[U-Boot] [PATCH V2 17/18] arm: mx6: cm_fx6: use eeprom

[Nikita Kiryanov]

Use Compulab eeprom module to obtain revision number, serial number, and
mac address from the EEPROM.

Cc: Igor Grinberg <grinberg at compulab.co.il>
Cc: Stefano Babic <sbabic at denx.de>
Cc: Tom Rini <trini at ti.com>
Signed-off-by: Nikita Kiryanov <nikita at compulab.co.il>
---
Changes in V2:
	- No changes

 board/compulab/cm_fx6/cm_fx6.c | 26 +++++++++++++++++++++++++-
 include/configs/cm_fx6.h       |  2 ++
 2 files changed, 27 insertions(+), 1 deletion(-)

diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index 1b967e5..76d7430 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -19,6 +19,7 @@
 #include <asm/io.h>
 #include <asm/gpio.h>
 #include "common.h"
+#include "../common/eeprom.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -207,8 +208,31 @@ static iomux_v3_cfg_t const enet_pads[] = {
 						MUX_PAD_CTRL(ENET_PAD_CTRL)),
 };
 
+static int handle_mac_address(void)
+{
+	unsigned char enetaddr[6];
+	int rc;
+
+	rc = eth_getenv_enetaddr("ethaddr", enetaddr);
+	if (rc)
+		return 0;
+
+	rc = cl_eeprom_read_mac_addr(enetaddr);
+	if (rc)
+		return rc;
+
+	if (!is_valid_ether_addr(enetaddr))
+		return -1;
+
+	return eth_setenv_enetaddr("ethaddr", enetaddr);
+}
+
 int board_eth_init(bd_t *bis)
 {
+	int res = handle_mac_address();
+	if (res)
+		puts("No MAC address found\n");
+
 	SETUP_IOMUX_PADS(enet_pads);
 	/* phy reset */
 	gpio_direction_output(CM_FX6_ENET_NRST, 0);
@@ -348,5 +372,5 @@ int dram_init(void)
 
 u32 get_board_rev(void)
 {
-	return 100;
+	return cl_eeprom_get_board_rev();
 }
diff --git a/include/configs/cm_fx6.h b/include/configs/cm_fx6.h
index 0aa88fd..adfd55e 100644
--- a/include/configs/cm_fx6.h
+++ b/include/configs/cm_fx6.h
@@ -236,6 +236,8 @@
 #define CONFIG_SYS_BOOTMAPSZ	        (8 << 20)
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SERIAL_TAG
 
 /* misc */
 #define CONFIG_SYS_GENERIC_BOARD
-- 
1.9.1