[U-Boot] [PATCH 2/5] powerpc: mpc8xx: remove svm_sc8xx board
Masahiro Yamada
yamada.m at jp.panasonic.com
Wed Aug 6 05:59:52 CEST 2014
This board has been orphaned for a while and old enough.
Signed-off-by: Masahiro Yamada <yamada.m at jp.panasonic.com>
---
arch/powerpc/cpu/mpc8xx/Kconfig | 4 -
arch/powerpc/cpu/mpc8xx/cpu_init.c | 4 -
board/svm_sc8xx/Kconfig | 11 -
board/svm_sc8xx/MAINTAINERS | 6 -
board/svm_sc8xx/Makefile | 8 -
board/svm_sc8xx/flash.c | 666 -------------------------------------
board/svm_sc8xx/svm_sc8xx.c | 144 --------
board/svm_sc8xx/u-boot.lds | 99 ------
board/svm_sc8xx/u-boot.lds.debug | 114 -------
configs/svm_sc8xx_defconfig | 3 -
doc/README.scrapyard | 1 +
drivers/pcmcia/tqm8xx_pcmcia.c | 6 +-
include/commproc.h | 51 ---
include/configs/svm_sc8xx.h | 450 -------------------------
include/pcmcia.h | 2 +-
include/status_led.h | 14 -
16 files changed, 4 insertions(+), 1579 deletions(-)
delete mode 100644 board/svm_sc8xx/Kconfig
delete mode 100644 board/svm_sc8xx/MAINTAINERS
delete mode 100644 board/svm_sc8xx/Makefile
delete mode 100644 board/svm_sc8xx/flash.c
delete mode 100644 board/svm_sc8xx/svm_sc8xx.c
delete mode 100644 board/svm_sc8xx/u-boot.lds
delete mode 100644 board/svm_sc8xx/u-boot.lds.debug
delete mode 100644 configs/svm_sc8xx_defconfig
delete mode 100644 include/configs/svm_sc8xx.h
diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig
index ae97f30..6392c55 100644
--- a/arch/powerpc/cpu/mpc8xx/Kconfig
+++ b/arch/powerpc/cpu/mpc8xx/Kconfig
@@ -53,9 +53,6 @@ config TARGET_SXNI855T
config TARGET_SPD823TS
bool "Support SPD823TS"
-config TARGET_SVM_SC8XX
- bool "Support svm_sc8xx"
-
config TARGET_MHPC
bool "Support MHPC"
@@ -150,7 +147,6 @@ source "board/netvia/Kconfig"
source "board/r360mpi/Kconfig"
source "board/sixnet/Kconfig"
source "board/spd8xx/Kconfig"
-source "board/svm_sc8xx/Kconfig"
source "board/tqc/tqm8xx/Kconfig"
endmenu
diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c
index e51fec7..90c7e61 100644
--- a/arch/powerpc/cpu/mpc8xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c
@@ -44,11 +44,7 @@ void cpu_init_f (volatile immap_t * immr)
#endif /* CONFIG_WATCHDOG */
/* SIUMCR - contains debug pin configuration (11-6) */
-#ifndef CONFIG_SVM_SC8xx
immr->im_siu_conf.sc_siumcr |= CONFIG_SYS_SIUMCR;
-#else
- immr->im_siu_conf.sc_siumcr = CONFIG_SYS_SIUMCR;
-#endif
/* initialize timebase status and control register (11-26) */
/* unlock TBSCRK */
diff --git a/board/svm_sc8xx/Kconfig b/board/svm_sc8xx/Kconfig
deleted file mode 100644
index 522b1a8..0000000
--- a/board/svm_sc8xx/Kconfig
+++ /dev/null
@@ -1,11 +0,0 @@
-if TARGET_SVM_SC8XX
-
-config SYS_BOARD
- string
- default "svm_sc8xx"
-
-config SYS_CONFIG_NAME
- string
- default "svm_sc8xx"
-
-endif
diff --git a/board/svm_sc8xx/MAINTAINERS b/board/svm_sc8xx/MAINTAINERS
deleted file mode 100644
index c19bcae..0000000
--- a/board/svm_sc8xx/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-SVM_SC8XX BOARD
-M: John Zhan <zhanz at sinovee.com>
-S: Orphan (since 2014-06)
-F: board/svm_sc8xx/
-F: include/configs/svm_sc8xx.h
-F: configs/svm_sc8xx_defconfig
diff --git a/board/svm_sc8xx/Makefile b/board/svm_sc8xx/Makefile
deleted file mode 100644
index 4c0b4a3..0000000
--- a/board/svm_sc8xx/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = svm_sc8xx.o flash.o
diff --git a/board/svm_sc8xx/flash.c b/board/svm_sc8xx/flash.c
deleted file mode 100644
index 8a04de8..0000000
--- a/board/svm_sc8xx/flash.c
+++ /dev/null
@@ -1,666 +0,0 @@
-/*
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-#endif
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static int write_word(flash_info_t *info, ulong dest, ulong data);
-
-#ifdef CONFIG_BOOT_8B
-static int my_in_8(unsigned char *addr);
-static void my_out_8(unsigned char *addr, int val);
-#endif
-#ifdef CONFIG_BOOT_16B
-static int my_in_be16(unsigned short *addr);
-static void my_out_be16(unsigned short *addr, int val);
-#endif
-#ifdef CONFIG_BOOT_32B
-static unsigned my_in_be32(unsigned *addr);
-static void my_out_be32(unsigned *addr, int val);
-#endif
