[U-Boot] [PATCH 4/4 V3] EXYNOS: Move files from board/samsung to arch/arm
Minkyu Kang
mk7.kang at samsung.com
Wed Jul 3 14:10:48 CEST 2013
On 02/07/13 22:12, Rajeshwari Shinde wrote:
> This patch performs the following:
>
> 1) Convert the assembly code for memory and clock initialization to C code.
> 2) Move the memory and clock init codes from board/samsung to arch/arm
> 3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
> the common lowlevel_init from assembly to C-code
> 4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
> 5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
> done in _main.
> 6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.
>
> TEST: Tested SD-MMC boot on SMDK5250 and Origen.
> Tested USB and SPI boot on SMDK5250
> Compile tested for SMDKV310.
>
> Signed-off-by: Rajeshwari Shinde <rajeshwari.s at samsung.com>
> ---
> Changes in V2:
> - Rebased on latest u-boot-samsung tree.
> - Incorporated review comments from Minkyu Kang.
> Changes in V3:
> - Optimised the mem_ctrl_init function for exynos4.
> - Removed magic numbers.
> arch/arm/cpu/armv7/exynos/Makefile | 17 +-
> .../arm/cpu/armv7/exynos}/clock_init.h | 0
> arch/arm/cpu/armv7/exynos/clock_init_exynos4.c | 94 +++++
> .../arm/cpu/armv7/exynos/clock_init_exynos5.c | 47 +--
> arch/arm/cpu/armv7/exynos/common_setup.h | 43 ++
> .../arm/cpu/armv7/exynos}/dmc_common.c | 7 +-
> .../arm/cpu/armv7/exynos}/dmc_init_ddr3.c | 19 +-
> arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c | 212 ++++++++++
> .../arm/cpu/armv7/exynos/exynos4_setup.h | 397 +++++++++----------
> .../arm/cpu/armv7/exynos/exynos5_setup.h | 28 +-
> arch/arm/cpu/armv7/exynos/lowlevel_init.c | 73 ++++
> .../arm/cpu/armv7/exynos}/spl_boot.c | 74 +++-
> arch/arm/include/asm/arch-exynos/cpu.h | 5 +-
> board/samsung/origen/Makefile | 11 +-
> board/samsung/origen/lowlevel_init.S | 357 -----------------
> board/samsung/origen/mem_setup.S | 421 --------------------
> board/samsung/origen/mmc_boot.c | 58 ---
> board/samsung/smdk5250/Makefile | 14 +-
> board/samsung/smdkv310/Makefile | 10 +-
> board/samsung/smdkv310/lowlevel_init.S | 414 -------------------
> board/samsung/smdkv310/mem_setup.S | 365 -----------------
> board/samsung/smdkv310/mmc_boot.c | 60 ---
> include/configs/exynos5250-dt.h | 8 +-
> include/configs/origen.h | 8 +-
> include/configs/smdkv310.h | 7 +-
> 25 files changed, 770 insertions(+), 1979 deletions(-)
> rename {board/samsung/smdk5250 => arch/arm/cpu/armv7/exynos}/clock_init.h (100%)
> create mode 100644 arch/arm/cpu/armv7/exynos/clock_init_exynos4.c
> rename board/samsung/smdk5250/clock_init.c => arch/arm/cpu/armv7/exynos/clock_init_exynos5.c (95%)
> create mode 100644 arch/arm/cpu/armv7/exynos/common_setup.h
> rename {board/samsung/smdk5250 => arch/arm/cpu/armv7/exynos}/dmc_common.c (97%)
> rename {board/samsung/smdk5250 => arch/arm/cpu/armv7/exynos}/dmc_init_ddr3.c (95%)
> create mode 100644 arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c
> rename board/samsung/origen/origen_setup.h => arch/arm/cpu/armv7/exynos/exynos4_setup.h (65%)
> rename board/samsung/smdk5250/setup.h => arch/arm/cpu/armv7/exynos/exynos5_setup.h (96%)
> create mode 100644 arch/arm/cpu/armv7/exynos/lowlevel_init.c
> rename {board/samsung/smdk5250 => arch/arm/cpu/armv7/exynos}/spl_boot.c (74%)
> delete mode 100644 board/samsung/origen/lowlevel_init.S
> delete mode 100644 board/samsung/origen/mem_setup.S
> delete mode 100644 board/samsung/origen/mmc_boot.c
> delete mode 100644 board/samsung/smdkv310/lowlevel_init.S
> delete mode 100644 board/samsung/smdkv310/mem_setup.S
> delete mode 100644 board/samsung/smdkv310/mmc_boot.c
>
> diff --git a/arch/arm/cpu/armv7/exynos/Makefile b/arch/arm/cpu/armv7/exynos/Makefile
> index b2f9152..4661155 100644
> --- a/arch/arm/cpu/armv7/exynos/Makefile
> +++ b/arch/arm/cpu/armv7/exynos/Makefile
> @@ -22,10 +22,19 @@ include $(TOPDIR)/config.mk
>
> LIB = $(obj)lib$(SOC).o
>
> -COBJS += clock.o power.o soc.o system.o pinmux.o tzpc.o
> -
> -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> -OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
> +COBJS-y += clock.o power.o soc.o system.o pinmux.o tzpc.o
> +
> +ifdef CONFIG_SPL_BUILD
> +COBJS-$(CONFIG_EXYNOS5) += clock_init_exynos5.o
> +COBJS-$(CONFIG_EXYNOS5) += dmc_common.o dmc_init_ddr3.o
> +COBJS-$(CONFIG_EXYNOS4210)+= dmc_init_exynos4.o clock_init_exynos4.o
> +COBJS-y += spl_boot.o
> +COBJS-y += lowlevel_init.o
> +endif
> +
> +COBJS := $(COBJS-y)
> +SRCS := $(COBJS:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS))
>
> all: $(obj).depend $(LIB)
>
> diff --git a/board/samsung/smdk5250/clock_init.h b/arch/arm/cpu/armv7/exynos/clock_init.h
> similarity index 100%
> rename from board/samsung/smdk5250/clock_init.h
> rename to arch/arm/cpu/armv7/exynos/clock_init.h
> diff --git a/arch/arm/cpu/armv7/exynos/clock_init_exynos4.c b/arch/arm/cpu/armv7/exynos/clock_init_exynos4.c
> new file mode 100644
> index 0000000..bee0b5c
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/exynos/clock_init_exynos4.c
> @@ -0,0 +1,94 @@
> +/*
> + * Clock Initialization for board based on EXYNOS4210
> + *
> + * Copyright (C) 2013 Samsung Electronics
> + * Rajeshwari Shinde <rajeshwari.s at samsung.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <config.h>
> +#include <version.h>
> +#include <asm/io.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/arch/clk.h>
> +#include <asm/arch/clock.h>
> +#include "common_setup.h"
> +#include "exynos4_setup.h"
> +
> +/*
> + * system_clock_init: Initialize core clock and bus clock.
> + * void system_clock_init(void)
> + */
> +void system_clock_init(void)
> +{
> + struct exynos4_clock *clk = (struct exynos4_clock *)EXYNOS4_CLOCK_BASE;
NAK.
