[U-Boot] [PATCH 11/21] T4/usb: move usb 2.0 utmi dual phy init code to cpu_init.c

[York Sun]

From: Roy Zang <tie-fei.zang at freescale.com>

This is what we have done for the UTMI PHY on P3041/P5020. Then the PHY
initialization can be reused in kernel without  “usb start” command.

Signed-off-by: Roy Zang <tie-fei.zang at freescale.com>
---
 arch/powerpc/cpu/mpc85xx/cpu_init.c |   22 ++++++++++++++++++++++
 drivers/usb/host/ehci-fsl.c         |   21 ---------------------
 2 files changed, 22 insertions(+), 21 deletions(-)

diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c
index de9d916..8b12dd2 100644
--- a/arch/powerpc/cpu/mpc85xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c
@@ -623,6 +623,28 @@ skip_l2:
 	}
 #endif
 
+#if defined(CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE)
+		ccsr_usb_phy_t *usb_phy =
+			(void *)CONFIG_SYS_MPC85xx_USB1_PHY_ADDR;
+		setbits_be32(&usb_phy->pllprg[1],
+				CONFIG_SYS_FSL_USB_PLLPRG2_PHY2_CLK_EN |
+				CONFIG_SYS_FSL_USB_PLLPRG2_PHY1_CLK_EN |
+				CONFIG_SYS_FSL_USB_PLLPRG2_MFI |
+				CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN);
+		setbits_be32(&usb_phy->port1.ctrl,
+				CONFIG_SYS_FSL_USB_CTRL_PHY_EN);
+		setbits_be32(&usb_phy->port1.drvvbuscfg,
+				CONFIG_SYS_FSL_USB_DRVVBUS_CR_EN);
+		setbits_be32(&usb_phy->port1.pwrfltcfg,
+				CONFIG_SYS_FSL_USB_PWRFLT_CR_EN);
+		setbits_be32(&usb_phy->port2.ctrl,
+				CONFIG_SYS_FSL_USB_CTRL_PHY_EN);
+		setbits_be32(&usb_phy->port2.drvvbuscfg,
+				CONFIG_SYS_FSL_USB_DRVVBUS_CR_EN);
+		setbits_be32(&usb_phy->port2.pwrfltcfg,
+				CONFIG_SYS_FSL_USB_PWRFLT_CR_EN);
+#endif
+
 #ifdef CONFIG_FMAN_ENET
 	fman_enet_init();
 #endif
diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index 81a70c0..f54b408 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -89,27 +89,6 @@ int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
 
 	if (!strcmp(phy_type, "utmi")) {
 #if defined(CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY)
-#if defined(CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE)
-		ccsr_usb_phy_t *usb_phy =
-			(void *)CONFIG_SYS_MPC85xx_USB1_PHY_ADDR;
-		setbits_be32(&usb_phy->pllprg[1],
-				CONFIG_SYS_FSL_USB_PLLPRG2_PHY2_CLK_EN |
-				CONFIG_SYS_FSL_USB_PLLPRG2_PHY1_CLK_EN |
-				CONFIG_SYS_FSL_USB_PLLPRG2_MFI |
-				CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN);
-		setbits_be32(&usb_phy->port1.ctrl,
-				CONFIG_SYS_FSL_USB_CTRL_PHY_EN);
-		setbits_be32(&usb_phy->port1.drvvbuscfg,
-				CONFIG_SYS_FSL_USB_DRVVBUS_CR_EN);
-		setbits_be32(&usb_phy->port1.pwrfltcfg,
-				CONFIG_SYS_FSL_USB_PWRFLT_CR_EN);
-		setbits_be32(&usb_phy->port2.ctrl,
-				CONFIG_SYS_FSL_USB_CTRL_PHY_EN);
-		setbits_be32(&usb_phy->port2.drvvbuscfg,
-				CONFIG_SYS_FSL_USB_DRVVBUS_CR_EN);
-		setbits_be32(&usb_phy->port2.pwrfltcfg,
-				CONFIG_SYS_FSL_USB_PWRFLT_CR_EN);
-#endif
 		setbits_be32(&ehci->control, PHY_CLK_SEL_UTMI);
 		setbits_be32(&ehci->control, UTMI_PHY_EN);
 		udelay(1000); /* delay required for PHY Clk to appear */
-- 
1.7.9.5