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init(void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long size_b0, size_b1;
- int i;
-
- size_b0 = 0;
- size_b1 = 0;
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i)
- flash_info[i].flash_id = FLASH_UNKNOWN;
-
-#ifdef CONFIG_SYS_DOC_BASE
-#ifndef CONFIG_FEL8xx_AT
- /* 32k bytes */
- memctl->memc_or5 = (0xffff8000 | CONFIG_SYS_OR_TIMING_DOC);
- memctl->memc_br5 = CONFIG_SYS_DOC_BASE | 0x401;
-#else
- /* 32k bytes */
- memctl->memc_or3 = (0xffff8000 | CONFIG_SYS_OR_TIMING_DOC);
- memctl->memc_br3 = CONFIG_SYS_DOC_BASE | 0x401;
-#endif
-#endif
-#if defined(CONFIG_BOOT_8B)
- size_b0 = 0x80000; /* 512 K */
-
- flash_info[0].flash_id = FLASH_MAN_AMD | FLASH_AM040;
- flash_info[0].sector_count = 8;
- flash_info[0].size = 0x00080000;
-
- /* set up sector start address table */
- for (i = 0; i < flash_info[0].sector_count; i++)
- flash_info[0].start[i] = 0x40000000 + (i * 0x10000);
-
- /* protect all sectors */
- for (i = 0; i < flash_info[0].sector_count; i++)
- flash_info[0].protect[i] = 0x1;
-
-#elif defined(CONFIG_BOOT_16B)
- size_b0 = 0x400000; /* 4MB , assume AMD29LV320B */
-
- flash_info[0].flash_id = FLASH_MAN_AMD | FLASH_AM320B;
- flash_info[0].sector_count = 67;
- flash_info[0].size = 0x00400000;
-
- /* set up sector start address table */
- flash_info[0].start[0] = 0x40000000;
- flash_info[0].start[1] = 0x40000000 + 0x4000;
- flash_info[0].start[2] = 0x40000000 + 0x6000;
- flash_info[0].start[3] = 0x40000000 + 0x8000;
-
- for (i = 4; i < flash_info[0].sector_count; i++) {
- flash_info[0].start[i] =
- 0x40000000 + 0x10000 + ((i - 4) * 0x10000);
- }
-
- /* protect all sectors */
- for (i = 0; i < flash_info[0].sector_count; i++)
- flash_info[0].protect[i] = 0x1;
-#endif
-
-#ifdef CONFIG_BOOT_32B
-
- /* Static FLASH Bank configuration here - FIXME XXX */
- size_b0 = flash_get_size((vu_long *) FLASH_BASE0_PRELIM,
- &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size_b0, size_b0 << 20);
- }
-
- size_b1 = flash_get_size((vu_long *) FLASH_BASE1_PRELIM,
- &flash_info[1]);
-
- if (size_b1 > size_b0) {
- printf("## ERROR: "
- "Bank 1 (0x%08lx = %ld MB) > Bank 0 (0x%08lx = %ld MB)\n",
- size_b1, size_b1 << 20, size_b0, size_b0 << 20);
- flash_info[0].flash_id = FLASH_UNKNOWN;
- flash_info[1].flash_id = FLASH_UNKNOWN;
- flash_info[0].sector_count = -1;
- flash_info[1].sector_count = -1;
- flash_info[0].size = 0;
- flash_info[1].size = 0;
-
- return 0;
- }
-
- /* Remap FLASH according to real size */
- memctl->memc_or0 = CONFIG_SYS_OR_TIMING_FLASH |
- (-size_b0 & OR_AM_MSK);
- memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) |
- BR_MS_GPCM | BR_V;
-
- /* Re-do sizing to get full correct info */
- size_b0 = flash_get_size((vu_long *) CONFIG_SYS_FLASH_BASE,
- &flash_info[0]);
-
- flash_get_offsets(CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]);
-#endif
-
- if (size_b1) {
- memctl->memc_or1 = CONFIG_SYS_OR_TIMING_FLASH |
- (-size_b1 & 0xFFFF8000);
- memctl->memc_br1 = ((CONFIG_SYS_FLASH_BASE +
- size_b0) & BR_BA_MSK) | BR_MS_GPCM | BR_V;
-
- /* Re-do sizing to get full correct info */
- size_b1 = flash_get_size((vu_long *)(CONFIG_SYS_FLASH_BASE +
- size_b0), &flash_info[1]);
-
- flash_get_offsets(CONFIG_SYS_FLASH_BASE + size_b0,
- &flash_info[1]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[1]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
- &flash_info[1]);
-#endif
- } else {
- memctl->memc_br1 = 0; /* invalidate bank */
-
- flash_info[1].flash_id = FLASH_UNKNOWN;
- flash_info[1].sector_count = -1;
- }
-
- flash_info[0].size = size_b0;
- flash_info[1].size = size_b1;
-
-
-#endif /* CONFIG_BOOT_32B */
-
- return size_b0 + size_b1;
-}
-
-
-void flash_print_info(flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD:
- printf("AMD ");
- break;
- case FLASH_MAN_FUJ:
- printf("FUJITSU ");
- break;
- default:
- printf("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM400B:
- printf("AM29LV400B (4 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM400T:
- printf("AM29LV400T (4 Mbit, top boot sector)\n");
- break;
- case FLASH_AM800B:
