[U-Boot] [PATCH 2/3] usb: omap5-evm: Add ethernet support to the uevm
Lokesh Vutla
lokeshvutla at ti.com
Tue Jul 9 05:29:18 CEST 2013
Hi Dan,
On Tuesday 09 July 2013 02:29 AM, Dan Murphy wrote:
> Add code to configure the USB EHCI host controller.
> This enumerates an ethernet controller through USB3 using
> the HSIC lines.
>
> Signed-off-by: Dan Murphy <dmurphy at ti.com>
> ---
> arch/arm/cpu/armv7/omap5/hw_data.c | 15 +++++++++++
> arch/arm/include/asm/arch-omap5/clock.h | 6 +++++
> arch/arm/include/asm/arch-omap5/ehci.h | 44 +++++++++++++++++++++++++++++++
> arch/arm/include/asm/ehci-omap.h | 1 +
> board/ti/omap5_uevm/evm.c | 35 ++++++++++++++++++++++++
> board/ti/omap5_uevm/mux_data.h | 4 ++-
> drivers/usb/host/ehci-omap.c | 2 +-
> include/configs/omap5_common.h | 2 --
> include/configs/omap5_uevm.h | 23 ++++++++++++++++
> 9 files changed, 128 insertions(+), 4 deletions(-)
> create mode 100644 arch/arm/include/asm/arch-omap5/ehci.h
I see a other patch from you which adds the same file.
Is the previous patch sent by mistake?
>
> diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c
> index 56cf1f8..f3973ee 100644
> --- a/arch/arm/cpu/armv7/omap5/hw_data.c
> +++ b/arch/arm/cpu/armv7/omap5/hw_data.c
> @@ -412,6 +412,8 @@ void enable_basic_clocks(void)
> (*prcm)->cm_l4per_gpio4_clkctrl,
> (*prcm)->cm_l4per_gpio5_clkctrl,
> (*prcm)->cm_l4per_gpio6_clkctrl,
> + (*prcm)->cm_clksel_usb_60mhz,
> + (*prcm)->cm_l3init_hsusbtll_clkctrl,
> 0
> };
>
> @@ -423,6 +425,7 @@ void enable_basic_clocks(void)
> (*prcm)->cm_wkup_wdtimer2_clkctrl,
> (*prcm)->cm_l4per_uart3_clkctrl,
> (*prcm)->cm_l4per_i2c1_clkctrl,
> + (*prcm)->cm_l3init_hsusbhost_clkctrl,
> 0
> };
>
> @@ -446,6 +449,14 @@ void enable_basic_clocks(void)
> setbits_le32((*prcm)->cm_wkup_gptimer1_clkctrl,
> GPTIMER1_CLKCTRL_CLKSEL_MASK);
>
> + /* Enbale all 3 usb ports enable uhh, utmi and hsic clocks*/
> + setbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl,
> + USB_HOST_HS_CLKCTRL_MASK);
> +
> + /* Enbale all 3 usb host ports tll clocks*/
> + setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl,
> + USB_TLL_HS_CLKCTRL_MASK);
Please keep this under a macro.
