[U-Boot] [PATCH v6 2/2] net: fec_mxc: Poll FEC_TBD_READY after polling TDAR

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam at freescale.com>

When testing the FEC driver on a mx6solox we noticed that the TDAR bit gets
always cleared prior then the READY bit is cleared in the last BD, which causes
FEC packets reception to always fail.

As explained by Ye Li:

"The TDAR bit is cleared when the descriptors are all out from TX ring, but on 
mx6solox we noticed that the READY bit is still not cleared right after TDAR. 
These are two distinct signals, and in IC simulation, we found that TDAR always
gets cleared prior than the READY bit of last BD becomes cleared. 
In mx6solox, we use a later version of FEC IP. It looks like that this 
intrinsic behaviour of TDAR bit has changed in this newer FEC version."

Fix this by polling the READY bit of BD after the TDAR polling, which covers the
mx6solox case and does not harm the other SoCs.

No performance drop has been noticed with this patch applied when testing TFTP
transfers on several boards of different i.mx SoCs.

Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
---
Changes since v5:
- Put explanation why we need to poll READY bit after TDAR into the code

 drivers/net/fec_mxc.c | 29 ++++++++++++++++++++++++++---
 1 file changed, 26 insertions(+), 3 deletions(-)

diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index 6afc827..bdd8108 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -719,13 +719,36 @@ static int fec_send(struct eth_device *dev, void *packet, int length)
 			break;
 	}
 
-	if (!timeout)
+	if (!timeout) {
 		ret = -EINVAL;
+		goto out;
+	}
 
-	invalidate_dcache_range(addr, addr + size);
-	if (readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_READY)
+	/*
+	 * The TDAR bit is cleared when the descriptors are all out from TX
+	 * but on mx6solox we noticed that the READY bit is still not cleared
+	 * right after TDAR.
+	 * These are two distinct signals, and in IC simulation, we found that
+	 * TDAR always gets cleared prior than the READY bit of last BD becomes
+	 * cleared.
+	 * In mx6solox, we use a later version of FEC IP. It looks like that
+	 * this intrinsic behaviour of TDAR bit has changed in this newer FEC
+	 * version.
+	 *
+	 * Fix this by polling the READY bit of BD after the TDAR polling,
+	 * which covers the mx6solox case and does not harm the other SoCs.
+	 */
+	timeout = FEC_XFER_TIMEOUT;
+	while (--timeout) {
+		invalidate_dcache_range(addr, addr + size);
+		if (!(readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_READY))
+			break;
+	}
+
+	if (!timeout)
 		ret = -EINVAL;
 
+out:
 	debug("fec_send: status 0x%x index %d ret %i\n",
 			readw(&fec->tbd_base[fec->tbd_index].status),
 			fec->tbd_index, ret);
-- 
1.9.1