- printf("AM29LV800B (8 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM800T:
- printf("AM29LV800T (8 Mbit, top boot sector)\n");
- break;
- case FLASH_AM160B:
- printf("AM29LV160B (16 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM160T:
- printf("AM29LV160T (16 Mbit, top boot sector)\n");
- break;
- case FLASH_AM320B:
- printf("AM29LV320B (32 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM320T:
- printf("AM29LV320T (32 Mbit, top boot sector)\n");
- break;
- default:
- printf("Unknown Chip Type\n");
- break;
- }
-
- printf(" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf(" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf("\n ");
- printf(" %08lX%s",
- info->start[i], info->protect[i] ? " (RO)" : " ");
- }
- printf("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-int flash_erase(flash_info_t *info, int s_first, int s_last)
-{
- vu_long *addr = (vu_long *) (info->start[0]);
- int flag, prot, sect, l_sect, in_mid, in_did;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN)
- printf("- missing\n");
- else
- printf("- no sectors to erase\n");
-
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) ||
- (info->flash_id > FLASH_AMD_COMP)) {
- printf("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect])
- prot++;
- }
-
- if (prot) {
- printf("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
-#if defined(CONFIG_BOOT_8B)
- my_out_8((unsigned char *)((ulong)addr + 0x555), 0xaa);
- my_out_8((unsigned char *)((ulong)addr + 0x2aa), 0x55);
- my_out_8((unsigned char *)((ulong)addr + 0x555), 0x90);
-
- in_mid = my_in_8((unsigned char *)addr);
- in_did = my_in_8((unsigned char *)((ulong)addr + 1));
-
- printf(" man ID=0x%x, dev ID=0x%x.\n", in_mid, in_did);
-
- my_out_8((unsigned char *)addr, 0xf0);
- udelay(1);
-
- my_out_8((unsigned char *)((ulong)addr + 0x555), 0xaa);
- my_out_8((unsigned char *)((ulong)addr + 0x2aa), 0x55);
- my_out_8((unsigned char *)((ulong)addr + 0x555), 0x80);
- my_out_8((unsigned char *)((ulong)addr + 0x555), 0xaa);
- my_out_8((unsigned char *)((ulong)addr + 0x2aa), 0x55);
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_long *) (info->start[sect]);
- /*addr[0] = 0x00300030; */
- my_out_8((unsigned char *)((ulong)addr), 0x30);
- l_sect = sect;
- }
- }
-#elif defined(CONFIG_BOOT_16B)
- my_out_be16((unsigned short *)((ulong)addr + (0xaaa)), 0xaa);
- my_out_be16((unsigned short *)((ulong)addr + (0x554)), 0x55);
- my_out_be16((unsigned short *)((ulong)addr + (0xaaa)), 0x90);
- in_mid = my_in_be16((unsigned short *)addr);
- in_did = my_in_be16((unsigned short *)((ulong)addr + 2));
- printf(" man ID=0x%x, dev ID=0x%x.\n", in_mid, in_did);
- my_out_be16((unsigned short *)addr, 0xf0);
- udelay(1);
- my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0xaa);
- my_out_be16((unsigned short *)((ulong)addr + 0x554), 0x55);
- my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0x80);
- my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0xaa);
- my_out_be16((unsigned short *)((ulong)addr + 0x554), 0x55);
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_long *) (info->start[sect]);
- my_out_be16((unsigned short *)((ulong)addr), 0x30);
- l_sect = sect;
- }
- }
-
-#elif defined(CONFIG_BOOT_32B)
- my_out_be32((unsigned *)((ulong)addr + 0x1554), 0xaa);
- my_out_be32((unsigned *)((ulong)addr + 0xaa8), 0x55);
- my_out_be32((unsigned *)((ulong)addr + 0x1554), 0x90);
-
- in_mid = my_in_be32((unsigned *)addr);
- in_did = my_in_be32((unsigned *)((ulong)addr + 4));
-
- printf(" man ID=0x%x, dev ID=0x%x.\n", in_mid, in_did);
-
- my_out_be32((unsigned *) addr, 0xf0);
- udelay(1);
-
- my_out_be32((unsigned *)((ulong)addr + 0x1554), 0xaa);
- my_out_be32((unsigned *)((ulong)addr + 0xaa8), 0x55);
- my_out_be32((unsigned *)((ulong)addr + 0x1554), 0x80);
- my_out_be32((unsigned *)((ulong)addr + 0x1554), 0xaa);
- my_out_be32((unsigned *)((ulong)addr + 0xaa8), 0x55);
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_long *) (info->start[sect]);
- my_out_be32((unsigned *)((ulong)addr), 0x00300030);
- l_sect = sect;
- }
- }
-
-#else
-#error CONFIG_BOOT_(size)B missing.
