[U-Boot] [PATCH 3/7 v7] powerpc: p1022ds: Enable P1022DS to boot from SD Card with SPL
ying.zhang at freescale.com
ying.zhang at freescale.com
Tue Jul 9 11:50:46 CEST 2013
From: Ying Zhang <b40530 at freescale.com>
Enable p1022ds to start from eSDHC with SPL.
Signed-off-by: Ying Zhang <b40530 at freescale.com>
---
Change from v6:
- Split from the patch "powerpc/p1022ds: boot from SD Card with SPL",
- this patch only enables p1022ds to boot from SD Card with SPL.
Change from v5:
- No change.
Change from v4:
- No change.
Change from v3:
- No change.
Change from v2:
- No change.
Change from v1:
- No change.
README | 4 ++
board/freescale/common/Makefile | 2 -
board/freescale/p1022ds/Makefile | 3 +
board/freescale/p1022ds/spl.c | 111 ++++++++++++++++++++++++++++++++++++++
board/freescale/p1022ds/tlb.c | 9 +++-
include/configs/P1022DS.h | 54 ++++++++++++++++---
6 files changed, 173 insertions(+), 10 deletions(-)
create mode 100644 board/freescale/p1022ds/spl.c
diff --git a/README b/README
index 9543749..5872b5e 100644
--- a/README
+++ b/README
@@ -3027,6 +3027,10 @@ FIT uImage format:
Set for the SPL on PPC mpc8xxx targets, support for
arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
+ CONFIG_SPL_COMMON_INIT_DDR
+ Set for common ddr init with serial presence detect in
+ SPL binary.
+
CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 37236d0..e991def 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -61,9 +61,7 @@ COBJS-$(CONFIG_MPC8555CDS) += cds_pci_ft.o
COBJS-$(CONFIG_MPC8536DS) += ics307_clk.o
COBJS-$(CONFIG_MPC8572DS) += ics307_clk.o
-ifndef CONFIG_SPL_BUILD
COBJS-$(CONFIG_P1022DS) += ics307_clk.o
-endif
COBJS-$(CONFIG_P2020DS) += ics307_clk.o
COBJS-$(CONFIG_P3041DS) += ics307_clk.o
COBJS-$(CONFIG_P4080DS) += ics307_clk.o
diff --git a/board/freescale/p1022ds/Makefile b/board/freescale/p1022ds/Makefile
index 0eeef05..9746063 100644
--- a/board/freescale/p1022ds/Makefile
+++ b/board/freescale/p1022ds/Makefile
@@ -24,6 +24,9 @@ ifdef MINIMAL
COBJS-y += spl_minimal.o tlb.o law.o
else
+ifdef CONFIG_SPL_BUILD
+COBJS-y += spl.o
+endif
COBJS-y += $(BOARD).o
COBJS-y += ddr.o
COBJS-y += law.o
diff --git a/board/freescale/p1022ds/spl.c b/board/freescale/p1022ds/spl.c
new file mode 100644
index 0000000..9927671
--- /dev/null
+++ b/board/freescale/p1022ds/spl.c
@@ -0,0 +1,111 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ *
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <nand.h>
+#include <i2c.h>
+#include "../common/ngpixis.h"
+#include <fsl_esdhc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static const u32 sysclk_tbl[] = {
+ 66666000, 7499900, 83332500, 8999900,
+ 99999000, 11111000, 12499800, 13333200
+};
+
+ulong get_effective_memsize(void)
+{
+ return CONFIG_SYS_L2_SIZE;
+}
+
+void board_init_f(ulong bootflag)
+{
+ int px_spd;
+ u32 plat_ratio, sys_clk, bus_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ console_init_f();
+
+ /* Set pmuxcr to allow both i2c1 and i2c2 */
+ setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000);
+ setbits_be32(&gur->pmuxcr,
+ in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA);
+
+ /* Read back the register to synchronize the write. */
+ in_be32(&gur->pmuxcr);
+
+ /* initialize selected port with appropriate baud rate */
+ px_spd = in_8((unsigned char *)(PIXIS_BASE + PIXIS_SPD));
+ sys_clk = sysclk_tbl[px_spd & PIXIS_SPD_SYSCLK_MASK];
+ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+ bus_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ bus_clk / 16 / CONFIG_BAUDRATE);
+#ifdef CONFIG_SPL_MMC_BOOT
+ puts("\nSD boot...\n");
+#endif
+
+ /* copy code to RAM and jump to it - this should not return */
+ /* NOTE - code has to be copied out of NAND buffer before
+ * other blocks can be read.
+ */
+ relocate_code(CONFIG_SPL_RELOC_STACK, 0,
+ CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ /* Pointer is writable since we allocated a register for it */
+ gd = (gd_t *)CONFIG_SPL_GD_ADDR;
+ bd_t *bd;
+
+ memset(gd, 0, sizeof(gd_t));
+ bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L2_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, \
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+ env_init();
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+#endif
+ /* relocate environment function pointers etc. */
+ env_relocate();
+
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ gd->ram_size = initdram(0);
+ puts("Second program loader running in sram...\n");
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#endif
+}
diff --git a/board/freescale/p1022ds/tlb.c b/board/freescale/p1022ds/tlb.c
index 3acc449..9b14c37 100644
--- a/board/freescale/p1022ds/tlb.c
+++ b/board/freescale/p1022ds/tlb.c
@@ -74,7 +74,8 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 7, BOOKE_PAGESZ_4K, 1),
-#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL)
+#if defined(CONFIG_SYS_RAMBOOT) || \
+ (defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR))
/* **** - eSDHC/eSPI/NAND boot */
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
@@ -93,6 +94,12 @@ struct fsl_e_tlb_entry tlb_table[] = {
0, 10, BOOKE_PAGESZ_16K, 1),
#endif
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+ /* *I*G - L2SRAM */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+ 0, 11, BOOKE_PAGESZ_256K, 1)
+#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h
index bcbda30..7cb049c 100644
--- a/include/configs/P1022DS.h
+++ b/include/configs/P1022DS.h
@@ -19,11 +19,32 @@
#endif
#ifdef CONFIG_SDCARD
-#define CONFIG_RAMBOOT_SDCARD
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE 0x11000000
-#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE 0x11001000
+#define CONFIG_SPL_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_PAD_TO 0x18000
+#define CONFIG_SPL_MAX_SIZE (96 * 1024)
+#define CONFIG_SYS_MMC_U_BOOT_SIZE (512 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000)
+#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (96 << 10)
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#define CONFIG_SPL_MMC_BOOT
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_COMMON_INIT_DDR
+#endif
#endif
#ifdef CONFIG_SPIFLASH
@@ -294,6 +315,24 @@
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
/*
+ * Config the L2 Cache as L2 SRAM
+*/
+#if defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_SDCARD)
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_L2_SIZE (256 << 10)
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 128 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10)
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 160 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (96 << 10)
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024)
+#endif
+#endif
+
+/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
@@ -301,7 +340,7 @@
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#ifdef CONFIG_SPL_BUILD
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif
@@ -532,8 +571,9 @@
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
#define CONFIG_ENV_SECT_SIZE 0x10000
-#elif defined(CONFIG_RAMBOOT_SDCARD)
+#elif defined(CONFIG_SDCARD)
#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_FSL_FIXED_MMC_LOCATION
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_MMC_ENV_DEV 0
#elif defined(CONFIG_NAND)
--
1.7.0.4
More information about the U-Boot
mailing list