[U-Boot] [PATCH v2] ARM: DRA: Enable VTT regulator

[Lokesh Vutla]

DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
---
Changes since v1:
	- Addressed comments from Tom.
 arch/arm/cpu/armv7/omap-common/hwinit-common.c |  3 +++
 board/ti/dra7xx/evm.c                          | 31 ++++++++++++++++++++++++++
 board/ti/dra7xx/mux_data.h                     |  1 +
 include/configs/dra7xx_evm.h                   |  1 +
 4 files changed, 36 insertions(+)

diff --git a/arch/arm/cpu/armv7/omap-common/hwinit-common.c b/arch/arm/cpu/armv7/omap-common/hwinit-common.c
index 5f50a19..750f33d 100644
--- a/arch/arm/cpu/armv7/omap-common/hwinit-common.c
+++ b/arch/arm/cpu/armv7/omap-common/hwinit-common.c
@@ -139,6 +139,9 @@ void s_init(void)
 #endif
 	prcm_init();
 #ifdef CONFIG_SPL_BUILD
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+	board_early_init_f();
+#endif
 	/* For regular u-boot sdram_init() is called from dram_init() */
 	sdram_init();
 #endif
diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c
index 7f19655..5a2cf36 100644
--- a/board/ti/dra7xx/evm.c
+++ b/board/ti/dra7xx/evm.c
@@ -13,6 +13,8 @@
 #include <common.h>
 #include <palmas.h>
 #include <sata.h>
+#include <asm/gpio.h>
+#include <asm/arch/gpio.h>
 #include <asm/arch/sys_proto.h>
 #include <asm/arch/mmc_host_def.h>
 #include <asm/arch/sata.h>
@@ -26,6 +28,9 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+/* GPIO 7_11 */
+#define GPIO_DDR_VTT_EN 203
+
 const struct omap_sysinfo sysinfo = {
 	"Board: DRA7xx\n"
 };
@@ -267,3 +272,29 @@ int board_eth_init(bd_t *bis)
 	return ret;
 }
 #endif
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+/* VTT regulator enable */
+static inline void vtt_regulator_enable(void)
+{
+	if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL)
+		return;
+
+	/* Do not enable VTT for DRA722 */
+	if (omap_revision() == DRA722_ES1_0)
+		return;
+
+	/*
+	 * EVM Rev G and later use gpio7_11 for DDR3 termination.
+	 * This is safe enough to do on older revs.
+	 */
+	gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
+	gpio_direction_output(GPIO_DDR_VTT_EN, 1);
+}
+
+int board_early_init_f(void)
+{
+	vtt_regulator_enable();
+	return 0;
+}
+#endif
diff --git a/board/ti/dra7xx/mux_data.h b/board/ti/dra7xx/mux_data.h
index c9e202a..bc17936 100644
--- a/board/ti/dra7xx/mux_data.h
+++ b/board/ti/dra7xx/mux_data.h
@@ -67,5 +67,6 @@ const struct pad_conf_entry core_padconf_array_essential[] = {
 	{GPMC_CS2, (IEN | PTU | PDIS | M1)},    /* QSPI1_CS0 */
 	{GPMC_CS3, (IEN | PTU | PDIS | M1)},    /* QSPI1_CS1*/
 	{USB2_DRVVBUS, (M0 | IEN | FSC) },
+	{SPI1_CS1, (PEN | IDIS | M14) },
 };
 #endif /* _MUX_DATA_DRA7XX_H_ */
diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h
index 8d0a0eb..38e2d44 100644
--- a/include/configs/dra7xx_evm.h
+++ b/include/configs/dra7xx_evm.h
@@ -13,6 +13,7 @@
 #define __CONFIG_DRA7XX_EVM_H
 
 #define CONFIG_DRA7XX
+#define CONFIG_BOARD_EARLY_INIT_F
 
 #ifndef CONFIG_QSPI_BOOT
 /* MMC ENV related defines */
-- 
1.9.1