-#endif
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay(1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer(0);
- last = start;
- addr = (vu_long *) (info->start[l_sect]);
-#if defined(CONFIG_BOOT_8B)
- while ((my_in_8((unsigned char *) addr) & 0x80) != 0x80)
-#elif defined(CONFIG_BOOT_16B)
- while ((my_in_be16((unsigned short *) addr) & 0x0080) != 0x0080)
-#elif defined(CONFIG_BOOT_32B)
- while ((my_in_be32((unsigned *) addr) & 0x00800080) != 0x00800080)
-#else
-#error CONFIG_BOOT_(size)B missing.
-#endif
- {
- now = get_timer(start);
- if (now > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc('.');
- last = now;
- }
- }
-DONE:
- /* reset to read mode */
- addr = (volatile unsigned long *) info->start[0];
-
-#if defined(CONFIG_BOOT_8B)
- my_out_8((unsigned char *) addr, 0xf0);
-#elif defined(CONFIG_BOOT_16B)
- my_out_be16((unsigned short *) addr, 0x00f0);
-#elif defined(CONFIG_BOOT_32B)
- my_out_be32((unsigned *) addr, 0x00F000F0); /* reset bank */
-#else
-#error CONFIG_BOOT_(size)B missing.
-#endif
- printf(" done\n");
- return 0;
-}
-
-/*
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- l = addr - wp;
-
- if (l != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp)
- data = (data << 8) | (*(uchar *) cp);
-
- for (; i < 4 && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < 4; ++i, ++cp)
- data = (data << 8) | (*(uchar *) cp);
-
- rc = write_word(info, wp, data);
-
- if (rc != 0)
- return rc;
-
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i = 0; i < 4; ++i)
- data = (data << 8) | *src++;
-
- rc = write_word(info, wp, data);
-
- if (rc != 0)
- return rc;
-
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0)
- return 0;
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < 4; ++i, ++cp)
- data = (data << 8) | (*(uchar *) cp);
-
- return write_word(info, wp, data);
-}
-
-/*
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word(flash_info_t *info, ulong dest, ulong data)
-{
- ulong addr = (ulong) (info->start[0]);
- ulong start;
- int flag;
- ulong i;
- int data_short[2];
-
- /* Check if Flash is (sufficiently) erased */
- if (((ulong)*(ulong *)dest & data) != data)
- return 2;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-#if defined(CONFIG_BOOT_8B)
-#ifdef DEBUG
- {
- int in_mid, in_did;
-
- my_out_8((unsigned char *) (addr + 0x555), 0xaa);
- my_out_8((unsigned char *) (addr + 0x2aa), 0x55);
- my_out_8((unsigned char *) (addr + 0x555), 0x90);
-
- in_mid = my_in_8((unsigned char *) addr);
- in_did = my_in_8((unsigned char *) (addr + 1));
-
- printf(" man ID=0x%x, dev ID=0x%x.\n", in_mid, in_did);
-
- my_out_8((unsigned char *) addr, 0xf0);
- udelay(1);
- }
-#endif
- {
- int data_ch[4];
-
- data_ch[0] = (int) ((data >> 24) & 0xff);
- data_ch[1] = (int) ((data >> 16) & 0xff);
- data_ch[2] = (int) ((data >> 8) & 0xff);
- data_ch[3] = (int) (data & 0xff);
-
- for (i = 0; i < 4; i++) {
- my_out_8((unsigned char *) (addr + 0x555), 0xaa);
- my_out_8((unsigned char *) (addr + 0x2aa), 0x55);
- my_out_8((unsigned char *) (addr + 0x555), 0xa0);
- my_out_8((unsigned char *) (dest + i), data_ch[i]);
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- start = get_timer(0);
- while ((my_in_8((unsigned char *)(dest + i))) !=
- (data_ch[i])) {
- if (get_timer(start) >
- CONFIG_SYS_FLASH_WRITE_TOUT) {
- return 1;
- }
- }
- } /* for */
- }
-#elif defined(CONFIG_BOOT_16B)
- data_short[0] = (int) (data >> 16) & 0xffff;
- data_short[1] = (int) data & 0xffff;
- for (i = 0; i < 2; i++) {
- my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0xaa);
- my_out_be16((unsigned short *)((ulong)addr + 0x554), 0x55);
- my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0xa0);
- my_out_be16((unsigned short *)(dest + (i * 2)),
- data_short[i]);
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- start = get_timer(0);
- while ((my_in_be16((unsigned short *)(dest + (i * 2)))) !=
