9263ek_norflash       arm
 at91sam9263ek_norflash_boot  arm         arm926ejs   at91sam9263ek
atmel          at91
at91sam9263ek:AT91SAM9263,SYS_USE_BOOT_NORFLASH
 at91sam9g10ek_dataflash_cs0  arm         arm926ejs   at91sam9261ek
atmel          at91
at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS0
 at91sam9g10ek_dataflash_cs3  arm         arm926ejs   at91sam9261ek
atmel          at91
at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS3
+at91sam9g20ek_2mmc_dataflash_cs0 arm     arm926ejs   at91sam9260ek
atmel          at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_DATAFLASH_CS0
+at91sam9g20ek_2mmc_dataflash_cs1 arm     arm926ejs   at91sam9260ek
atmel          at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_DATAFLASH_CS1
 at91sam9g10ek_nandflash      arm         arm926ejs   at91sam9261ek
atmel          at91        at91sam9261ek:AT91SAM9G10,SYS_USE_NANDFLASH
+at91sam9g20ek_2mmc_nandflash arm         arm926ejs   at91sam9260ek
atmel          at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_NANDFLASH
 at91sam9g20ek_dataflash_cs0  arm         arm926ejs   at91sam9260ek
atmel          at91
at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS0
 at91sam9g20ek_dataflash_cs1  arm         arm926ejs   at91sam9260ek
atmel          at91
at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS1
 at91sam9g20ek_nandflash      arm         arm926ejs   at91sam9260ek
atmel          at91        at91sam9260ek:AT91SAM9G20,SYS_USE_NANDFLASH



board/atmel/at91sam9260ek/at91sam9260ek.c	Added ability to make buildroot with correct board type, to match kernel

signed-off-by John Stile <john at stilen.com>

diff -ruNp a/board/atmel/at91sam9260ek/at91sam9260ek.c b/board/atmel/at91sam9260ek/at91sam9260ek.c
--- a/board/atmel/at91sam9260ek/at91sam9260ek.c	2013-01-29 09:09:35.000000000 -0800
+++ b/board/atmel/at91sam9260ek/at91sam9260ek.c	2013-01-29 09:10:46.000000000 -0800
@@ -157,6 +157,10 @@
 
 int board_init(void)
 {
+#ifdef CONFIG_AT91SAM9G20EK_2MMC
+       /* arch number of AT91SAM9260EK-Board */
+       gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK_2MMC;
+#else
 #ifdef CONFIG_AT91SAM9G20EK
 	/* arch number of AT91SAM9260EK-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK;
@@ -164,6 +168,7 @@
 	/* arch number of AT91SAM9260EK-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9260EK;
 #endif
+#endif
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 



More information about the U-Boot mailing list