> +
> do_enable_clocks(clk_domains_essential,
> clk_modules_hw_auto_essential,
> clk_modules_explicit_en_essential,
> @@ -480,6 +491,10 @@ void enable_basic_uboot_clocks(void)
> 0
> };
>
> + /* Enbale all 3 usb host ports tll clocks*/
> + setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl,
> + USB_TLL_HS_CLKCTRL_MASK);
> +
> do_enable_clocks(clk_domains_essential,
> clk_modules_hw_auto_essential,
> clk_modules_explicit_en_essential,
> diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h
> index 4d2765d..f98fe74 100644
> --- a/arch/arm/include/asm/arch-omap5/clock.h
> +++ b/arch/arm/include/asm/arch-omap5/clock.h
> @@ -165,6 +165,12 @@
> /* CM_L3INIT_USBPHY_CLKCTRL */
> #define USBPHY_CLKCTRL_OPTFCLKEN_PHY_48M_MASK 8
>
> +/* CM_L3INIT_USB_HOST_HS_CLKCTRL */
> +#define USB_HOST_HS_CLKCTRL_MASK 0x7FC0
> +
> +/* CM_L3INIT_USB_TLL_HS_CLKCTRL */
> +#define USB_TLL_HS_CLKCTRL_MASK 0x700
> +
> /* CM_MPU_MPU_CLKCTRL */
> #define MPU_CLKCTRL_CLKSEL_EMIF_DIV_MODE_SHIFT 24
> #define MPU_CLKCTRL_CLKSEL_EMIF_DIV_MODE_MASK (3 << 24)
> diff --git a/arch/arm/include/asm/arch-omap5/ehci.h b/arch/arm/include/asm/arch-omap5/ehci.h
> new file mode 100644
> index 0000000..49197f2
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-omap5/ehci.h
> @@ -0,0 +1,44 @@
> +/*
> + * OMAP EHCI port support
> + * Based on LINUX KERNEL
> + * drivers/usb/host/ehci-omap.c and drivers/mfd/omap-usb-host.c
> + *
> + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com*
2013...:)
Thanks
Lokesh
> + * Author: Govindraj R <govindraj.raja at ti.com>
> + *
> + * This program is free software: you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 of
> + * the License as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#ifndef _EHCI_H
> +#define _EHCI_H
> +
> +#define OMAP_EHCI_BASE (OMAP54XX_L4_CORE_BASE + 0x64C00)
> +#define OMAP_UHH_BASE (OMAP54XX_L4_CORE_BASE + 0x64000)
> +#define OMAP_USBTLL_BASE (OMAP54XX_L4_CORE_BASE + 0x62000)
> +
> +/* TLL Register Set */
> +#define OMAP_USBTLL_SYSCONFIG_SIDLEMODE (1 << 3)
> +#define OMAP_USBTLL_SYSCONFIG_ENAWAKEUP (1 << 2)
> +#define OMAP_USBTLL_SYSCONFIG_SOFTRESET (1 << 1)
> +#define OMAP_USBTLL_SYSCONFIG_CACTIVITY (1 << 8)
> +#define OMAP_USBTLL_SYSSTATUS_RESETDONE 1
> +
> +#define OMAP_UHH_SYSCONFIG_SOFTRESET 1
> +#define OMAP_UHH_SYSSTATUS_EHCI_RESETDONE (1 << 2)
> +#define OMAP_UHH_SYSCONFIG_NOIDLE (1 << 2)
> +#define OMAP_UHH_SYSCONFIG_NOSTDBY (1 << 4)
> +
> +#define OMAP_UHH_SYSCONFIG_VAL (OMAP_UHH_SYSCONFIG_NOIDLE | \
> + OMAP_UHH_SYSCONFIG_NOSTDBY)
> +
> +#endif /* _EHCI_H */
> diff --git a/arch/arm/include/asm/ehci-omap.h b/arch/arm/include/asm/ehci-omap.h
> index 77e8170..0b09e9d 100644
> --- a/arch/arm/include/asm/ehci-omap.h
> +++ b/arch/arm/include/asm/ehci-omap.h
> @@ -42,6 +42,7 @@ enum usbhs_omap_port_mode {
> /* Values of UHH_REVISION - Note: these are not given in the TRM */
> #define OMAP_USBHS_REV1 0x00000010 /* OMAP3 */
> #define OMAP_USBHS_REV2 0x50700100 /* OMAP4 */
> +#define OMAP_USBHS_REV2_1 0x50700101 /* OMAP5 */
>
> /* UHH Register Set */
> #define OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN (1 << 2)
> diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c
> index 00bd72d..21d4704 100644
> --- a/board/ti/omap5_uevm/evm.c
> +++ b/board/ti/omap5_uevm/evm.c
> @@ -29,6 +29,12 @@
>
> #include "mux_data.h"
>
> +#ifdef CONFIG_USB_EHCI
> +#include <usb.h>
> +#include <asm/arch/ehci.h>
> +#include <asm/ehci-omap.h>
> +#endif
> +
> DECLARE_GLOBAL_DATA_PTR;
>
> const struct omap_sysinfo sysinfo = {