> +
> + writel(CLK_SRC_CPU_VAL, &clk->src_cpu);
> +
> + sdelay(0x10000);
> +
> + writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
> + writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
> + writel(CLK_SRC_DMC_VAL, &clk->src_dmc);
> + writel(CLK_SRC_LEFTBUS_VAL, &clk->src_leftbus);
> + writel(CLK_SRC_RIGHTBUS_VAL, &clk->src_rightbus);
> + writel(CLK_SRC_FSYS_VAL, &clk->src_fsys);
> + writel(CLK_SRC_PERIL0_VAL, &clk->src_peril0);
> + writel(CLK_SRC_CAM_VAL, &clk->src_cam);
> + writel(CLK_SRC_MFC_VAL, &clk->src_mfc);
> + writel(CLK_SRC_G3D_VAL, &clk->src_g3d);
> + writel(CLK_SRC_LCD0_VAL, &clk->src_lcd0);
> +
> + sdelay(0x10000);
> +
> + writel(CLK_DIV_CPU0_VAL, &clk->div_cpu0);
> + writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
> + writel(CLK_DIV_DMC0_VAL, &clk->div_dmc0);
> + writel(CLK_DIV_DMC1_VAL, &clk->div_dmc1);
> + writel(CLK_DIV_LEFTBUS_VAL, &clk->div_leftbus);
> + writel(CLK_DIV_RIGHTBUS_VAL, &clk->div_rightbus);
> + writel(CLK_DIV_TOP_VAL, &clk->div_top);
> + writel(CLK_DIV_FSYS1_VAL, &clk->div_fsys1);
> + writel(CLK_DIV_FSYS2_VAL, &clk->div_fsys2);
> + writel(CLK_DIV_FSYS3_VAL, &clk->div_fsys3);
> + writel(CLK_DIV_PERIL0_VAL, &clk->div_peril0);
> + writel(CLK_DIV_CAM_VAL, &clk->div_cam);
> + writel(CLK_DIV_MFC_VAL, &clk->div_mfc);
> + writel(CLK_DIV_G3D_VAL, &clk->div_g3d);
> + writel(CLK_DIV_LCD0_VAL, &clk->div_lcd0);
> +
> + /* Set PLL locktime */
> + writel(PLL_LOCKTIME, &clk->apll_lock);
> + writel(PLL_LOCKTIME, &clk->mpll_lock);
> + writel(PLL_LOCKTIME, &clk->epll_lock);
> + writel(PLL_LOCKTIME, &clk->vpll_lock);
> +
> + writel(APLL_CON1_VAL, &clk->apll_con1);
> + writel(APLL_CON0_VAL, &clk->apll_con0);
> + writel(MPLL_CON1_VAL, &clk->mpll_con1);
> + writel(MPLL_CON0_VAL, &clk->mpll_con0);
> + writel(EPLL_CON1_VAL, &clk->epll_con1);
> + writel(EPLL_CON0_VAL, &clk->epll_con0);
> + writel(VPLL_CON1_VAL, &clk->vpll_con1);
> + writel(VPLL_CON0_VAL, &clk->vpll_con0);
> +
> + sdelay(0x30000);
> +}
> diff --git a/board/samsung/smdk5250/dmc_init_ddr3.c b/arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c
> similarity index 95%
> rename from board/samsung/smdk5250/dmc_init_ddr3.c
> rename to arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c
> index e050790..de54af8 100644
> --- a/board/samsung/smdk5250/dmc_init_ddr3.c
> +++ b/arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c
> @@ -27,7 +27,8 @@
> #include <asm/arch/clock.h>
> #include <asm/arch/cpu.h>
> #include <asm/arch/dmc.h>
> -#include "setup.h"
> +#include "common_setup.h"
> +#include "exynos5_setup.h"
> #include "clock_init.h"
>
> #define RDLVL_COMPLETE_TIMEOUT 10000
> @@ -40,7 +41,8 @@ static void reset_phy_ctrl(void)
> writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
> }
>
> -int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
> +int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
> + int reset)
> {
> unsigned int val;
> struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
> @@ -49,9 +51,10 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
>
> phy0_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY0_BASE;
> phy1_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY1_BASE;
NAK.
Please use function instead.
> - dmc = (struct exynos5_dmc *)EXYNOS5_DMC_CTRL_BASE;
> + dmc = (struct exynos5_dmc *)samsung_get_base_dmc0();
>
> - reset_phy_ctrl();
> + if (reset)
> + reset_phy_ctrl();
>
> /* Set Impedance Output Driver */
> val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
> @@ -100,14 +103,14 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
>
> /* Start DLL locking */
> writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
> - &phy0_ctrl->phy_con12);
> + &phy0_ctrl->phy_con12);
> writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
> - &phy1_ctrl->phy_con12);
> + &phy1_ctrl->phy_con12);
>
> update_reset_dll(dmc, DDR_MODE_DDR3);
>
> writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
> - &dmc->concontrol);
> + &dmc->concontrol);
>
> /* Memory Channel Inteleaving Size */
> writel(mem->iv_size, &dmc->ivcontrol);
> @@ -119,7 +122,7 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size)
>
> /* Precharge Configuration */
> writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
> - &dmc->prechconfig);
> + &dmc->prechconfig);
>
> /* Power Down mode Configuration */
> writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
> diff --git a/arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c b/arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c
> new file mode 100644
> index 0000000..636d84c
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c
> @@ -0,0 +1,212 @@
> +/*
> + * Memory setup for board based on EXYNOS4210
> + *
> + * Copyright (C) 2013 Samsung Electronics
> + * Rajeshwari Shinde <rajeshwari.s at samsung.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <config.h>
> +#include <asm/arch/dmc.h>
> +#include "common_setup.h"
> +#include "exynos4_setup.h"
> +
> +struct mem_timings mem = {
> + .direct_cmd_msr = {
> + DIRECT_CMD1, DIRECT_CMD2, DIRECT_CMD3, DIRECT_CMD4
> + },
> + .timingref = TIMINGREF_VAL,
> + .timingrow = TIMINGROW_VAL,
