[U-Boot] [PATCH 03/11] video: Add System-Mode configuration hook into mxsfb

Marek Vasut marex at denx.de
Wed Jul 31 01:31:48 CEST 2013


Dear Otavio Salvador,

> On Tue, Jul 30, 2013 at 7:45 PM, Marek Vasut <marex at denx.de> wrote:
> > Dear Otavio Salvador,
> > 
> >> On Tue, Jul 30, 2013 at 6:37 PM, Marek Vasut <marex at denx.de> wrote:
> >> > Add hook that allow configuring SmartLCD attached the MXS LCDIF
> >> > controller operating in System-Mode. This hook can be overriden
> >> > by a platform-specific SmartLCD programming routine, which writes
> >> > the SmartLCD specific values into it's registers.
> >> > 
> >> > Also, this patch makes sure the SYNC signals are off for the
> >> > SmartLCD case.
> >> > 
> >> > Signed-off-by: Marek Vasut <marex at denx.de>
> >> > Cc: Anatolij Gustschin <agust at denx.de>
> >> > Cc: Fabio Estevam <fabio.estevam at freescale.com>
> >> > Cc: Otavio Salvador <otavio at ossystems.com.br>
> >> > Cc: Stefano Babic <sbabic at denx.de>
> >> > ---
> >> > 
> >> >  drivers/video/mxsfb.c |   16 ++++++++++++++++
> >> >  1 file changed, 16 insertions(+)
> >> > 
> >> > diff --git a/drivers/video/mxsfb.c b/drivers/video/mxsfb.c
> >> > index dbc63a6..78709dd 100644
> >> > --- a/drivers/video/mxsfb.c
> >> > +++ b/drivers/video/mxsfb.c
> >> > @@ -34,6 +34,17 @@
> >> > 
> >> >  static GraphicDevice panel;
> >> > 
> >> > +/**
> >> > + * mxsfb_system_setup() - Fine-tune LCDIF configuration
> >> > + *
> >> > + * This function is used to adjust the LCDIF configuration. This is
> >> > usually + * needed when driving the controller in System-Mode to
> >> > operate an 8080 or + * 6800 connected SmartLCD.
> >> > + */
> >> > +__weak void mxsfb_system_setup(void)
> >> > +{
> >> > +}
> >> > +
> >> > 
> >> >  /*
> >> >  
> >> >   * DENX M28EVK:
> >> >   * setenv videomode
> >> > 
> >> > @@ -88,6 +99,9 @@ static void mxs_lcd_init(GraphicDevice *panel,
> >> > 
> >> >         writel(valid_data << LCDIF_CTRL1_BYTE_PACKING_FORMAT_OFFSET,
> >> >         
> >> >                 &regs->hw_lcdif_ctrl1);
> >> > 
> >> > +
> >> > +       mxsfb_system_setup();
> >> > +
> >> > 
> >> >         writel((mode->yres << LCDIF_TRANSFER_COUNT_V_COUNT_OFFSET) |
> >> >         mode->xres,
> >> >         
> >> >                 &regs->hw_lcdif_transfer_count);
> >> > 
> >> > @@ -115,8 +129,10 @@ static void mxs_lcd_init(GraphicDevice *panel,
> >> > 
> >> >         /* Flush FIFO first */
> >> >         writel(LCDIF_CTRL1_FIFO_CLEAR, &regs->hw_lcdif_ctrl1_set);
> >> > 
> >> > +#ifndef CONFIG_VIDEO_MXS_MODE_SYSTEM
> >> 
> >> Mode system or System mode?
> > 
> > This is a name of configuration macro, CONFIG_VIDEO_MXS_MODE_SYSTEM .
> > Otherwise I do not understand what you are asking about.
> 
> I got this but accordingly to your commitlog it should be
> CONFIG_VIDEO_MXS_SYSTEM_MODE to match the description. Any reason to
> not use this name?

Sorry, is this name of the macro mentioned in the commit log anywhere? I don't 
see it there. I believe grepping for CONFIG_VIDEO_MXS_MODE will make it easier 
in the future --  if we were to support more modes -- to find all occurances of 
such conditionals.

Best regards,
Marek Vasut


More information about the U-Boot mailing list