[U-Boot] [PATCH V3 01/10] twl4030: make twl4030_i2c_write_u8 prototype consistent
Nishanth Menon
nm at ti.com
Tue Mar 26 16:20:49 CET 2013
u-boot standard i2c register write prototype is
i2c_reg_write(u8 addr, u8 reg, u8 val)
twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val)
Signed-off-by: Nishanth Menon <nm at ti.com>
---
V2: http://patchwork.ozlabs.org/patch/230267/
Changes since v2:
- checkpatch cleanup
board/cm_t35/cm_t35.c | 20 +++++++++----------
board/nokia/rx51/rx51.c | 36 +++++++++++++++++-----------------
board/pandora/pandora.c | 3 ++-
drivers/misc/twl4030_led.c | 4 ++--
drivers/power/twl4030.c | 12 ++++++------
drivers/usb/phy/twl4030.c | 46 ++++++++++++++++++++++----------------------
include/twl4030.h | 2 +-
7 files changed, 62 insertions(+), 61 deletions(-)
diff --git a/board/cm_t35/cm_t35.c b/board/cm_t35/cm_t35.c
index e0e8235..bccfacd 100644
--- a/board/cm_t35/cm_t35.c
+++ b/board/cm_t35/cm_t35.c
@@ -430,17 +430,17 @@ static void setup_net_chip_gmpc(void)
static void reset_net_chip(void)
{
/* Set GPIO1 of TPS65930 as output */
- twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
- TWL4030_BASEADD_GPIO + 0x03);
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x03,
+ 0x02);
/* Send a pulse on the GPIO pin */
- twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
- TWL4030_BASEADD_GPIO + 0x0C);
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C,
+ 0x02);
udelay(1);
- twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
- TWL4030_BASEADD_GPIO + 0x09);
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x09,
+ 0x02);
mdelay(40);
- twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
- TWL4030_BASEADD_GPIO + 0x0C);
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C,
+ 0x02);
mdelay(1);
}
#else
@@ -537,10 +537,10 @@ int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, offset);
/* Set GPIO6 and GPIO7 of TPS65930 as output */
val |= 0xC0;
- twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, val, offset);
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, val);
offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_SETGPIODATAOUT1;
/* Take both PHYs out of reset */
- twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0xC0, offset);
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, 0xC0);
udelay(1);
return omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor);
diff --git a/board/nokia/rx51/rx51.c b/board/nokia/rx51/rx51.c
index 48eb65f..860d52d 100644
--- a/board/nokia/rx51/rx51.c
+++ b/board/nokia/rx51/rx51.c
@@ -332,10 +332,10 @@ void *video_hw_init(void)
static void twl4030_regulator_set_mode(u8 id, u8 mode)
{
u16 msg = MSG_SINGULAR(DEV_GRP_P1, id, mode);
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, msg >> 8,
- TWL4030_PM_MASTER_PB_WORD_MSB);
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, msg & 0xff,
- TWL4030_PM_MASTER_PB_WORD_LSB);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+ TWL4030_PM_MASTER_PB_WORD_MSB, msg >> 8);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+ TWL4030_PM_MASTER_PB_WORD_LSB, msg & 0xff);
}
static void omap3_emu_romcode_call(u32 service_id, u32 *parameters)
@@ -410,8 +410,8 @@ int misc_init_r(void)
TWL4030_PM_MASTER_PB_CFG);
/* enable I2C access to powerbus (needed for twl4030 regulator) */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x02,
- TWL4030_PM_MASTER_PB_CFG);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG,
+ 0x02);
/* set VAUX3, VSIM and VMMC1 state to active - enable eMMC memory */
twl4030_regulator_set_mode(RES_VAUX3, RES_STATE_ACTIVE);
@@ -419,8 +419,8 @@ int misc_init_r(void)
twl4030_regulator_set_mode(RES_VMMC1, RES_STATE_ACTIVE);