> + .timingdata = TIMINGDATA_VAL,
> + .timingpower = TIMINGPOWER_VAL,
> + .zqcontrol = ZQ_CONTROL_VAL,
> + .control0 = CONTROL0_VAL,
> + .control1 = CONTROL1_VAL,
> + .control2 = CONTROL2_VAL,
> + .concontrol = CONCONTROL_VAL,
> + .prechconfig = PRECHCONFIG,
> + .memcontrol = MEMCONTROL_VAL,
> + .memconfig0 = MEMCONFIG0_VAL,
> + .memconfig1 = MEMCONFIG1_VAL,
> + .dll_resync = FORCE_DLL_RESYNC,
> + .dll_on = DLL_CONTROL_ON,
> +};
> +static void phy_control_reset(int ctrl_no, struct exynos4_dmc *dmc)
> +{
> + if (ctrl_no) {
> + writel((mem.control1 | (1 << mem.dll_resync)),
> + &dmc->phycontrol1);
> + writel((mem.control1 | (0 << mem.dll_resync)),
> + &dmc->phycontrol1);
> + } else {
> + writel((mem.control0 | (0 << mem.dll_on)),
> + &dmc->phycontrol0);
> + writel((mem.control0 | (1 << mem.dll_on)),
> + &dmc->phycontrol0);
> + }
> +}
> +
> +static void dmc_config_mrs(struct exynos4_dmc *dmc, int chip)
> +{
> + int i;
> + unsigned long mask = 0;
> +
> + if (chip)
> + mask = DIRECT_CMD_CHIP1_SHIFT;
> +
> + for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
> + writel(mem.direct_cmd_msr[i] | mask,
> + &dmc->directcmd);
> + }
> +}
> +
> +static void dmc_init(struct exynos4_dmc *dmc)
> +{
> + /*
> + * DLL Parameter Setting:
> + * Termination: Enable R/W
> + * Phase Delay for DQS Cleaning: 180' Shift
> + */
> + writel(mem.control1, &dmc->phycontrol1);
> +
> + /*
> + * ZQ Calibration
> + * Termination: Disable
> + * Auto Calibration Start: Enable
> + */
> + writel(mem.zqcontrol, &dmc->phyzqcontrol);
> + sdelay(0x100000);
> +
> + /*
> + * Update DLL Information:
> + * Force DLL Resyncronization
> + */
> + phy_control_reset(1, dmc);
> + phy_control_reset(0, dmc);
> +
> + /* Set DLL Parameters */
> + writel(mem.control1, &dmc->phycontrol1);
> +
> + /* DLL Start */
> + writel((mem.control0 | CTRL_START | CTRL_DLL_ON), &dmc->phycontrol0);
> +
> + writel(mem.control2, &dmc->phycontrol2);
> +
> + /* Set Clock Ratio of Bus clock to Memory Clock */
> + writel(mem.concontrol, &dmc->concontrol);
> +
> + /*
> + * Memor Burst length: 8
> + * Number of chips: 2
> + * Memory Bus width: 32 bit
> + * Memory Type: DDR3
> + * Additional Latancy for PLL: 1 Cycle
> + */
> + writel(mem.memcontrol, &dmc->memcontrol);
> +
> + writel(mem.memconfig0, &dmc->memconfig0);
> + writel(mem.memconfig1, &dmc->memconfig1);
> +
> + /* Config Precharge Policy */
> + writel(mem.prechconfig, &dmc->prechconfig);
> + /*
> + * TimingAref, TimingRow, TimingData, TimingPower Setting:
> + * Values as per Memory AC Parameters
> + */
> + writel(mem.timingref, &dmc->timingref);
> + writel(mem.timingrow, &dmc->timingrow);
> + writel(mem.timingdata, &dmc->timingdata);
> + writel(mem.timingpower, &dmc->timingpower);
> +
> + /* Chip0: NOP Command: Assert and Hold CKE to high level */
> + writel(DIRECT_CMD_NOP, &dmc->directcmd);
> + sdelay(0x100000);
> +
> + /* Chip0: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
> + dmc_config_mrs(dmc, 0);
> + sdelay(0x100000);
> +
> + /* Chip0: ZQINIT */
> + writel(DIRECT_CMD_ZQ, &dmc->directcmd);
> + sdelay(0x100000);
> +
> + writel((DIRECT_CMD_NOP | DIRECT_CMD_CHIP1_SHIFT), &dmc->directcmd);
> + sdelay(0x100000);
> +
> + /* Chip1: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
> + dmc_config_mrs(dmc, 1);
> + sdelay(0x100000);
> +
> + /* Chip1: ZQINIT */
> + writel((DIRECT_CMD_ZQ | DIRECT_CMD_CHIP1_SHIFT), &dmc->directcmd);
> + sdelay(0x100000);
> +
> + phy_control_reset(1, dmc);
> + sdelay(0x100000);
> +
> + /* turn on DREX0, DREX1 */
> + writel((mem.concontrol | AREF_EN), &dmc->concontrol);
> +}
> +
> +void mem_ctrl_init(int reset)
> +{
> + struct exynos4_dmc *dmc;
> +
> + /*
> + * Async bridge configuration at CPU_core:
> + * 1: half_sync
> + * 0: full_sync
> + */
> + writel(1, ASYNC_CONFIG);
> +#ifdef CONFIG_ORIGEN
> + /* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0x7 */
> + writel(APB_SFR_INTERLEAVE_CONF_VAL, EXYNOS4_MIU_BASE +
> + APB_SFR_INTERLEAVE_CONF_OFFSET);
> + /* Update MIU Configuration */
> + writel(APB_SFR_ARBRITATION_CONF_VAL, EXYNOS4_MIU_BASE +
> + APB_SFR_ARBRITATION_CONF_OFFSET);
> +#else
> + writel(APB_SFR_INTERLEAVE_CONF_VAL, EXYNOS4_MIU_BASE +
> + APB_SFR_INTERLEAVE_CONF_OFFSET);
> + writel(INTERLEAVE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
> + ABP_SFR_INTERLEAVE_ADDRMAP_START_OFFSET);
> + writel(INTERLEAVE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
> + ABP_SFR_INTERLEAVE_ADDRMAP_END_OFFSET);
> + writel(INTERLEAVE_ADDR_MAP_EN, EXYNOS4_MIU_BASE +
> + ABP_SFR_SLV_ADDRMAP_CONF_OFFSET);
> +#ifdef CONFIG_MIU_LINEAR
> + writel(SLAVE0_SINGLE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
> + ABP_SFR_SLV0_SINGLE_ADDRMAP_START_OFFSET);
> + writel(SLAVE0_SINGLE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
> + ABP_SFR_SLV0_SINGLE_ADDRMAP_END_OFFSET);
> + writel(SLAVE1_SINGLE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
> + ABP_SFR_SLV1_SINGLE_ADDRMAP_START_OFFSET);
> + writel(SLAVE1_SINGLE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
> + ABP_SFR_SLV1_SINGLE_ADDRMAP_END_OFFSET);
> + writel(APB_SFR_SLV_ADDR_MAP_CONF_VAL, EXYNOS4_MIU_BASE +