> @@ -103,3 +109,32 @@ int board_mmc_init(bd_t *bis)
> return 0;
> }
> #endif
> +
> +#ifdef CONFIG_USB_EHCI
> +static struct omap_usbhs_board_data usbhs_bdata = {
> + .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
> + .port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC,
> + .port_mode[2] = OMAP_EHCI_PORT_MODE_HSIC,
> +};
> +
> +int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
> +{
> + int ret;
> +
> + ret = omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor);
> + if (ret < 0) {
> + printf("Failed to initialize ehci\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +int ehci_hcd_stop(void)
> +{
> + int ret;
> +
> + ret = omap_ehci_hcd_stop();
> + return ret;
> +}
> +#endif
> diff --git a/board/ti/omap5_uevm/mux_data.h b/board/ti/omap5_uevm/mux_data.h
> index a82795d..dc3a8b1 100644
> --- a/board/ti/omap5_uevm/mux_data.h
> +++ b/board/ti/omap5_uevm/mux_data.h
> @@ -56,7 +56,9 @@ const struct pad_conf_entry core_padconf_array_essential[] = {
> {USBD0_HS_DP, (IEN | M0)}, /* USBD0_HS_DP */
> {USBD0_HS_DM, (IEN | M0)}, /* USBD0_HS_DM */
> {USBD0_SS_RX, (IEN | M0)}, /* USBD0_SS_RX */
> -
> + {HSI2_ACWAKE, (M6)}, /* HSI2_ACWAKE */
> + {HSI2_CAFLAG, (M6)}, /* HSI2_CAFLAG */
> + {FREF_CLK1_OUT, (M0)}, /* FREF_CLK1_OUT */
> };
>
> const struct pad_conf_entry wkup_padconf_array_essential[] = {
> diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
> index 086c697..17f2214 100644
> --- a/drivers/usb/host/ehci-omap.c
> +++ b/drivers/usb/host/ehci-omap.c
> @@ -208,7 +208,7 @@ int omap_ehci_hcd_init(struct omap_usbhs_board_data *usbhs_pdata,
> clrbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS);
> else
> setbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS);
> - } else if (rev == OMAP_USBHS_REV2) {
> + } else if ((rev == OMAP_USBHS_REV2) || (rev == OMAP_USBHS_REV2_1)) {
> clrsetbits_le32(®, (OMAP_P1_MODE_CLEAR | OMAP_P2_MODE_CLEAR),
> OMAP4_UHH_HOSTCONFIG_APP_START_CLK);
>
> diff --git a/include/configs/omap5_common.h b/include/configs/omap5_common.h
> index b87ee42..32f053d 100644
> --- a/include/configs/omap5_common.h
> +++ b/include/configs/omap5_common.h
> @@ -113,8 +113,6 @@
> #define CONFIG_CMD_MMC /* MMC support */
>
> /* Disabled commands */
> -#undef CONFIG_CMD_NET
> -#undef CONFIG_CMD_NFS
> #undef CONFIG_CMD_FPGA /* FPGA configuration Support */
> #undef CONFIG_CMD_IMLS /* List all found images */
>
> diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h
> index 46dacc2..86f4238 100644
> --- a/include/configs/omap5_uevm.h
> +++ b/include/configs/omap5_uevm.h
> @@ -53,6 +53,29 @@
> #define CONFIG_PARTITION_UUIDS
> #define CONFIG_CMD_PART
>
> +/* USB UHH support options */
> +#define CONFIG_CMD_USB
> +#define CONFIG_USB_HOST
> +#define CONFIG_USB_EHCI
> +#define CONFIG_USB_EHCI_OMAP
> +#define CONFIG_USB_STORAGE
> +#define CONFIG_USB_ULPI
> +#define CONFIG_USB_ULPI_VIEWPORT_OMAP
> +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
> +
> +#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 79
> +#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 80
> +
> +/* Enabled commands */
> +#define CONFIG_NET_MULTI
> +#define CONFIG_CMD_DHCP /* DHCP Support */
> +#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
> +#define CONFIG_CMD_NFS /* NFS support */
> +
> +/* USB Networking options */
> +#define CONFIG_USB_HOST_ETHER
> +#define CONFIG_USB_ETHER_SMSC95XX
> +
> #define CONFIG_SYS_PROMPT "OMAP5432 uEVM # "
>
> #define CONSOLEDEV "ttyO2"
>
More information about the U-Boot
mailing list