- (data_short[i])) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT)
- return 1;
- }
- }
-#elif defined(CONFIG_BOOT_32B)
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
- addr[0x0555] = 0x00A000A0;
-
- *((vu_long *)dest) = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer(0);
- while ((*((vu_long *)dest) & 0x00800080) != (data & 0x00800080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT)
- return 1;
- }
-#endif
- return 0;
-}
-
-#ifdef CONFIG_BOOT_8B
-static int my_in_8(unsigned char *addr)
-{
- int ret;
- __asm__ __volatile__("lbz%U1%X1 %0,%1; eieio":"=r"(ret):"m"(*addr));
-
- return ret;
-}
-
-static void my_out_8(unsigned char *addr, int val)
-{
- __asm__ __volatile__("stb%U0%X0 %1,%0; eieio":"=m"(*addr):"r"(val));
-}
-#endif
-#ifdef CONFIG_BOOT_16B
-static int my_in_be16(unsigned short *addr)
-{
- int ret;
- __asm__ __volatile__("lhz%U1%X1 %0,%1; eieio":"=r"(ret):"m"(*addr));
-
- return ret;
-}
-
-static void my_out_be16(unsigned short *addr, int val)
-{
- __asm__ __volatile__("sth%U0%X0 %1,%0; eieio":"=m"(*addr):"r"(val));
-}
-#endif
-#ifdef CONFIG_BOOT_32B
-static unsigned my_in_be32(unsigned *addr)
-{
- unsigned ret;
- __asm__ __volatile__("lwz%U1%X1 %0,%1; eieio":"=r"(ret):"m"(*addr));
-
- return ret;
-}
-
-static void my_out_be32(unsigned *addr, int val)
-{
- __asm__ __volatile__("stw%U0%X0 %1,%0; eieio":"=m"(*addr):"r"(val));
-}
-#endif
diff --git a/board/svm_sc8xx/svm_sc8xx.c b/board/svm_sc8xx/svm_sc8xx.c
deleted file mode 100644
index 5db4850..0000000
--- a/board/svm_sc8xx/svm_sc8xx.c
+++ /dev/null
@@ -1,144 +0,0 @@
-/*
- * (C) Copyright 2000, 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-/* ------------------------------------------------------------------------- */
-const uint sdram_table[] =
-{
-/*-----------------
- UPM A contents:
------------------ */
-/*---------------------------------------------------
- Read Single Beat Cycle. Offset 0 in the RAM array.
----------------------------------------------------- */
-0x1f07fc04, 0xeeaefc04, 0x11adfc04, 0xefbbbc00 ,
-0x1ff77c47, 0x1ff77c35, 0xefeabc34, 0x1fb57c35 ,
-/*------------------------------------------------
- Read Burst Cycle. Offset 0x8 in the RAM array.
------------------------------------------------- */
-0x1f07fc04, 0xeeaefc04, 0x10adfc04, 0xf0affc00,
-0xf0affc00, 0xf1affc00, 0xefbbbc00, 0x1ff77c47,
-0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
-0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff,
-/*-------------------------------------------------------
- Write Single Beat Cycle. Offset 0x18 in the RAM array
-------------------------------------------------------- */
-0x1f27fc04, 0xeeaebc00, 0x01b93c04, 0x1ff77c47 ,
-0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff ,
-/*-------------------------------------------------
- Write Burst Cycle. Offset 0x20 in the RAM array
-------------------------------------------------- */
-0x1f07fc04, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
-0xf0affc00, 0xe1bbbc04, 0x1ff77c47, 0xffffffff,
-0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff ,
-0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff ,
-/*------------------------------------------------------------------------
- Periodic Timer Expired. For DRAM refresh. Offset 0x30 in the RAM array
------------------------------------------------------------------------- */
-0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04,
-0xfffffc84, 0xfffffc07, 0xffffffff, 0xffffffff,
-0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff ,
-/*-----------
-* Exception:
-* ----------- */
-0x7ffefc07, 0xffffffff, 0xffffffff, 0xffffffff ,
-};
-
-/* ------------------------------------------------------------------------- */
-/*
- * Check Board Identity:
- *
- * Test ID string (SVM8...)
- *
- * Return 1 for "SC8xx" type, 0 else.