> + ABP_SFR_SLV_ADDRMAP_CONF_OFFSET);
> +#endif
> +#endif
> + /* DREX0 */
> + dmc = (struct exynos4_dmc *)samsung_get_base_dmc0();
> + dmc_init(dmc);
> + dmc = (struct exynos4_dmc *)samsung_get_base_dmc1();
> + dmc_init(dmc);
> +}
> diff --git a/board/samsung/origen/origen_setup.h b/arch/arm/cpu/armv7/exynos/exynos4_setup.h
> similarity index 65%
> rename from board/samsung/origen/origen_setup.h
> rename to arch/arm/cpu/armv7/exynos/exynos4_setup.h
> index 926a4cc..6d25058 100644
> --- a/board/samsung/origen/origen_setup.h
> +++ b/arch/arm/cpu/armv7/exynos/exynos4_setup.h
> @@ -1,5 +1,5 @@
> /*
> - * Machine Specific Values for ORIGEN board based on S5PV310
> + * Machine Specific Values for EXYNOS4012 based board
> *
> * Copyright (C) 2011 Samsung Electronics
> *
> @@ -29,98 +29,22 @@
> #include <version.h>
> #include <asm/arch/cpu.h>
>
> -/* Offsets of clock registers (sources and dividers) */
> -#define CLK_SRC_CPU_OFFSET 0x14200
> -#define CLK_DIV_CPU0_OFFSET 0x14500
> -#define CLK_DIV_CPU1_OFFSET 0x14504
> -
> -#define CLK_SRC_DMC_OFFSET 0x10200
> -#define CLK_DIV_DMC0_OFFSET 0x10500
> -#define CLK_DIV_DMC1_OFFSET 0x10504
> -
> -#define CLK_SRC_TOP0_OFFSET 0xC210
> -#define CLK_SRC_TOP1_OFFSET 0xC214
> -#define CLK_DIV_TOP_OFFSET 0xC510
> -
> -#define CLK_SRC_LEFTBUS_OFFSET 0x4200
> -#define CLK_DIV_LEFTBUS_OFFSET 0x4500
> -
> -#define CLK_SRC_RIGHTBUS_OFFSET 0x8200
> -#define CLK_DIV_RIGHTBUS_OFFSET 0x8500
> -
> -#define CLK_SRC_FSYS_OFFSET 0xC240
> -#define CLK_DIV_FSYS1_OFFSET 0xC544
> -#define CLK_DIV_FSYS2_OFFSET 0xC548
> -#define CLK_DIV_FSYS3_OFFSET 0xC54C
> -
> -#define CLK_SRC_CAM_OFFSET 0xC220
> -#define CLK_SRC_TV_OFFSET 0xC224
> -#define CLK_SRC_MFC_OFFSET 0xC228
> -#define CLK_SRC_G3D_OFFSET 0xC22C
> -#define CLK_SRC_LCD0_OFFSET 0xC234
> -#define CLK_SRC_PERIL0_OFFSET 0xC250
> -
> -#define CLK_DIV_CAM_OFFSET 0xC520
> -#define CLK_DIV_TV_OFFSET 0xC524
> -#define CLK_DIV_MFC_OFFSET 0xC528
> -#define CLK_DIV_G3D_OFFSET 0xC52C
> -#define CLK_DIV_LCD0_OFFSET 0xC534
> -#define CLK_DIV_PERIL0_OFFSET 0xC550
> -
> -#define CLK_SRC_LCD0_OFFSET 0xC234
> -
> -#define APLL_LOCK_OFFSET 0x14000
> -#define MPLL_LOCK_OFFSET 0x14008
> -#define APLL_CON0_OFFSET 0x14100
> -#define APLL_CON1_OFFSET 0x14104
> -#define MPLL_CON0_OFFSET 0x14108
> -#define MPLL_CON1_OFFSET 0x1410C
> -
> -#define EPLL_LOCK_OFFSET 0xC010
> -#define VPLL_LOCK_OFFSET 0xC020
> -#define EPLL_CON0_OFFSET 0xC110
> -#define EPLL_CON1_OFFSET 0xC114
> -#define VPLL_CON0_OFFSET 0xC120
> -#define VPLL_CON1_OFFSET 0xC124
> -
> -/* DMC: DRAM Controllor Register offsets */
> -#define DMC_CONCONTROL 0x00
> -#define DMC_MEMCONTROL 0x04
> -#define DMC_MEMCONFIG0 0x08
> -#define DMC_MEMCONFIG1 0x0C
> -#define DMC_DIRECTCMD 0x10
> -#define DMC_PRECHCONFIG 0x14
> -#define DMC_PHYCONTROL0 0x18
> -#define DMC_PHYCONTROL1 0x1C
> -#define DMC_PHYCONTROL2 0x20
> -#define DMC_TIMINGAREF 0x30
> -#define DMC_TIMINGROW 0x34
> -#define DMC_TIMINGDATA 0x38
> -#define DMC_TIMINGPOWER 0x3C
> -#define DMC_PHYZQCONTROL 0x44
> +#ifdef CONFIG_CLK_800_330_165
> +#define DRAM_CLK_330
> +#endif
> +#ifdef CONFIG_CLK_1000_200_200
> +#define DRAM_CLK_200
> +#endif
> +#ifdef CONFIG_CLK_1000_330_165
> +#define DRAM_CLK_330
> +#endif
> +#ifdef CONFIG_CLK_1000_400_200
> +#define DRAM_CLK_400
> +#endif
>
> /* Bus Configuration Register Address */
> #define ASYNC_CONFIG 0x10010350
>
> -/* MIU Config Register Offsets*/
> -#define APB_SFR_INTERLEAVE_CONF_OFFSET 0x400
> -#define APB_SFR_ARBRITATION_CONF_OFFSET 0xC00
> -
> -/* Offset for inform registers */
> -#define INFORM0_OFFSET 0x800
> -#define INFORM1_OFFSET 0x804
> -
> -/* GPIO Offsets for UART: GPIO Contol Register */
> -#define EXYNOS4_GPIO_A0_CON_OFFSET 0x00
> -#define EXYNOS4_GPIO_A1_CON_OFFSET 0x20
> -
> -/* UART Register offsets */
> -#define ULCON_OFFSET 0x00
> -#define UCON_OFFSET 0x04
> -#define UFCON_OFFSET 0x08
> -#define UBRDIV_OFFSET 0x28
> -#define UFRACVAL_OFFSET 0x2C
> -
> /* CLK_SRC_CPU */
> #define MUX_HPM_SEL_MOUTAPLL 0x0
> #define MUX_HPM_SEL_SCLKMPLL 0x1
> @@ -485,123 +409,186 @@
> | (VPLL_MRR << 24) \
> | (VPLL_MFR << 16) \
> | (VPLL_K << 0))
> -/*
> - * UART GPIO_A0/GPIO_A1 Control Register Value
> - * 0x2: UART Function
> - */
> -#define EXYNOS4_GPIO_A0_CON_VAL 0x22222222
> -#define EXYNOS4_GPIO_A1_CON_VAL 0x222222
> -
> -/* ULCON: UART Line Control Value 8N1 */
> -#define WORD_LEN_5_BIT 0x00
> -#define WORD_LEN_6_BIT 0x01
> -#define WORD_LEN_7_BIT 0x02
> -#define WORD_LEN_8_BIT 0x03
> -
> -#define STOP_BIT_1 0x00
> -#define STOP_BIT_2 0x01
> -
> -#define NO_PARITY 0x00
> -#define ODD_PARITY 0x4
> -#define EVEN_PARITY 0x5
> -#define FORCED_PARITY_CHECK_AS_1 0x6
> -#define FORCED_PARITY_CHECK_AS_0 0x7
> -
> -#define INFRAMODE_NORMAL 0x00
> -#define INFRAMODE_INFRARED 0x01
> -
> -#define ULCON_VAL ((INFRAMODE_NORMAL << 6) \
> - | (NO_PARITY << 3) \
> - | (STOP_BIT_1 << 2) \
> - | (WORD_LEN_8_BIT << 0))
>
> -/*
> - * UCON: UART Control Value
> - * Tx_interrupt Type: Level
> - * Rx_interrupt Type: Level
> - * Rx Timeout Enabled: Yes
> - * Rx-Error Atatus_Int Enable: Yes
> - * Loop_Back: No
> - * Break Signal: No