/* restore I2C access state */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, state,
- TWL4030_PM_MASTER_PB_CFG);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG,
+ state);
/* set env variable attkernaddr for relocated kernel */
sprintf(buf, "%#x", KERNEL_ADDRESS);
@@ -481,8 +481,8 @@ void hw_watchdog_reset(void)
/* timeout 0 means watchdog is disabled */
/* reset watchdog timeout to 31s (maximum) */
if (timeout != 0)
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 31,
- TWL4030_PM_RECEIVER_WATCHDOG_CFG);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_WATCHDOG_CFG, 31);
/* store last watchdog reset time */
twl_wd_time = get_timer(0);
@@ -541,18 +541,18 @@ int rx51_kp_init(void)
ctrl |= TWL4030_KEYPAD_CTRL_KBD_ON;
ctrl |= TWL4030_KEYPAD_CTRL_SOFT_NRST;
ctrl |= TWL4030_KEYPAD_CTRL_SOFTMODEN;
- ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, ctrl,
- TWL4030_KEYPAD_KEYP_CTRL_REG);
+ ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD,
+ TWL4030_KEYPAD_KEYP_CTRL_REG, ctrl);
/* enable key event status */
- ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0xfe,
- TWL4030_KEYPAD_KEYP_IMR1);
+ ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD,
+ TWL4030_KEYPAD_KEYP_IMR1, 0xfe);
/* enable interrupt generation on rising and falling */
/* this is a workaround for qemu twl4030 emulation */
- ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0x57,
- TWL4030_KEYPAD_KEYP_EDR);
+ ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD,
+ TWL4030_KEYPAD_KEYP_EDR, 0x57);
/* enable ISR clear on read */
- ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0x05,
- TWL4030_KEYPAD_KEYP_SIH_CTRL);
+ ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD,
+ TWL4030_KEYPAD_KEYP_SIH_CTRL, 0x05);
return 0;
}
diff --git a/board/pandora/pandora.c b/board/pandora/pandora.c
index 9ff5dd7..5f0c58d 100644
--- a/board/pandora/pandora.c
+++ b/board/pandora/pandora.c
@@ -114,8 +114,9 @@ int misc_init_r(void)
/* Enable battery backup capacitor (3.2V, 0.5mA charge current) */
twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_BB_CFG,
TWL4030_BB_CFG_BBCHEN | TWL4030_BB_CFG_BBSEL_3200MV |
- TWL4030_BB_CFG_BBISEL_500UA, TWL4030_PM_RECEIVER_BB_CFG);
+ TWL4030_BB_CFG_BBISEL_500UA);
dieid_num_r();
diff --git a/drivers/misc/twl4030_led.c b/drivers/misc/twl4030_led.c
index 33cea11..e150d8f 100644
--- a/drivers/misc/twl4030_led.c
+++ b/drivers/misc/twl4030_led.c
@@ -42,7 +42,7 @@ void twl4030_led_init(unsigned char ledon_mask)
if (ledon_mask & TWL4030_LED_LEDEN_LEDBON)
ledon_mask |= TWL4030_LED_LEDEN_LEDBPWM;
- twl4030_i2c_write_u8(TWL4030_CHIP_LED, ledon_mask,
- TWL4030_LED_LEDEN);
+ twl4030_i2c_write_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN,
+ ledon_mask);
}
diff --git a/drivers/power/twl4030.c b/drivers/power/twl4030.c
index e7d5f13..2bf94b1 100644
--- a/drivers/power/twl4030.c
+++ b/drivers/power/twl4030.c
@@ -51,8 +51,8 @@ void twl4030_power_reset_init(void)
printf("Could not initialize hardware reset\n");
} else {
val |= TWL4030_PM_MASTER_SW_EVENTS_STOPON_PWRON;
- if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, val,
- TWL4030_PM_MASTER_P1_SW_EVENTS)) {
+ if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+ TWL4030_PM_MASTER_P1_SW_EVENTS, val)) {
printf("Error:TWL4030: failed to write the power register\n");
printf("Could not initialize hardware reset\n");
}
@@ -68,8 +68,8 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val,
int ret;
/* Select the Voltage */
- ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_val,
- vsel_reg);
+ ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_reg,
+ vsel_val);
if (ret != 0) {
printf("Could not write vsel to reg %02x (%d)\n",
vsel_reg, ret);