- */
-
-int checkboard(void)
-{
- char buf[64];
- int i;
- int l = getenv_f("serial#", buf, sizeof(buf));
-
- if (l < 0 || strncmp(buf, "SVM8", 4)) {
- printf("### No HW ID - assuming SVM SC8xx\n");
- return (0);
- }
-
- for (i = 0; i < l; ++i) {
- if (buf[i] == ' ')
- break;
- putc(buf[i]);
- }
-
- putc('\n');
-
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- long int size_b0 = 0;
-
- upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-#if defined (CONFIG_SDRAM_16M)
- memctl->memc_mamr = 0x00802114 | CONFIG_SYS_MxMR_PTx;
- memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
- udelay(1);
- memctl->memc_mcr = 0x80002830;
- udelay(1);
- memctl->memc_mar = 0x00000088;
- udelay(1);
- memctl->memc_mcr = 0x80002106;
- udelay(1);
- memctl->memc_or1 = 0xff000a00;
- size_b0 = 0x01000000;
-#elif defined (CONFIG_SDRAM_32M)
- memctl->memc_mamr = 0x00904114 | CONFIG_SYS_MxMR_PTx;
- memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
- udelay(1);
- memctl->memc_mcr = 0x80002830;
- udelay(1);
- memctl->memc_mar = 0x00000088;
- udelay(1);
- memctl->memc_mcr = 0x80002106;
- udelay(1);
- memctl->memc_or1 = 0xfe000a00;
- size_b0 = 0x02000000;
-#elif defined (CONFIG_SDRAM_64M)
- memctl->memc_mamr = 0x00a04114 | CONFIG_SYS_MxMR_PTx;
- memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
- udelay(1);
- memctl->memc_mcr = 0x80002830;
- udelay(1);
- memctl->memc_mar = 0x00000088;
- udelay(1);
- memctl->memc_mcr = 0x80002106;
- udelay(1);
- memctl->memc_or1 = 0xfc000a00;
- size_b0 = 0x04000000;
-#else
-#error SDRAM size configuration missing.
-#endif
- memctl->memc_br1 = 0x00000081;
- udelay(200);
- return (size_b0 );
-}
-
-#if defined(CONFIG_CMD_DOC)
-void doc_init (void)
-{
- doc_probe (CONFIG_SYS_DOC_BASE);
-}
-#endif
diff --git a/board/svm_sc8xx/u-boot.lds b/board/svm_sc8xx/u-boot.lds
deleted file mode 100644
index df564e9..0000000
--- a/board/svm_sc8xx/u-boot.lds
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
- lib/built-in.o (.text*)
- net/built-in.o (.text*)
- arch/powerpc/cpu/mpc8xx/built-in.o (.text*)
- arch/powerpc/lib/built-in.o (.text*)
- board/svm_sc8xx/built-in.o (.text*)
- *(.text.*printf)
- *(.text.do_mem_*)
- *(.text.flash*)
- *(.text.run_command)
- *(.text.main_loop)
- *(.text.srec_decode)
-
- . = env_offset;
- common/env_embedded.o (.ppcenv*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/board/svm_sc8xx/u-boot.lds.debug b/board/svm_sc8xx/u-boot.lds.debug
deleted file mode 100644
index b2c562c..0000000
--- a/board/svm_sc8xx/u-boot.lds.debug
+++ /dev/null
@@ -1,114 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text)
- common/dlmalloc.o (.text)
- lib/vsprintf.o (.text)
- lib/crc32.o (.text)
-
- . = env_offset;
- common/env_embedded.o(.text)
-
- *(.text)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/configs/svm_sc8xx_defconfig b/configs/svm_sc8xx_defconfig
deleted file mode 100644
index 9f0d343..0000000
--- a/configs/svm_sc8xx_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_SVM_SC8XX=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index b7b16d1..55b2c23 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+svm_sc8xx powerpc mpc8xx - - John Zhan <zhanz at sinovee.com>
stxxtc powerpc mpc8xx - - Dan Malek <dan at embeddedalley.com>
omap5912osk arm arm926ejs - - Rishi Bhattacharya <rishi at ti.com>
p1023rds powerpc mpc85xx d0bc5140 2014-07-22 Roy Zang <tie-fei.zang at freescale.com>
diff --git a/drivers/pcmcia/tqm8xx_pcmcia.c b/drivers/pcmcia/tqm8xx_pcmcia.c
index dda7d37..8b74478 100644
--- a/drivers/pcmcia/tqm8xx_pcmcia.c
+++ b/drivers/pcmcia/tqm8xx_pcmcia.c
@@ -20,14 +20,12 @@
#endif
#if defined(CONFIG_PCMCIA) \
- && (defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx))
+ && defined(CONFIG_TQM8xxL)
#if defined(CONFIG_VIRTLAB2)
#define PCMCIA_BOARD_MSG "Virtlab2"
#elif defined(CONFIG_TQM8xxL)
#define PCMCIA_BOARD_MSG "TQM8xxL"
-#elif defined(CONFIG_SVM_SC8xx)
-#define PCMCIA_BOARD_MSG "SC8xx"
#endif
#if defined(CONFIG_NSCU)
@@ -302,4 +300,4 @@ done:
return 0;
}
-#endif /* CONFIG_PCMCIA && (CONFIG_TQM8xxL || CONFIG_SVM_SC8xx) */
+#endif /* CONFIG_PCMCIA && CONFIG_TQM8xxL */
diff --git a/include/commproc.h b/include/commproc.h
index 52ac4ca..fec818d 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -779,57 +779,6 @@ typedef struct scc_enet {
/*** NETVIA *******************************************************/
-/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */
-#if ( defined CONFIG_SVM_SC8xx )
-# ifndef CONFIG_FEC_ENET
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-
- /* Bits in parallel I/O port registers that have to be set/cleared
- * * * * to configure the pins for SCC2 use.