> - * Transmit mode : Interrupt request/polling
> - * Receive mode : Interrupt request/polling
> - */
> -#define TX_PULSE_INTERRUPT 0
> -#define TX_LEVEL_INTERRUPT 1
> -#define RX_PULSE_INTERRUPT 0
> -#define RX_LEVEL_INTERRUPT 1
> -
> -#define RX_TIME_OUT ENABLE
> -#define RX_ERROR_STATE_INT_ENB ENABLE
> -#define LOOP_BACK DISABLE
> -#define BREAK_SIGNAL DISABLE
> -
> -#define TX_MODE_DISABLED 0X00
> -#define TX_MODE_IRQ_OR_POLL 0X01
> -#define TX_MODE_DMA 0X02
> -
> -#define RX_MODE_DISABLED 0X00
> -#define RX_MODE_IRQ_OR_POLL 0X01
> -#define RX_MODE_DMA 0X02
> -
> -#define UCON_VAL ((TX_LEVEL_INTERRUPT << 9) \
> - | (RX_LEVEL_INTERRUPT << 8) \
> - | (RX_TIME_OUT << 7) \
> - | (RX_ERROR_STATE_INT_ENB << 6) \
> - | (LOOP_BACK << 5) \
> - | (BREAK_SIGNAL << 4) \
> - | (TX_MODE_IRQ_OR_POLL << 2) \
> - | (RX_MODE_IRQ_OR_POLL << 0))
> +/* DMC */
> +#define DIRECT_CMD_NOP 0x07000000
> +#define DIRECT_CMD_ZQ 0x0a000000
> +#define DIRECT_CMD_CHIP1_SHIFT (1 << 20)
> +#define MEM_TIMINGS_MSR_COUNT 4
> +#define CTRL_START (1 << 0)
> +#define CTRL_DLL_ON (1 << 1)
> +#define AREF_EN (1 << 5)
> +#define DRV_TYPE (1 << 6)
> +
> +struct mem_timings {
> + unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
> + unsigned timingref;
> + unsigned timingrow;
> + unsigned timingdata;
> + unsigned timingpower;
> + unsigned zqcontrol;
> + unsigned control0;
> + unsigned control1;
> + unsigned control2;
> + unsigned concontrol;
> + unsigned prechconfig;
> + unsigned memcontrol;
> + unsigned memconfig0;
> + unsigned memconfig1;
> + unsigned dll_resync;
> + unsigned dll_on;
> +};
> +
> +/* MIU */
> +/* MIU Config Register Offsets*/
> +#define APB_SFR_INTERLEAVE_CONF_OFFSET 0x400
> +#define APB_SFR_ARBRITATION_CONF_OFFSET 0xC00
> +#define ABP_SFR_SLV_ADDRMAP_CONF_OFFSET 0x800
> +#define ABP_SFR_INTERLEAVE_ADDRMAP_START_OFFSET 0x808
> +#define ABP_SFR_INTERLEAVE_ADDRMAP_END_OFFSET 0x810
> +#define ABP_SFR_SLV0_SINGLE_ADDRMAP_START_OFFSET 0x818
> +#define ABP_SFR_SLV0_SINGLE_ADDRMAP_END_OFFSET 0x820
> +#define ABP_SFR_SLV1_SINGLE_ADDRMAP_START_OFFSET 0x828
> +#define ABP_SFR_SLV1_SINGLE_ADDRMAP_END_OFFSET 0x830
> +
> +#ifdef CONFIG_ORIGEN
> +/* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0x7 */
> +#define APB_SFR_INTERLEAVE_CONF_VAL 0x20001507
> +#define APB_SFR_ARBRITATION_CONF_VAL 0x00000001
> +#endif
>
> -/*
> - * UFCON: UART FIFO Control Value
> - * Tx FIFO Trigger LEVEL: 2 Bytes (001)
> - * Rx FIFO Trigger LEVEL: 2 Bytes (001)
> - * Tx Fifo Reset: No
> - * Rx Fifo Reset: No
> - * FIFO Enable: Yes
> - */
> -#define TX_FIFO_TRIGGER_LEVEL_0_BYTES 0x00
> -#define TX_FIFO_TRIGGER_LEVEL_2_BYTES 0x1
> -#define TX_FIFO_TRIGGER_LEVEL_4_BYTES 0x2
> -#define TX_FIFO_TRIGGER_LEVEL_6_BYTES 0x3
> -#define TX_FIFO_TRIGGER_LEVEL_8_BYTES 0x4
> -#define TX_FIFO_TRIGGER_LEVEL_10_BYTES 0x5
> -#define TX_FIFO_TRIGGER_LEVEL_12_BYTES 0x6
> -#define TX_FIFO_TRIGGER_LEVEL_14_BYTES 0x7
> -
> -#define RX_FIFO_TRIGGER_LEVEL_2_BYTES 0x0
> -#define RX_FIFO_TRIGGER_LEVEL_4_BYTES 0x1
> -#define RX_FIFO_TRIGGER_LEVEL_6_BYTES 0x2
> -#define RX_FIFO_TRIGGER_LEVEL_8_BYTES 0x3
> -#define RX_FIFO_TRIGGER_LEVEL_10_BYTES 0x4
> -#define RX_FIFO_TRIGGER_LEVEL_12_BYTES 0x5
> -#define RX_FIFO_TRIGGER_LEVEL_14_BYTES 0x6
> -#define RX_FIFO_TRIGGER_LEVEL_16_BYTES 0x7
> -
> -#define TX_FIFO_TRIGGER_LEVEL TX_FIFO_TRIGGER_LEVEL_2_BYTES
> -#define RX_FIFO_TRIGGER_LEVEL RX_FIFO_TRIGGER_LEVEL_4_BYTES
> -#define TX_FIFO_RESET DISABLE
> -#define RX_FIFO_RESET DISABLE
> -#define FIFO_ENABLE ENABLE
> -#define UFCON_VAL ((TX_FIFO_TRIGGER_LEVEL << 8) \
> - | (RX_FIFO_TRIGGER_LEVEL << 4) \
> - | (TX_FIFO_RESET << 2) \
> - | (RX_FIFO_RESET << 1) \
> - | (FIFO_ENABLE << 0))
> -/*
> - * Baud Rate Division Value
> - * 115200 BAUD:
> - * UBRDIV_VAL = SCLK_UART/((115200 * 16) - 1)
> - * UBRDIV_VAL = (800 MHz)/((115200 * 16) - 1)
> - */
> -#define UBRDIV_VAL 0x35
> +#define INTERLEAVE_ADDR_MAP_START_ADDR 0x40000000
> +#define INTERLEAVE_ADDR_MAP_END_ADDR 0xbfffffff
> +#define INTERLEAVE_ADDR_MAP_EN 0x00000001
>
> -/*
> - * Fractional Part of Baud Rate Divisor:
> - * 115200 BAUD:
> - * UBRFRACVAL = ((((SCLK_UART*10/(115200*16) -10))%10)*16/10)
> - * UBRFRACVAL = ((((800MHz*10/(115200*16) -10))%10)*16/10)
> - */
> -#define UFRACVAL_VAL 0x4
> +#ifdef CONFIG_MIU_1BIT_INTERLEAVED
> +/* Interleave_bit0: 0xC*/
> +#define APB_SFR_INTERLEAVE_CONF_VAL 0x0000000c
> +#endif
> +#ifdef CONFIG_MIU_2BIT_INTERLEAVED
> +/* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0xc */
> +#define APB_SFR_INTERLEAVE_CONF_VAL 0x2000150c
> +#endif
> +#define SLAVE0_SINGLE_ADDR_MAP_START_ADDR 0x40000000
> +#define SLAVE0_SINGLE_ADDR_MAP_END_ADDR 0x7fffffff
> +#define SLAVE1_SINGLE_ADDR_MAP_START_ADDR 0x80000000
> +#define SLAVE1_SINGLE_ADDR_MAP_END_ADDR 0xbfffffff
> +/* Enable SME0 and SME1*/
> +#define APB_SFR_SLV_ADDR_MAP_CONF_VAL 0x00000006
> +
> +#define FORCE_DLL_RESYNC 3
> +#define DLL_CONTROL_ON 1
> +
> +#define DIRECT_CMD1 0x00020000
> +#define DIRECT_CMD2 0x00030000
> +#define DIRECT_CMD3 0x00010002
> +#define DIRECT_CMD4 0x00000328
> +
> +#define CTRL_ZQ_MODE_NOTERM (0x1 << 0)
> +#define CTRL_ZQ_START (0x1 << 1)