@@ -77,8 +77,8 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val,
}
/* Select the Device Group (enable the supply if dev_grp_sel != 0) */
- ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp_sel,
- dev_grp);
+ ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp,
+ dev_grp_sel);
if (ret != 0)
printf("Could not write grp_sel to reg %02x (%d)\n",
dev_grp, ret);
diff --git a/drivers/usb/phy/twl4030.c b/drivers/usb/phy/twl4030.c
index 54d2e61..f41cc07 100644
--- a/drivers/usb/phy/twl4030.c
+++ b/drivers/usb/phy/twl4030.c
@@ -54,7 +54,7 @@ static int twl4030_usb_write(u8 address, u8 data)
{
int ret;
- ret = twl4030_i2c_write_u8(TWL4030_CHIP_USB, data, address);
+ ret = twl4030_i2c_write_u8(TWL4030_CHIP_USB, address, data);
if (ret != 0)
printf("TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
@@ -78,40 +78,40 @@ static int twl4030_usb_read(u8 address)
static void twl4030_usb_ldo_init(void)
{
/* Enable writing to power configuration registers */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0xC0,
- TWL4030_PM_MASTER_PROTECT_KEY);
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x0C,
- TWL4030_PM_MASTER_PROTECT_KEY);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+ TWL4030_PM_MASTER_PROTECT_KEY, 0xC0);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+ TWL4030_PM_MASTER_PROTECT_KEY, 0x0C);
/* put VUSB3V1 LDO in active state */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00,
- TWL4030_PM_RECEIVER_VUSB_DEDICATED2);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_VUSB_DEDICATED2, 0x00);
/* input to VUSB3V1 LDO is from VBAT, not VBUS */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x14,
- TWL4030_PM_RECEIVER_VUSB_DEDICATED1);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_VUSB_DEDICATED1, 0x14);
/* turn on 3.1V regulator */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20,
- TWL4030_PM_RECEIVER_VUSB3V1_DEV_GRP);
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00,
- TWL4030_PM_RECEIVER_VUSB3V1_TYPE);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_VUSB3V1_DEV_GRP, 0x20);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_VUSB3V1_TYPE, 0x00);
/* turn on 1.5V regulator */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20,
- TWL4030_PM_RECEIVER_VUSB1V5_DEV_GRP);
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00,
- TWL4030_PM_RECEIVER_VUSB1V5_TYPE);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_VUSB1V5_DEV_GRP, 0x20);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_VUSB1V5_TYPE, 0x00);
/* turn on 1.8V regulator */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20,
- TWL4030_PM_RECEIVER_VUSB1V8_DEV_GRP);
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00,
- TWL4030_PM_RECEIVER_VUSB1V8_TYPE);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_VUSB1V8_DEV_GRP, 0x20);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER,
+ TWL4030_PM_RECEIVER_VUSB1V8_TYPE, 0x00);
/* disable access to power configuration registers */
- twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x00,
- TWL4030_PM_MASTER_PROTECT_KEY);
+ twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER,
+ TWL4030_PM_MASTER_PROTECT_KEY, 0x00);
}
static void twl4030_phy_power(void)
diff --git a/include/twl4030.h b/include/twl4030.h
index 5aa1841..aca695d 100644
--- a/include/twl4030.h
+++ b/include/twl4030.h
@@ -638,7 +638,7 @@
* examples are TWL4030_PM_RECEIVER_VMMC1_DEV_GRP and
* TWL4030_LED_LEDEN.
*/
-static inline int twl4030_i2c_write_u8(u8 chip_no, u8 val, u8 reg)
+static inline int twl4030_i2c_write_u8(u8 chip_no, u8 reg, u8 val)
{
return i2c_write(chip_no, reg, 1, &val, 1);
}
--
1.7.9.5
More information about the U-Boot
mailing list