- * * * */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- * * * */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003700)
-
-# else /* Use FEC for Fast Ethernet */
-
-#undef SCC_ENET
-#define FEC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-# endif /* CONFIG_FEC_ENET */
-#endif /* CONFIG_SVM_SC8xx */
-
-
#if defined(CONFIG_NETVIA)
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
diff --git a/include/configs/svm_sc8xx.h b/include/configs/svm_sc8xx.h
deleted file mode 100644
index b4aa948..0000000
--- a/include/configs/svm_sc8xx.h
+++ /dev/null
@@ -1,450 +0,0 @@
-/*
- * (C) Copyright 2000, 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific,
- * for SinoVee Microsystems SC8xx series SBC
- * http://www.fel.com.cn (Chinese)
- * http://www.sinovee.com (English)
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-/* Custom configuration */
-/* SC823,SC850,SC860SAR, FEL8xx-AT(823/850/860) */
-/* SC85T,SC860T, FEL8xx-AT(855T/860T) */
-/*#define CONFIG_FEL8xx_AT */
-/*#define CONFIG_LCD */
-/*#define CONFIG_MPC8XX_LCD*/
-/* if core > 50MHz , un-comment CONFIG_BUS_DIV2 */
-/* #define CONFIG_50MHz */
-/* #define CONFIG_66MHz */
-/* #define CONFIG_75MHz */
-#define CONFIG_80MHz
-/*#define CONFIG_100MHz */
-/* #define CONFIG_BUS_DIV2 1 */
-/* for BOOT device port size */
-/* #define CONFIG_BOOT_8B */
-#define CONFIG_BOOT_16B
-/* #define CONFIG_BOOT_32B */
-/* #define CONFIG_CAN_DRIVER */
-/* #define DEBUG */
-#define CONFIG_FEC_ENET
-
-/* #define CONFIG_SDRAM_16M */
-#define CONFIG_SDRAM_32M
-/* #define CONFIG_SDRAM_64M */
-#define CONFIG_SYS_RESET_ADDRESS 0xffffffff
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-/* #define CONFIG_MPC823 1 */
-/* #define CONFIG_MPC850 1 */
-#define CONFIG_MPC855 1
-/* #define CONFIG_MPC860 1 */
-/* #define CONFIG_MPC860T 1 */
-
-#undef CONFIG_WATCHDOG /* watchdog */
-
-#define CONFIG_SVM_SC8xx 1 /* ...on SVM SC8xx series */
-
-#ifdef CONFIG_LCD /* with LCD controller ? */
-/* #define CONFIG_NEC_NL6448BC20 1 / * use NEC NL6448BC20 display */
-#endif
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 19200 /* console baudrate = 115kbps */
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#define CONFIG_BOARD_TYPES 1 /* support board types */
-
-#define CONFIG_PREBOOT "echo;echo Welcome to U-Boot SVM port;echo;echo Type \"? or help\" to get on-line help;echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 0x210000 ${bootfile};run nfsargs addip;bootm\0" \
- "rootpath=/opt/sinovee/ppc8xx-linux-2.0/target\0" \
- "bootfile=pImage-sc855t\0" \
- "kernel_addr=48000000\0" \
- "ramdisk_addr=48100000\0" \
- ""
-#define CONFIG_BOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "tftpboot 0x210000 pImage-sc855t;bootm 0x210000"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-
-#ifdef CONFIG_LCD
-# undef CONFIG_STATUS_LED /* disturbs display */
-#else
-# define CONFIG_STATUS_LED 1 /* Status LED enabled */
-#endif /* CONFIG_LCD */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DATE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#ifdef CONFIG_SYS_HUSH_PARSER
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-
-#ifdef CONFIG_BOOT_8B
-#define CONFIG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
-#elif defined (CONFIG_BOOT_16B)
-#define CONFIG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
-#elif defined (CONFIG_BOOT_32B)
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-#endif
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC 0x46454C38 /* 'SVM8' */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-/*#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-*/
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR 0xffffff88
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-/*#define CONFIG_SYS_SIUMCR 0x00610c00 */
-#define CONFIG_SYS_SIUMCR 0x00000000
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR 0x0001
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC 0x00c3
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR 0x0000
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#if defined (CONFIG_100MHz)
-#define CONFIG_SYS_PLPRCR 0x06301000
-#define CONFIG_8xx_GCLK_FREQ 100000000
-#elif defined (CONFIG_80MHz)
-#define CONFIG_SYS_PLPRCR 0x04f01000
-#define CONFIG_8xx_GCLK_FREQ 80000000