> +#define CTRL_ZQ_DIV (0 << 4)
> +#define CTRL_ZQ_MODE_DDS (0x7 << 8)
> +#define CTRL_ZQ_MODE_TERM (0x2 << 11)
> +#define CTRL_ZQ_FORCE_IMPN (0x5 << 14)
> +#define CTRL_ZQ_FORCE_IMPP (0x6 << 17)
> +#define CTRL_DCC (0xE38 << 20)
> +#define ZQ_CONTROL_VAL (CTRL_ZQ_MODE_NOTERM | CTRL_ZQ_START\
> + | CTRL_ZQ_DIV | CTRL_ZQ_MODE_DDS\
> + | CTRL_ZQ_MODE_TERM | CTRL_ZQ_FORCE_IMPN\
> + | CTRL_ZQ_FORCE_IMPP | CTRL_DCC)
> +
> +#define ASYNC (0 << 0)
> +#define CLK_RATIO (1 << 1)
> +#define DIV_PIPE (1 << 3)
> +#define AWR_ON (1 << 4)
> +#define AREF_DISABLE (0 << 5)
> +#define DRV_TYPE_DISABLE (0 << 6)
> +#define CHIP0_NOT_EMPTY (0 << 8)
> +#define CHIP1_NOT_EMPTY (0 << 9)
> +#define DQ_SWAP_DISABLE (0 << 10)
> +#define QOS_FAST_DISABLE (0 << 11)
> +#define RD_FETCH (0x3 << 12)
> +#define TIMEOUT_LEVEL0 (0xFFF << 16)
> +#define CONCONTROL_VAL (ASYNC | CLK_RATIO | DIV_PIPE | AWR_ON\
> + | AREF_DISABLE | DRV_TYPE_DISABLE\
> + | CHIP0_NOT_EMPTY | CHIP1_NOT_EMPTY\
> + | DQ_SWAP_DISABLE | QOS_FAST_DISABLE\
> + | RD_FETCH | TIMEOUT_LEVEL0)
> +
> +#define CLK_STOP_DISABLE (0 << 1)
> +#define DPWRDN_DISABLE (0 << 2)
> +#define DPWRDN_TYPE (0 << 3)
> +#define TP_DISABLE (0 << 4)
> +#define DSREF_DIABLE (0 << 5)
> +#define ADD_LAT_PALL (1 << 6)
> +#define MEM_TYPE_DDR3 (0x6 << 8)
> +#define MEM_WIDTH_32 (0x2 << 12)
> +#define NUM_CHIP_2 (1 << 16)
> +#define BL_8 (0x3 << 20)
> +#define MEMCONTROL_VAL (CLK_STOP_DISABLE | DPWRDN_DISABLE\
> + | DPWRDN_TYPE | TP_DISABLE | DSREF_DIABLE\
> + | ADD_LAT_PALL | MEM_TYPE_DDR3 | MEM_WIDTH_32\
> + | NUM_CHIP_2 | BL_8)
> +
> +
> +#define CHIP_BANK_8 (0x3 << 0)
> +#define CHIP_ROW_14 (0x2 << 4)
> +#define CHIP_COL_10 (0x3 << 8)
> +#define CHIP_MAP_INTERLEAVED (1 << 12)
> +#define CHIP_MASK (0xe0 << 16)
> +#ifdef CONFIG_MIU_LINEAR
> +#define CHIP0_BASE (0x40 << 24)
> +#define CHIP1_BASE (0x60 << 24)
> +#else
> +#define CHIP0_BASE (0x20 << 24)
> +#define CHIP1_BASE (0x40 << 24)
> +#endif
> +#define MEMCONFIG0_VAL (CHIP_BANK_8 | CHIP_ROW_14 | CHIP_COL_10\
> + | CHIP_MAP_INTERLEAVED | CHIP_MASK | CHIP0_BASE)
> +#define MEMCONFIG1_VAL (CHIP_BANK_8 | CHIP_ROW_14 | CHIP_COL_10\
> + | CHIP_MAP_INTERLEAVED | CHIP_MASK | CHIP1_BASE)
> +
> +#define TP_CNT (0xff << 24)
> +#define PRECHCONFIG TP_CNT
> +
> +#define CTRL_OFF (0 << 0)
> +#define CTRL_DLL_OFF (0 << 1)
> +#define CTRL_HALF (0 << 2)
> +#define CTRL_DFDQS (1 << 3)
> +#define DQS_DELAY (0 << 4)
> +#define CTRL_START_POINT (0x10 << 8)
> +#define CTRL_INC (0x10 << 16)
> +#define CTRL_FORCE (0x71 << 24)
> +#define CONTROL0_VAL (CTRL_OFF | CTRL_DLL_OFF | CTRL_HALF\
> + | CTRL_DFDQS | DQS_DELAY | CTRL_START_POINT\
> + | CTRL_INC | CTRL_FORCE)
> +
> +#define CTRL_SHIFTC (0x6 << 0)
> +#define CTRL_REF (8 << 4)
> +#define CTRL_SHGATE (1 << 29)
> +#define TERM_READ_EN (1 << 30)
> +#define TERM_WRITE_EN (1 << 31)
> +#define CONTROL1_VAL (CTRL_SHIFTC | CTRL_REF | CTRL_SHGATE\
> + | TERM_READ_EN | TERM_WRITE_EN)
> +
> +#define CONTROL2_VAL 0x00000000
> +
> +#ifdef CONFIG_ORIGEN
> +#define TIMINGREF_VAL 0x000000BB
> +#define TIMINGROW_VAL 0x4046654f
> +#define TIMINGDATA_VAL 0x46400506
> +#define TIMINGPOWER_VAL 0x52000A3C
> +#else
> +#define TIMINGREF_VAL 0x000000BC
> +#ifdef DRAM_CLK_330
> +#define TIMINGROW_VAL 0x3545548d
> +#define TIMINGDATA_VAL 0x45430506
> +#define TIMINGPOWER_VAL 0x4439033c
> +#endif
> +#ifdef DRAM_CLK_400
> +#define TIMINGROW_VAL 0x45430506
> +#define TIMINGDATA_VAL 0x56500506
> +#define TIMINGPOWER_VAL 0x5444033d
> +#endif
> +#endif
> #endif
> diff --git a/board/samsung/smdk5250/setup.h b/arch/arm/cpu/armv7/exynos/exynos5_setup.h
> similarity index 96%
> rename from board/samsung/smdk5250/setup.h
> rename to arch/arm/cpu/armv7/exynos/exynos5_setup.h
> index eb91d13..8f36c16 100644
> --- a/board/samsung/smdk5250/setup.h
> +++ b/arch/arm/cpu/armv7/exynos/exynos5_setup.h
> @@ -93,17 +93,17 @@
> #define DMC_MEMCONTROL_MRR_BYTE_31_24 (3 << 25)
>
> /* MEMCONFIG0 register bit fields */
> -#define DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED (1 << 12)
> -#define DMC_MEMCONFIGx_CHIP_COL_10 (3 << 8)
> -#define DMC_MEMCONFIGx_CHIP_ROW_14 (2 << 4)
> -#define DMC_MEMCONFIGx_CHIP_ROW_15 (3 << 4)
> -#define DMC_MEMCONFIGx_CHIP_BANK_8 (3 << 0)
> -
> -#define DMC_MEMBASECONFIGx_CHIP_BASE(x) (x << 16)
> -#define DMC_MEMBASECONFIGx_CHIP_MASK(x) (x << 0)
> +#define DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED (1 << 12)
> +#define DMC_MEMCONFIGX_CHIP_COL_10 (3 << 8)
> +#define DMC_MEMCONFIGX_CHIP_ROW_14 (2 << 4)
> +#define DMC_MEMCONFIGX_CHIP_ROW_15 (3 << 4)
> +#define DMC_MEMCONFIGX_CHIP_BANK_8 (3 << 0)
> +
> +#define DMC_MEMBASECONFIGX_CHIP_BASE(x) (x << 16)
> +#define DMC_MEMBASECONFIGX_CHIP_MASK(x) (x << 0)
> #define DMC_MEMBASECONFIG_VAL(x) ( \
> - DMC_MEMBASECONFIGx_CHIP_BASE(x) | \
> - DMC_MEMBASECONFIGx_CHIP_MASK(0x780) \
> + DMC_MEMBASECONFIGX_CHIP_BASE(x) | \
> + DMC_MEMBASECONFIGX_CHIP_MASK(0x780) \
> )
>
> #define DMC_MEMBASECONFIG0_VAL DMC_MEMBASECONFIG_VAL(0x40)
> @@ -513,9 +513,11 @@ enum {
> * which the DMC uses to decide how to split a memory
> * chunk into smaller chunks to support concurrent
> * accesses; may vary across boards.
