[U-Boot] [PATCH 4/5] omap3_beagle: support findfdt and loadfdt for devicetree support

[Nishanth Menon]

On 17:02-20130711, Robert Nelson wrote:
> On Thu, Jul 11, 2013 at 4:52 PM, Nishanth Menon <nm at ti.com> wrote:
> > For folks not using concatenated device tree with uImage, having
> > an handy function to find and load device tree is very handy.
> >
> > So introduce findfdt and loadfdt and run findfdt by default to make
> > it easier on user scripts.
> >
> > Signed-off-by: Nishanth Menon <nm at ti.com>
> > ---
> >  include/configs/omap3_beagle.h |   17 +++++++++++++++++
> >  1 file changed, 17 insertions(+)
> >
> > diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> > index bdeee17..7833208 100644
> > --- a/include/configs/omap3_beagle.h
> > +++ b/include/configs/omap3_beagle.h
> > @@ -210,6 +210,8 @@
> >  #define CONFIG_EXTRA_ENV_SETTINGS \
> >         "loadaddr=0x80200000\0" \
> >         "rdaddr=0x81000000\0" \
> > +       "fdt_high=0xffffffff\0" \
> > +       "fdtaddr=0x80f80000\0" \
> >         "usbtty=cdc_acm\0" \
> >         "bootfile=uImage\0" \
> >         "ramdisk=ramdisk.gz\0" \
> > @@ -250,6 +252,19 @@
> >                 "omapdss.def_disp=${defaultdisplay} " \
> >                 "root=${nandroot} " \
> >                 "rootfstype=${nandrootfstype}\0" \
> > +       "findfdt=" \
> > +               "if test $beaglerev = AxBx; then " \
> > +                       "setenv fdtfile omap3-beagle.dtb; fi; " \
> > +               "if test $beaglerev = Cx; then " \
> > +                       "setenv fdtfile omap3-beagle.dtb; fi; " \
> > +               "if test $beaglerev = xMA; then " \
> > +                       "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
> > +               "if test $beaglerev = xMB; then " \
> > +                       "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
> 
> There is no need for the "xMB" variant, as the gpio pins used for
> identification where never changed from the xMA when the newer silcon
> was used for the xMB (i guess if we look at the omap's es revision, we
> could figure out which are xMB's, but right now that isn't done in
> u-boot....)
I suppose then the following is ok to do as well?
diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
index c686f40..6094b0f 100644
--- a/board/ti/beagle/beagle.c
+++ b/board/ti/beagle/beagle.c
@@ -369,16 +369,6 @@ int misc_init_r(void)
 					TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
 					TWL4030_PM_RECEIVER_DEV_GRP_P1);
 		break;
-	case REVISION_XM_B:
-		printf("Beagle xM Rev B\n");
-		setenv("beaglerev", "xMB");
-		MUX_BEAGLE_XM();
-		/* Set VAUX2 to 1.8V for EHCI PHY */
-		twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
-					TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
-					TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
-					TWL4030_PM_RECEIVER_DEV_GRP_P1);
-		break;
 	case REVISION_XM_C:
 		printf("Beagle xM Rev C\n");
 		setenv("beaglerev", "xMC");

-- 
Regards,
Nishanth Menon