-#elif defined(CONFIG_75MHz)
-#define CONFIG_SYS_PLPRCR 0x04a00100
-#define CONFIG_8xx_GCLK_FREQ 75000000
-#elif defined(CONFIG_66MHz)
-#define CONFIG_SYS_PLPRCR 0x04101000
-#define CONFIG_8xx_GCLK_FREQ 66000000
-#elif defined(CONFIG_50MHz)
-#define CONFIG_SYS_PLPRCR 0x03101000
-#define CONFIG_8xx_GCLK_FREQ 50000000
-#endif
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#ifdef CONFIG_BUS_DIV2
-#define CONFIG_SYS_SCCR 0x02020000 | SCCR_RTSEL
-#else /* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_SCCR 0x02000000 | SCCR_RTSEL
-#endif
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_INIT_POSTRESET 1 /* Use postreset IDE hook */
-#define CONFIG_IDE_8xx_DIRECT 1 /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_BASE_ADDR 0xFE100010
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-/*#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0C00 */
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O
- */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0200 /* Offset for normal register accesses
- */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0210 /* Offset for alternate registers
- */
-#define CONFIG_ATAPI
-#define CONFIG_SYS_PIO_MODE 0
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/*#define CONFIG_SYS_DER 0x2002000F*/
-#define CONFIG_SYS_DER 0x0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#if defined(CONFIG_100MHz)
-#define CONFIG_SYS_OR_TIMING_FLASH 0x000002f4
-#define CONFIG_SYS_OR_TIMING_DOC 0x000002f4
-#define CONFIG_SYS_MxMR_PTx 0x61000000
-#define CONFIG_SYS_MPTPR 0x400
-
-#elif defined(CONFIG_80MHz)
-#define CONFIG_SYS_OR_TIMING_FLASH 0x00000ff4
-#define CONFIG_SYS_OR_TIMING_DOC 0x000001f4
-#define CONFIG_SYS_MxMR_PTx 0x4e000000
-#define CONFIG_SYS_MPTPR 0x400
-
-#elif defined(CONFIG_75MHz)
-#define CONFIG_SYS_OR_TIMING_FLASH 0x000008f4
-#define CONFIG_SYS_OR_TIMING_DOC 0x000002f4
-#define CONFIG_SYS_MxMR_PTx 0x49000000
-#define CONFIG_SYS_MPTPR 0x400
-
-#elif defined(CONFIG_66MHz)
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-/*#define CONFIG_SYS_OR_TIMING_FLASH 0x000001f4 */
-#define CONFIG_SYS_OR_TIMING_DOC 0x000003f4
-#define CONFIG_SYS_MxMR_PTx 0x40000000
-#define CONFIG_SYS_MPTPR 0x400
-
-#else /* 50 MHz */
-#define CONFIG_SYS_OR_TIMING_FLASH 0x00000ff4
-#define CONFIG_SYS_OR_TIMING_DOC 0x000001f4
-#define CONFIG_SYS_MxMR_PTx 0x30000000
-#define CONFIG_SYS_MPTPR 0x400
-#endif /*CONFIG_??MHz */
-
-
-#if defined (CONFIG_BOOT_8B) /* 512K X 8 ,29F040 , 2MB space */
-#define CONFIG_SYS_OR0_PRELIM (0xffe00000 | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_8)
-#elif defined (CONFIG_BOOT_16B) /* 29lv160 X 16 , 4MB space */
-#define CONFIG_SYS_OR0_PRELIM (0xffc00000 | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16)
-#elif defined( CONFIG_BOOT_32B ) /* 29lv160 X 2 X 32, 4/8/16MB , 64MB space */
-#define CONFIG_SYS_OR0_PRELIM (0xfc000000 | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-#else
-#error Boot device port size missing.
-#endif
-
-/*
- * Disk-On-Chip configuration
- */
-
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-#define CONFIG_SYS_DOC_BASE 0x80000000
-
-#endif /* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 8aec254..4b667f4 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -21,7 +21,7 @@
#if !defined(CONFIG_PCMCIA_SLOT_A) && !defined(CONFIG_PCMCIA_SLOT_B)
-#if defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx)
+#if defined(CONFIG_TQM8xxL)
# define CONFIG_PCMCIA_SLOT_B /* The TQM8xxL use SLOT_B */
#elif defined(CONFIG_SPD823TS) /* The SPD8xx use SLOT_B */
# define CONFIG_PCMCIA_SLOT_B
diff --git a/include/status_led.h b/include/status_led.h
index a41d3bc..c9d21d1 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -217,20 +217,6 @@ void status_led_set (int led, int state);
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-#elif defined(CONFIG_SVM_SC8xx)
-# define STATUS_LED_PAR im_cpm.cp_pbpar
-# define STATUS_LED_DIR im_cpm.cp_pbdir
-# define STATUS_LED_ODR im_cpm.cp_pbodr
-# define STATUS_LED_DAT im_cpm.cp_pbdat
-
-# define STATUS_LED_BIT 0x00000001
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
#elif defined(CONFIG_V38B)
# define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */
--
1.9.1
More information about the U-Boot
mailing list