> + * @param reset Reset DDR PHY during initialization.
> * @return 0 if ok, SETUP_ERR_... if there is a problem
> */
> -int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size);
> +int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
> + int reset);
>
> /*
> * Configure ZQ I/O interface
> @@ -562,8 +564,4 @@ void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc);
> * @param ddr_mode Type of DDR memory
> */
> void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
> -
> -void sdelay(unsigned long);
> -void mem_ctrl_init(void);
> -void system_clock_init(void);
> #endif
> diff --git a/arch/arm/cpu/armv7/exynos/lowlevel_init.c b/arch/arm/cpu/armv7/exynos/lowlevel_init.c
> new file mode 100644
> index 0000000..11fe5b8
> --- /dev/null
> +++ b/arch/arm/cpu/armv7/exynos/lowlevel_init.c
> @@ -0,0 +1,73 @@
> +/*
> + * Lowlevel setup for EXYNOS5 based board
> + *
> + * Copyright (C) 2013 Samsung Electronics
> + * Rajeshwari Shinde <rajeshwari.s at samsung.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#include <common.h>
> +#include <config.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/arch/dmc.h>
> +#include <asm/arch/power.h>
> +#include <asm/arch/tzpc.h>
> +#include <asm/arch/periph.h>
> +#include <asm/arch/pinmux.h>
> +#include "common_setup.h"
> +
> +/* These are the things we can do during low-level init */
> +enum {
> + DO_WAKEUP = 1 << 0,
> + DO_CLOCKS = 1 << 1,
> + DO_MEM_RESET = 1 << 2,
> + DO_UART = 1 << 3,
> +};
> +
> +int do_lowlevel_init(void)
> +{
> + uint32_t reset_status;
> + int actions = 0;
> +
> + arch_cpu_init();
> +
> + reset_status = get_reset_status();
> +
> + switch (reset_status) {
> + case S5P_CHECK_SLEEP:
> + actions = DO_CLOCKS | DO_WAKEUP;
> + break;
> + case S5P_CHECK_DIDLE:
> + case S5P_CHECK_LPA:
> + actions = DO_WAKEUP;
> + break;
> + default:
> + /* This is a normal boot (not a wake from sleep) */
> + actions = DO_CLOCKS | DO_MEM_RESET;
> + }
> +
> + if (actions & DO_CLOCKS) {
> + system_clock_init();
> + mem_ctrl_init(actions & DO_MEM_RESET);
> + tzpc_init();
> + }
> +
> + return actions & DO_WAKEUP;
> +}
> diff --git a/board/samsung/smdk5250/spl_boot.c b/arch/arm/cpu/armv7/exynos/spl_boot.c
> similarity index 74%
> rename from board/samsung/smdk5250/spl_boot.c
> rename to arch/arm/cpu/armv7/exynos/spl_boot.c
> index 83275f1..6e8dd3b 100644
> --- a/board/samsung/smdk5250/spl_boot.c
> +++ b/arch/arm/cpu/armv7/exynos/spl_boot.c
> @@ -23,13 +23,18 @@
> #include<common.h>
> #include<config.h>
>
> -#include <asm/arch-exynos/dmc.h>
> #include <asm/arch/clock.h>
> #include <asm/arch/clk.h>
> +#include <asm/arch/dmc.h>
> +#include <asm/arch/power.h>
> #include <asm/arch/spl.h>
>
> +#include "common_setup.h"
> #include "clock_init.h"
>
> +DECLARE_GLOBAL_DATA_PTR;
> +#define OM_STAT (0x1f << 1)
> +
> /* Index into irom ptr table */
> enum index {
> MMC_INDEX,
> @@ -54,6 +59,7 @@ void *get_irom_func(int index)
> return (void *)*(u32 *)irom_ptr_table[index];
> }
>
> +#ifdef CONFIG_USB_BOOTING
> /*
> * Set/clear program flow prediction and return the previous state.
> */
> @@ -67,6 +73,7 @@ static int config_branch_prediction(int set_cr_z)
>
> return cr & CR_Z;
> }
> +#endif
>
> /*
> * Copy U-boot from mmc to RAM:
> @@ -75,35 +82,42 @@ static int config_branch_prediction(int set_cr_z)
> */
> void copy_uboot_to_ram(void)
> {
> - int is_cr_z_set;
> - unsigned int sec_boot_check;
> enum boot_mode bootmode = BOOT_MODE_OM;
>
> - u32 (*spi_copy)(u32 offset, u32 nblock, u32 dst);
> - u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst);
> + u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst) = NULL;
> + u32 offset = 0, size = 0;
> +#ifdef CONFIG_SUPPORT_EMMC_BOOT
> u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst);
> void (*end_bootop_from_emmc)(void);
> +#endif
> +#ifdef CONFIG_USB_BOOTING
> u32 (*usb_copy)(void);
> + int is_cr_z_set;
> + unsigned int sec_boot_check;
>
> /* Read iRAM location to check for secondary USB boot mode */
> sec_boot_check = readl(EXYNOS_IRAM_SECONDARY_BASE);
> if (sec_boot_check == EXYNOS_USB_SECONDARY_BOOT)
> bootmode = BOOT_MODE_USB;
> +#endif
>
> if (bootmode == BOOT_MODE_OM)
> - bootmode = readl(EXYNOS5_POWER_BASE) & OM_STAT;
> + bootmode = readl(samsung_get_base_power()) & OM_STAT;
>
> switch (bootmode) {
> +#ifdef CONFIG_SPI_BOOTING
> case BOOT_MODE_SERIAL:
> - spi_copy = get_irom_func(SPI_INDEX);
> - spi_copy(SPI_FLASH_UBOOT_POS, CONFIG_BL2_SIZE,
> - CONFIG_SYS_TEXT_BASE);
> + offset = SPI_FLASH_UBOOT_POS;
> + size = CONFIG_BL2_SIZE;
> + copy_bl2 = get_irom_func(SPI_INDEX);
> break;
> +#endif
> case BOOT_MODE_MMC:
> + offset = BL2_START_OFFSET;
> + size = BL2_SIZE_BLOC_COUNT;
> copy_bl2 = get_irom_func(MMC_INDEX);
> - copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT,
> - CONFIG_SYS_TEXT_BASE);
> break;
> +#ifdef CONFIG_SUPPORT_EMMC_BOOT
> case BOOT_MODE_EMMC:
> /* Set the FSYS1 clock divisor value for EMMC boot */
> emmc_boot_clk_div_set();
> @@ -114,6 +128,8 @@ void copy_uboot_to_ram(void)
> copy_bl2_from_emmc(BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
> end_bootop_from_emmc();
> break;
> +#endif
> +#ifdef CONFIG_USB_BOOTING
> case BOOT_MODE_USB:
> /*
> * iROM needs program flow prediction to be disabled
> @@ -124,14 +140,50 @@ void copy_uboot_to_ram(void)
> usb_copy();
> config_branch_prediction(is_cr_z_set);
> break;
> +#endif
> default:
> break;
> }
> +
> + if (copy_bl2)
> + copy_bl2(offset, size, CONFIG_SYS_TEXT_BASE);
> +}
> +
> +void memzero(void *s, size_t n)
> +{
> + char *ptr = s;
> + size_t i;
> +
> + for (i = 0; i < n; i++)
> + *ptr++ = '\0';
> +}
> +
> +/**
> + * Set up the U-Boot global_data pointer
> + *
> + * This sets the address of the global data, and sets up basic values.
