[U-Boot] [PATCH 16/21] T4240/eth: fix SGMII card PHY address

[York Sun]

From: Shaohui Xie <Shaohui.Xie at freescale.com>

QSGMII card assumed to be used by default, but if SGMII card is used,
it will use different PHY address, but we don't know which card is used
until we access PHY on the card. So we check the card type slot by slot,
if we can read a PHY ID by reading a SGMII PHY address on a slot, then
the slot must have a SGMII card pluged, we mark all ports on that slot,
and fix dts to use the SGMII card PHY address when doing dts fixup
for the marked ports.

Signed-off-by: Shaohui Xie <Shaohui.Xie at freescale.com>
---
 board/freescale/t4qds/eth.c |  137 +++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 133 insertions(+), 4 deletions(-)

diff --git a/board/freescale/t4qds/eth.c b/board/freescale/t4qds/eth.c
index 2232eea..ec0afce 100644
--- a/board/freescale/t4qds/eth.c
+++ b/board/freescale/t4qds/eth.c
@@ -78,6 +78,7 @@ static u8 slot_qsgmii_phyaddr[5][4] = {
 	{8, 9, 0xa, 0xb},
 	{0xc, 0xd, 0xe, 0xf},
 };
+static u8 qsgmiiphy_fix[NUM_FM_PORTS] = {0};
 
 static const char *t4240qds_mdio_name_for_muxval(u8 muxval)
 {
@@ -189,17 +190,87 @@ void board_ft_fman_fixup_port(void *blob, char * prop, phys_addr_t pa,
 {
 	if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
 		switch (port) {
+		case FM1_DTSEC1:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy21");
+			break;
+		case FM1_DTSEC2:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy22");
+			break;
+		case FM1_DTSEC3:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy23");
+			break;
+		case FM1_DTSEC4:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy24");
+			break;
+		case FM1_DTSEC6:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy12");
+			break;
 		case FM1_DTSEC9:
-			fdt_set_phy_handle(blob, prop, pa, "phy_sgmii4");
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy14");
+			else
+				fdt_set_phy_handle(blob, prop, pa,
+						"phy_sgmii4");
 			break;
 		case FM1_DTSEC10:
-			fdt_set_phy_handle(blob, prop, pa, "phy_sgmii3");
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy13");
+			else
+				fdt_set_phy_handle(blob, prop, pa,
+						"phy_sgmii3");
+			break;
+		case FM2_DTSEC1:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy41");
+			break;
+		case FM2_DTSEC2:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy42");
+			break;
+		case FM2_DTSEC3:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy43");
+			break;
+		case FM2_DTSEC4:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy44");
+			break;
+		case FM2_DTSEC6:
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy32");
 			break;
 		case FM2_DTSEC9:
-			fdt_set_phy_handle(blob, prop, pa, "phy_sgmii12");
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy34");
+			else
+				fdt_set_phy_handle(blob, prop, pa,
+						"phy_sgmii12");
 			break;
 		case FM2_DTSEC10:
-			fdt_set_phy_handle(blob, prop, pa, "phy_sgmii11");
+			if (qsgmiiphy_fix[port])
+				fdt_set_phy_handle(blob, prop, pa,
+						"sgmii_phy33");
+			else
+				fdt_set_phy_handle(blob, prop, pa,
+						"phy_sgmii11");
 			break;
 		default:
 			break;
@@ -263,6 +334,62 @@ void fdt_fixup_board_enet(void *fdt)
 	}
 }
 
+static void initialize_qsgmiiphy_fix(void)
+{
+	int i;
+	unsigned short reg;
+
+	for (i = 1; i <= 4; i++) {
+		/*
+		 * Try to read if a SGMII card is used, we do it slot by slot.
+		 * if a SGMII PHY address is valid on a slot, then we mark
+		 * all ports on the slot, then fix the PHY address for the
+		 * marked port when doing dtb fixup.
+		 */
+		if (miiphy_read(mdio_names[i],
+			SGMII_CARD_PORT1_PHY_ADDR, MII_PHYSID2, &reg) != 0) {
+			debug("Slot%d PHY ID register 2 read failed\n", i);
+			continue;
+		}
+
+		debug("Slot%d MII_PHYSID2 @ 0x1c= 0x%04x\n", i, reg);
+
+		if (reg == 0xFFFF) {
+			/* No physical device present at this address */
+			continue;
+		}
+
+		switch (i) {
+		case 1:
+			qsgmiiphy_fix[FM1_DTSEC5] = 1;
+			qsgmiiphy_fix[FM1_DTSEC6] = 1;
+			qsgmiiphy_fix[FM1_DTSEC9] = 1;
+			qsgmiiphy_fix[FM1_DTSEC10] = 1;
+			break;
+		case 2:
+			qsgmiiphy_fix[FM1_DTSEC1] = 1;
+			qsgmiiphy_fix[FM1_DTSEC2] = 1;
+			qsgmiiphy_fix[FM1_DTSEC3] = 1;
+			qsgmiiphy_fix[FM1_DTSEC4] = 1;
+			break;
+		case 3:
+			qsgmiiphy_fix[FM2_DTSEC5] = 1;
+			qsgmiiphy_fix[FM2_DTSEC6] = 1;
+			qsgmiiphy_fix[FM2_DTSEC9] = 1;
+			qsgmiiphy_fix[FM2_DTSEC10] = 1;
+			break;
+		case 4:
+			qsgmiiphy_fix[FM2_DTSEC1] = 1;
+			qsgmiiphy_fix[FM2_DTSEC2] = 1;
+			qsgmiiphy_fix[FM2_DTSEC3] = 1;
+			qsgmiiphy_fix[FM2_DTSEC4] = 1;
+			break;
+		default:
+			break;
+		}
+	}
+}
+
 int board_eth_init(bd_t *bis)
 {
 #if defined(CONFIG_FMAN_ENET)
@@ -575,6 +702,8 @@ int board_eth_init(bd_t *bis)
 	}
 #endif /* CONFIG_SYS_NUM_FMAN */
 
+	initialize_qsgmiiphy_fix();
+
 	cpu_eth_init(bis);
 #endif /* CONFIG_FMAN_ENET */
 
-- 
1.7.9.5