> + *
> + * @param gdp Value to give to gd
> + */
> +static void setup_global_data(gd_t *gdp)
> +{
> + gd = gdp;
> + memzero((void *)gd, sizeof(gd_t));
> + gd->flags |= GD_FLG_RELOC;
> + gd->baudrate = CONFIG_BAUDRATE;
> + gd->have_console = 1;
> }
>
> void board_init_f(unsigned long bootflag)
> {
> + __aligned(8) gd_t local_gd;
> __attribute__((noreturn)) void (*uboot)(void);
> +
> + setup_global_data(&local_gd);
> +
> + if (do_lowlevel_init())
> + power_exit_wakeup();
> +
> copy_uboot_to_ram();
>
> /* Jump to U-Boot image */
> diff --git a/arch/arm/include/asm/arch-exynos/cpu.h b/arch/arm/include/asm/arch-exynos/cpu.h
> index 36b98c8..75dbe26 100644
> --- a/arch/arm/include/asm/arch-exynos/cpu.h
> +++ b/arch/arm/include/asm/arch-exynos/cpu.h
> @@ -115,7 +115,7 @@
> #define EXYNOS5_DMC_PHY0_BASE 0x10C00000
> #define EXYNOS5_DMC_PHY1_BASE 0x10C10000
maybe it can be dmc0 and dmc1
If you want to keep the interface with exynos4.
> #define EXYNOS5_GPIO_PART3_BASE 0x10D10000
> -#define EXYNOS5_DMC_CTRL_BASE 0x10DD0000
> +#define EXYNOS5_DMC0_BASE 0x10DD0000
why?
> #define EXYNOS5_GPIO_PART1_BASE 0x11400000
> #define EXYNOS5_MIPI_DSIM_BASE 0x11D00000
> #define EXYNOS5_USB_HOST_EHCI_BASE 0x12110000
> @@ -135,6 +135,7 @@
>
> #define EXYNOS5_ADC_BASE DEVICE_NOT_AVAILABLE
> #define EXYNOS5_MODEM_BASE DEVICE_NOT_AVAILABLE
> +#define EXYNOS5_DMC1_BASE DEVICE_NOT_AVAILABLE
It looks weird.
>
> #ifndef __ASSEMBLY__
> #include <asm/io.h>
> @@ -237,6 +238,8 @@ SAMSUNG_BASE(power, POWER_BASE)
> SAMSUNG_BASE(spi, SPI_BASE)
> SAMSUNG_BASE(spi_isp, SPI_ISP_BASE)
> SAMSUNG_BASE(tzpc, TZPC_BASE)
> +SAMSUNG_BASE(dmc0, DMC0_BASE)
> +SAMSUNG_BASE(dmc1, DMC1_BASE)
> #endif
>
> #endif /* _EXYNOS4_CPU_H */
> diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
> index 6c7a052..b32d1bd 100644
> --- a/include/configs/exynos5250-dt.h
> +++ b/include/configs/exynos5250-dt.h
> @@ -104,6 +104,7 @@
>
>
> #define CONFIG_BOARD_EARLY_INIT_F
> +#define CONFIG_SKIP_LOWLEVEL_INIT
>
> /* PWM */
> #define CONFIG_PWM
> @@ -137,6 +138,7 @@
> #define CONFIG_USB_STORAGE
>
> /* USB boot mode */
> +#define CONFIG_USB_BOOTING
> #define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070
> #define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002
> #define EXYNOS_IRAM_SECONDARY_BASE 0x02020018
> @@ -152,6 +154,8 @@
> #define CONFIG_SPL
> #define COPY_BL2_FNPTR_ADDR 0x02020030
>
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +
> /* specific .lds file */
> #define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
> #define CONFIG_SPL_TEXT_BASE 0x02023400
> @@ -229,7 +233,7 @@
> #define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512)
> #define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512)
>
> -#define OM_STAT (0x1f << 1)
> +#define CONFIG_SPI_BOOTING
> #define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058
> #define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
>
> @@ -241,7 +245,7 @@
>
> #define CONFIG_IRAM_STACK 0x02050000
>
> -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000)
> +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_IRAM_STACK
>
> /* I2C */
> #define CONFIG_SYS_I2C_INIT_BOARD
> diff --git a/include/configs/origen.h b/include/configs/origen.h
> index f71a463..fd7d667 100644
> --- a/include/configs/origen.h
> +++ b/include/configs/origen.h
> @@ -68,6 +68,8 @@
> #define CONFIG_BAUDRATE 115200
> #define EXYNOS4_DEFAULT_UART_OFFSET 0x020000
>
> +#define CONFIG_SKIP_LOWLEVEL_INIT
> +
> /* SD/MMC configuration */
> #define CONFIG_GENERIC_MMC
> #define CONFIG_MMC
> @@ -148,7 +150,10 @@
> #define CONFIG_ENV_OFFSET (RESERVE_BLOCK_SIZE + BL1_SIZE)
> #define CONFIG_DOS_PARTITION 1
>
> -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
> +#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024)
> +
> +#define CONFIG_SYS_INIT_SP_ADDR 0x02040000
>
> /* U-boot copy size from boot Media to DRAM.*/
> #define COPY_BL2_SIZE 0x80000
> @@ -157,4 +162,5 @@
>
> /* Enable devicetree support */
> #define CONFIG_OF_LIBFDT
> +
> #endif /* __CONFIG_H */
> diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h
> index db78127..38ba292 100644
> --- a/include/configs/smdkv310.h
> +++ b/include/configs/smdkv310.h
> @@ -58,6 +58,7 @@
> /* Handling Sleep Mode*/
> #define S5P_CHECK_SLEEP 0x00000BAD
> #define S5P_CHECK_DIDLE 0xBAD00000
> +#define S5P_CHECK_LPA 0xABAD0000
>
> /* Size of malloc() pool */
> #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (1 << 20))
> @@ -94,6 +95,7 @@
>
> /* MMC SPL */
> #define CONFIG_SPL
> +#define CONFIG_SKIP_LOWLEVEL_INIT
> #define COPY_BL2_FNPTR_ADDR 0x00002488
>
> #define CONFIG_SPL_TEXT_BASE 0x02021410
> @@ -147,7 +149,10 @@
> #define CONFIG_ENV_OFFSET (RESERVE_BLOCK_SIZE + BL1_SIZE)
> #define CONFIG_DOS_PARTITION 1
>
> -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
> +#define CONFIG_SPL_MAX_FOOTPRINT (14 * 1024)
> +
> +#define CONFIG_SYS_INIT_SP_ADDR 0x02040000
>
> /* U-boot copy size from boot Media to DRAM.*/
> #define COPY_BL2_SIZE 0x80000
>
Thanks,
Minkyu Kang.
More information about the U-Boot
mailing list